Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278160 FRONT DOOR N

DOOR / HATCH  FRONT DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B211130E08
0.669,0.195 0.896,0.423 0.227,0.228 10 *1 2.557,0.195 2.783,0.423 0.227,0.228 10 *2

HINT:
Text in Illustration
*1 Centering Bolt
*2 Standard Bolt

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS)



PROCEDURE

Hide 67001 1.INSPECT FRONT DOOR

a.

Check that the clearance measurements of areas "a" through "i" are within each standard range.

B301507E03
0.949,2.432 1.141,2.579 0.192,0.148 10 a 2.246,1.08 2.439,1.228 0.192,0.148 10 b 2.447,0.431 2.639,0.579 0.192,0.148 10 c 3.82,1.06 4.012,1.208 0.192,0.148 10 d 4.026,0.443 4.218,0.590 0.192,0.148 10 e 5.986,1.725 6.179,1.873 0.192,0.148 10 f 2.306,4.939 2.498,5.087 0.192,0.148 10 g 3.868,5.076 4.060,5.224 0.192,0.148 10 h 6.057,4.828 6.249,4.976 0.192,0.148 10 i

Standard Clearance
Area Measurement Area Measurement
a 2.7 to 5.7 mm (0.106 to 0.224 in.) b 1.9 to 4.9 mm (0.0748 to 0.193 in.)
c 3.2 to 6.2 mm (0.126 to 0.244 in.) d 2.0 to 5.0 mm (0.0787 to 0.197 in.)
e 3.2 to 6.2 mm (0.126 to 0.244 in.) f 3.2 to 6.2 mm (0.126 to 0.244 in.)
g 4.2 to 7.2 mm (0.165 to 0.283 in.) h 4.2 to 7.2 mm (0.165 to 0.283 in.)
i 3.2 to 6.2 mm (0.126 to 0.244 in.) - -


Hide 67001 2.ADJUST FRONT DOOR

NOTICE:

Make sure to turn the power switch off when adjusting door lock strikers.


a.
B297607

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the body side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Tighten the door side hinge bolts after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.
B297608

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


e.

Using a brass bar and a hammer, hit the striker to adjust its position.


f.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)