Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278161 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B211130E06
0.669,0.195 0.896,0.423 0.227,0.228 10 *1 2.557,0.195 2.783,0.423 0.227,0.228 10 *2

Text in Illustration
*1 Centering Bolt
*2 Standard Bolt

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Specified torque for standard bolts is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT REAR DOOR

a.

Check that the clearance measurements of areas "a" through "m" are within each standard range.

B301508E01
1.074,2.375 1.268,2.561 0.194,0.186 10 a 1.635,2.126 1.829,2.312 0.194,0.186 10 b 2.232,0.595 2.426,0.781 0.194,0.186 10 c 2.254,1.37 2.448,1.556 0.194,0.186 10 d 3.783,0.581 3.978,0.767 0.194,0.186 10 e 3.798,1.371 3.992,1.557 0.194,0.186 10 f 6.001,2.143 6.195,2.329 0.194,0.186 10 g 6.396,1.91 6.590,2.096 0.194,0.186 10 h 6.503,3.898 6.697,4.084 0.194,0.186 10 i 6.084,4.612 6.278,4.798 0.194,0.186 10 j 3.912,4.945 4.106,5.131 0.194,0.186 10 k 3.026,5.281 3.220,5.467 0.194,0.186 10 l 2.242,5.03 2.436,5.216 0.194,0.186 10 m

Standard Clearance
Area Measurement Area Measurement
a 3.2 to 6.2 mm (0.126 to 0.244 in.) b -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
c 3.2 to 6.2 mm (0.126 to 0.244 in.) d 2.1 to 5.1 mm (0.0827 to 0.167 in.)
e 3.2 to 6.2 mm (0.126 to 0.244 in.) f 2.3 to 5.3 mm (0.0906 to 0.209 in.)
g 2.7 to 5.7 mm (0.106 to 0.224 in.) h -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
i -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) j 2.7 to 5.7 mm (0.106 to 0.224 in.)
k 4.2 to 7.2 mm (0.165 to 0.283 in.) l 3.2 to 6.2 mm (0.126 to 0.244 in.)
m -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -


Hide 2.ADJUST REAR DOOR

NOTICE:

Make sure to turn the power switch off when adjusting door lock strikers.


a.
B297646

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B297644

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)