Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Headlight) › 2014.12–2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278187 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  DISASSEMBLY  


PROCEDURE

Hide 85662 1.REMOVE HEADLIGHT LEVELING MOTOR

a.
E308379N02
1.76,1.031 2.625,0.927 false 2.281,1.677 2.479,1.854 0.198,0.177 10 false 2 1.073,1.135 1.271,1.313 0.198,0.177 10 false 1 2.677,0.854 2.875,1.031 0.198,0.177 10 true *a

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.

Text in Illustration
*a Aiming Screw

HINT:
·

Turn the aiming screw until the headlight leveling motor can be moved in the direction indicated by the arrow (2) shown in the illustration.

·

Make sure to remember the number of aiming screw rotations.




b.

Turn the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to disengage the pin.

HINT:

When removing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction indicated by the arrow (2) shown in the illustration.



c.
E308381N03
1.646,0.958 2.365,0.823 false 1.49,1.688 1.698,1.854 0.208,0.167 10 false 4 0.948,1 1.177,1.177 0.229,0.177 10 false 3 2.396,0.729 2.646,0.938 0.25,0.208 10 true *a

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration to disengage the shaft.

Text in Illustration
*a Aiming Screw

HINT:

Make sure to remember the number of aiming screw rotations.



d.

Pull out the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to remove it.


Hide 85669 2.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Remove the headlight leveling motor base packing.

NOTICE:

After the headlight leveling motor base packing is removed, be sure to replace it with a new one. Failure to do this may cause water ingress.



Hide 81139 3.REMOVE HEADLIGHT SOCKET COVER

a.
E308840

Turn the headlight socket cover as shown in the illustration to remove it.


Hide 81171B 4.REMOVE HEADLIGHT LENS

a.
E412544

Disconnect the connector.


b.
E308384N01
0.063,1.563 0.26,1.729 0.198,0.167 10 false *a 0.323,0.052 0.542,0.24 0.219,0.188 10 false *a 2.521,0.385 2.74,0.573 0.219,0.188 10 false *a 3.104,1.229 3.302,1.396 0.198,0.167 10 false *a 1.5,1.552 1.719,1.74 0.219,0.188 10 true *b

Remove the 4 screws.

Text in Illustration
*a Screw
*b "TORX" Screw


c.

Using a T20H "TORX" driver, remove the "TORX" screw.


d.
E308385

Using a dryer, heat the backside of the headlight unit.

NOTICE:

If the headlight is heated unevenly, it will deform or melt.



e.
E308386

Disengage the 8 claws and remove the headlight lens.

NOTICE:
·

Wear rubber gloves when handling the headlight lens.

·

Do not touch the lens or the aluminum surfaces with bare hands.

·

If there are fingerprints on the aluminum surfaces, wipe them off with a soft cloth.

·

If there are fingerprints on the back of the headlight lens, replace the headlight lens.

·

Do not allow dirt or foreign matter to get on the headlight lens.



HINT:

If the lens cannot be removed even after heating, using a screwdriver with its tip wrapped in tape, lift the lens. Be careful not to damage the headlight lens and housing.



Hide 81132B 5.REMOVE HEADLIGHT LENS GASKET

a.

Remove the headlight lens gasket from the housing.


Hide 6.REMOVE HEADLIGHT LED UNIT

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight LED unit or other components.

·

If there are any fingerprints or foreign matter on the headlight LED unit or other components, wipe them off with a soft cloth.



a.
E424967

Disconnect the connector.


b.
E424968

Disengage the 2 claws.


c.

Turn the aiming screw in the direction indicated by the arrow shown in the illustration, and remove the headlight LED unit from the housing.

HINT:

Make sure to remember the number of aiming screw rotations.