Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278157 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


PROCEDURE

Hide 67750 1.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

Hide 67761A 2.REMOVE BACK DOOR TRIM COVER

Hide 3.REMOVE REAR SPOILER ASSEMBLY

Hide 68131 4.REMOVE BACK DOOR GLASS SUB-ASSEMBLY

a.

Disconnect each connector.


b.
B296205E02
0.435,0.38 0.671,0.569 0.236,0.189 10 *1 0.871,0.72 0.624,0.482 false

Apply protective tape to the area around the installation position of the back door glass on the vehicle body to prevent it from being scratched.

Text in Illustration
*1 Protective Tape

HINT:

Apply protective tape to the vehicle body to prevent it from being scratched.



c.
B296206E02
1.667,0.51 1.448,0.51 1.448,0.51 1.448,0.885 true 1.656,0.781 1.448,0.781 false 1.365,0.896 1.615,1.104 0.25,0.208 10 false *1

Place matchmarks on the back door glass and vehicle body on the locations indicated in the illustration.

Text in Illustration
*1 Matchmark

HINT:

Matchmarks are not needed to be placed if the back door glass will not be reused.



d.
B296207E03
0.75,0.698 0.552,0.583 true 0.854,0.802 0.531,0.823 true 2.323,1.073 1.74,1.885 1.74,1.885 1.125,1.073 true 0.354,0.49 0.615,0.719 0.26,0.229 10 false *1 0.344,0.74 0.604,0.969 0.26,0.229 10 false *2 1.635,1.917 1.813,2.094 0.177,0.177 10 true *3

Pass a piano wire between the vehicle body and glass from the interior.

Text in Illustration
*1 Piano Wire
*2 Back Window Glass Clip
*3 Window Defogger Connector


e.

Tie both wire ends to wooden blocks or similar objects.


f.

Cut off the adhesive by pulling the piano wire around the back door glass.

NOTICE:

When separating the back door glass, take care not to damage the paint or interior and exterior ornaments.



g.
B296208

Using suction cups, disengage the 2 clips and remove the back door glass sub-assembly.

NOTICE:
·

To prevent the back door glass from falling when performing this operation, be sure to hold the back door glass using suction cups.

·

Be careful not to drop the back door glass.

·

Leave as much adhesive on the vehicle body as possible when removing the back door glass.




Hide 64813B 5.REMOVE BACK WINDOW GLASS ADHESIVE DAM

a.

When reusing the back door glass:

i.
B298782E02
0.108,0.068 0.331,0.237 0.223,0.168 10 *A

Using a scraper, remove the back window glass adhesive dam.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass adhesive dam with a new one.





Hide 64828B 6.REMOVE BACK WINDOW GLASS CLIP LH

a.

When reusing the back door glass:

i.
B298781E02
0.083,0.042 0.302,0.292 0.219,0.25 10 false *A

Using a scraper, remove the back window glass clip LH.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass clip LH with new one.





Hide 64827B 7.REMOVE BACK WINDOW GLASS CLIP RH

a.

When reusing the back door glass:

i.
B298780E02
0.083,0.031 0.302,0.281 0.219,0.25 10 false *A

Using a scraper, remove the back window glass clip RH.

Text in Illustration
*A Back Side

NOTICE:
·

Be careful not to damage the back door glass.

·

Be sure to replace the back window glass clip RH with new one.





Hide 8.CLEAN BACK DOOR GLASS

a.

Using a scraper, remove any adhesive dam and adhesive residue from the back door glass.

NOTICE:

Be careful not to damage the back door glass.



b.
B187131

Clean the outer circumference of the back door glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the back door glass.

·

Even if using new glass, clean it with a non-residue solvent.




Hide 9. CLEAN VEHICLE BODY

a.
B296195E01
0.72,1.631 0.946,1.783 0.226,0.152 10 *1 0.579,1.412 0.783,1.631 false 0.807,0.903 0.557,0.472 0.557,0.472 0.423,0.472 false 0.22,0.387 0.446,0.539 0.226,0.152 10 *2

Clean and shape the contact surface of the vehicle body.

Text in Illustration
*1 Body
*2 Adhesive

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.