Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › 2011.12–2017.06
RM2170E _59 Vehicle Exterior _057047 MIRROR (EXT) _0278171 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retractable Mirror)

a.
B127217E04
2.979,0.692 3.163,0.859 0.184,0.166 10 *1 0.771,4.296 0.889,4.442 0.118,0.145 10 B 1.033,4.296 1.151,4.442 0.118,0.145 10 E 1.282,4.296 1.503,4.444 0.221,0.148 10 M+ 1.619,4.296 1.825,4.444 0.206,0.148 10 HL 1.914,4.296 2.112,4.444 0.198,0.148 10 VL 2.23,4.296 2.441,4.444 0.211,0.148 10 VR 2.586,4.296 2.812,4.444 0.226,0.148 10 HR 1.296,3.904 0.828,4.279 false 1.436,3.906 1.109,4.264 false 1.597,3.909 1.427,4.261 false 1.742,3.906 1.742,4.255 false 1.896,3.91 2.004,4.262 false 2.051,3.907 2.343,4.256 false 2.205,3.907 2.67,4.262 false 0.292,2.948 0.448,3.129 0.156,0.181 10 *a 2.945,0.775 2.151,0.775 false 3.051,2.002 3.234,2.168 0.184,0.166 10 *2 3.017,2.085 2.222,2.085 false

Check the resistance.

Text in Illustration
*1 Left / Right Select Switch
*2 Adjustment Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

i.

Select "L" on the left/right select switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch.


iii.

Select "R" on the left/right select switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retractable Mirror)

a.

Check the mirror select switch and mirror surface adjust switch.

i.
B254629E16
0.095,0.058 0.250,0.201 0.155,0.142 10 *a 3.123,4.171 3.358,4.316 0.236,0.145 10 HR 2.642,4.171 2.868,4.316 0.226,0.145 10 VR 2.281,4.171 2.470,4.316 0.189,0.145 10 VL 1.849,4.171 2.066,4.316 0.217,0.145 10 HL 1.439,4.171 1.654,4.316 0.215,0.145 10 M+ 0.572,4.171 0.805,4.316 0.233,0.145 10 MR 0.235,4.171 0.460,4.316 0.225,0.145 10 MF 1.219,4.171 1.330,4.316 0.111,0.145 10 E 0.981,4.171 1.096,4.316 0.116,0.145 10 B 1.711,3.695 1.923,4.142 false 1.594,3.692 1.556,4.154 false 1.484,3.688 1.278,4.154 false 1.382,3.694 1.042,4.154 false 1.281,3.694 0.703,4.154 false 1.168,3.694 0.368,4.154 false 1.817,3.695 2.351,4.154 false 1.926,3.689 2.715,4.154 false 2.037,3.689 3.171,4.154 false 1.555,0.866 1.555,0.342 1.555,0.342 1.377,0.342 false 1.172,0.253 1.328,0.395 0.156,0.142 10 *1 1.714,1.876 1.714,2.38 1.714,2.38 1.981,2.38 false 2.032,2.307 2.188,2.449 0.156,0.142 10 *2

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Mirror select switch
*2 Mirror surface adjust switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

Standard Resistance (for left side):
Tester Connection Switch Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Switch Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch.

i.
B254629E05
0.095,0.058 0.250,0.201 0.155,0.142 10 *a 0.813,4.154 1.046,4.299 0.233,0.145 10 MR 0.407,4.154 0.632,4.299 0.225,0.145 10 MF 1.528,4.154 1.639,4.299 0.111,0.145 10 E 1.187,4.154 1.302,4.299 0.116,0.145 10 B 1.484,3.688 1.576,4.154 false 1.382,3.694 1.257,4.154 false 1.281,3.694 1.001,4.154 false 1.168,3.694 0.551,4.154 false 2.027,0.85 2.027,0.387 2.027,0.387 2.211,0.387 false 2.252,0.307 2.412,0.454 0.161,0.147 10 *1

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*1 Mirror retract switch
*a Component without harness connected
(Outer Mirror Switch Assembly)

Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (MF) - 7 (E) Mirror retract switch retract position Below 1 Ω
9 (MR) - 8 (B) Below 1 Ω
10 (MF) - 8 (B) Mirror retract switch return position Below 1 Ω
9 (MR) - 7 (E) Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.