Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM2170E _59 Vehicle Exterior _057048 WIPER / WASHER _0278177 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LHD)

a.
U159628E01
0.071,0.027 0.268,0.211 0.198,0.184 10 *a 0.254,1.185 0.555,1.347 0.301,0.163 10 G14 0.404,0.737 0.611,0.900 0.208,0.163 10 +2 0.752,0.474 0.959,0.637 0.208,0.163 10 +1 1.289,0.474 1.497,0.637 0.208,0.163 10 +B 1.683,0.474 1.891,0.637 0.208,0.163 10 +S 2.315,1.892 2.627,2.055 0.313,0.163 10 C1R 1.868,1.892 2.180,2.055 0.313,0.163 10 +1R 1.392,1.892 1.659,2.055 0.266,0.163 10 WR 2.119,0.474 2.390,0.637 0.271,0.163 10 WF 2.64,0.474 2.911,0.637 0.271,0.163 10 EW 2.889,1.185 3.188,1.347 0.299,0.163 10 G12 2.282,1.075 2.627,0.655 false 2.078,1.079 2.207,0.655 false 1.171,1.08 0.901,0.655 false 1.431,1.076 1.431,0.655 false 1.623,1.086 1.76,0.655 false 0.951,1.107 0.635,0.851 false 2.204,1.387 2.481,1.87 false 2.074,1.413 2.074,1.875 false 1.628,1.421 1.536,1.867 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
G14-1 (+S) - G14-3 (+1) OFF Below 1 Ω
INT
G14-2 (+B) - G14-3 (+1) MIST
LO
G14-2 (+B) - G14-4 (+2) HI

Front Washer Switch:
Tester Connection Switch Condition Specified Condition
G12-2 (EW) - G12-3 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Wiper Switch:
Tester Connection Switch Condition Specified Condition
G12-6 (C1R) - G12-2 (EW) OFF 10 kΩ or higher
G12-7 (+1R) - G12-2 (EW)
G12-6 (C1R) - G12-2 (EW) INT Below 1 Ω
G12-7 (+1R) - G12-2 (EW) HI Below 1 Ω

Rear Washer Switch:
Tester Connection Switch Condition Specified Condition
G14-5 (WR) - G12-2 (EW) OFF 10 kΩ or higher
G12-7 (+1R) - G12-2 (EW)
G14-5 (WR) - G12-2 (EW) WASH Below 1 Ω
G14-5 (WR) - G12-2 (EW) ON + WASH Below 1 Ω
G12-7 (+1R) - G12-2 (EW)


Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)

If the result is not as specified, replace the windshield wiper switch assembly.


b.

Check the intermittent operation.

i.

Connect a voltmeter positive (+) lead to terminal G14-3 (+1) and a negative (-) lead to terminal G12-2 (EW).


ii.

Connect an auxiliary battery positive (+) lead to terminal G14-2 (+B) and a negative (-) lead to terminal G12-2 (EW) and G14-1 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect an auxiliary battery positive (+) lead to terminal G14-1 (+S) for 5 seconds.


v.

Connect an auxiliary battery negative (-) lead to terminal G14-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals G14-3 (+1) and G12-2 (EW).

OK:

Voltage changes as shown in the illustration.


E056399E62
0.133,0.084 0.337,0.254 0.205,0.170 10 *a 1.734,0.549 2.453,0.700 0.719,0.151 10 10 to 14 V 2.2,1.028 2.474,1.184 0.274,0.156 10 0 V 2.484,1.463 3.642,1.627 1.158,0.164 10 1.6 +/- 1 seconds 2.699,0.205 2.896,0.366 0.197,0.161 10 *b 4.741,0.205 4.933,0.374 0.192,0.170 10 *c 4.625,1.454 5.884,1.610 1.259,0.155 10 10.7 +/- 5 seconds

If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*a Voltage between terminals G14-3 (+1) and G12-2 (EW) *b FAST: Connect auxiliary battery negative lead to terminal G14-1 (+S)
*c SLOW: Connect auxiliary battery negative lead to terminal G14-1 (+S) - -



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RHD)

a.
U183718E01
0.089,0.037 0.307,0.210 0.218,0.172 10 *a 0.299,1.003 0.581,1.166 0.282,0.163 10 G11 2.957,0.349 3.164,0.512 0.208,0.163 10 +2 2.501,0.349 2.709,0.512 0.208,0.163 10 +1 2.045,0.349 2.253,0.512 0.208,0.163 10 +B 1.59,0.349 1.797,0.512 0.208,0.163 10 +S 2.849,1.003 3.130,1.166 0.280,0.163 10 G13 0.418,0.349 0.731,0.512 0.313,0.163 10 EW 1.004,0.349 1.317,0.512 0.313,0.163 10 WF 1.014,1.785 1.296,1.948 0.282,0.163 10 +1R 1.982,1.785 2.264,1.948 0.282,0.163 10 WR 2.236,1.096 2.594,0.529 false 2.024,1.096 2.171,0.529 false 1.825,1.097 1.709,0.529 false 1.425,1.096 1.133,0.529 false 1.21,1.096 0.571,0.529 false 1.793,1.383 2.071,1.744 false 1.428,1.383 1.203,1.785 false 0.549,1.785 0.851,1.948 0.301,0.163 10 C1R 1.256,1.383 0.762,1.785 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Front Wiper Switch
Tester Connection Switch Condition Specified Condition
G13-4 (+S) - G13-2 (+1) OFF Below 1 Ω
INT
G13-3 (+B) - G13-2 (+1) MIST
LO
G13-3 (+B) - G13-1 (+2) HI

Front Washer Switch:
Tester Connection Switch Condition Specified Condition
G11-2 (EW) - G11-1 (WF) ON Below 1 Ω
OFF 10 kΩ or higher

Rear Wiper Switch:
Tester Connection Switch Condition Specified Condition
G11-5 (C1R) - G11-2 (EW) OFF 10 kΩ or higher
G11-4 (+1R) - G11-2 (EW)
G11-5 (C1R) - G11-2 (EW) INT Below 1 Ω
G11-4 (+1R) - G11-2 (EW) HI Below 1 Ω

Rear Washer Switch:
Tester Connection Switch Condition Specified Condition
G13-10 (WR) - G11-2 (EW) OFF 10 kΩ or higher
G11-4 (+1R) - G11-2 (EW)
G13-10 (WR) - G11-2 (EW) WASH Below 1 Ω
G13-10 (WR) - G11-2 (EW) ON + WASH Below 1 Ω
G11-4 (+1R) - G11-2 (EW)


Text in Illustration
*a Component without harness connected
(Windshield Wiper Switch Assembly)

If the result is not as specified, replace the windshield wiper switch assembly.


b.

Check the intermittent operation.

i.

Connect a voltmeter positive (+) lead to terminal G13-2 (+1) and a negative (-) lead to terminal G11-2 (EW).


ii.

Connect an auxiliary battery positive (+) lead to terminal G13-3 (+B) and a negative (-) lead to terminal G11-2 (EW) and G13-4 (+S).


iii.

Turn the wiper switch to the INT position.


iv.

Connect an auxiliary battery positive (+) lead to terminal G13-4 (+S) for 5 seconds.


v.

Connect an auxiliary battery negative (-) lead to terminal G13-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals G13-2 (+1) and G11-2 (EW).

OK:

Voltage changes as shown in the illustration.


E056399E62
0.133,0.084 0.337,0.254 0.205,0.170 10 *a 1.734,0.549 2.453,0.700 0.719,0.151 10 10 to 14 V 2.2,1.028 2.474,1.184 0.274,0.156 10 0 V 2.484,1.463 3.642,1.627 1.158,0.164 10 1.6 +/- 1 seconds 2.699,0.205 2.896,0.366 0.197,0.161 10 *b 4.741,0.205 4.933,0.374 0.192,0.170 10 *c 4.625,1.454 5.884,1.610 1.259,0.155 10 10.7 +/- 5 seconds

If the result is not as specified, replace the windshield wiper switch assembly.

Text in Illustration
*a Voltage between terminals G13-2 (+1) and G11-2 (EW) *b FAST: Connect auxiliary battery negative lead to terminal G13-4 (+S)
*c SLOW: Connect auxiliary battery negative lead to terminal G13-4 (+S) - -