Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Halogen Headlight) › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278188 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  DISASSEMBLY  


PROCEDURE

Hide 81110B 1.REMOVE NO. 1 HEADLIGHT BULB

a.
E237667

Turn the No. 1 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

NOTICE:

Do not touch the bulb glass.



Hide 81110D 2.REMOVE NO. 2 HEADLIGHT BULB

a.
E237669

Turn the No. 2 headlight bulb in the direction indicated by the arrow shown in the illustration, and remove it.

NOTICE:

Do not touch the bulb glass.



Hide 81610F 3.REMOVE CLEARANCE LIGHT BULB

a.
E237671

Turn the clearance light socket with the clearance light bulb in the direction indicated by the arrow shown in the illustration, and remove them as a unit.


b.

Remove the clearance light bulb from the clearance light socket.


Hide 85662 4.REMOVE HEADLIGHT LEVELING MOTOR

a.
E237673E02
1.583,1.344 2.156,1.021 false 1.042,1.26 1.24,1.438 0.198,0.177 10 true (1) 2.104,1.917 2.302,2.094 0.198,0.177 10 false (2) 2.167,0.917 2.365,1.094 0.198,0.177 10 true *1

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.

Text in Illustration
*1 Aiming Screw

HINT:
·

Turn the aiming screw until the headlight leveling motor can be moved in the direction indicated by the arrow (2) shown in the illustration.

·

Make sure to remember the number of aiming screw rotations.




b.

Turn the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to disengage the pin.

HINT:

When removing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction indicated by the arrow (2) shown in the illustration.



c.
E237675E02
1.583,1.344 2.156,1.021 false 1.052,1.302 1.25,1.479 0.198,0.177 10 true (3) 1.479,1.917 1.677,2.094 0.198,0.177 10 false (4) 2.167,0.917 2.365,1.094 0.198,0.177 10 true *1

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration to disengage the shaft.

Text in Illustration
*1 Aiming Screw

HINT:

Make sure to remember the number of aiming screw rotations.



d.

Pull out the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to remove it.


Hide 85669 5.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Remove the headlight leveling motor base packing.

NOTICE:

After the headlight leveling motor base packing is removed, be sure to replace it with a new one. Failure to do this may cause water ingress.



Hide 81171B 6.REMOVE HEADLIGHT LENS

a.
E237688E04
0.563,1.896 0.719,2.052 0.156,0.156 10 false *1 0.104,0.229 0.26,0.385 0.156,0.156 10 false *1 2.625,0.708 2.781,0.865 0.156,0.156 10 false *1 3.094,1.198 3.25,1.354 0.156,0.156 10 false *1 1.813,1.573 1.969,1.729 0.156,0.156 10 true *2

Remove the 4 screws.

Text in Illustration
*1 Screw
*2 "TORX" Screw


b.

Using a T20H "TORX" driver, remove the "TORX" screw.


c.
E237689

Using a dryer, heat the backside of the headlight unit.

NOTICE:

If the headlight is heated unevenly, it will deform or melt.



d.
E237691

Disengage the 8 claws and remove the headlight lens.

NOTICE:
·

Wear rubber gloves when handling the headlight lens.

·

Do not touch the lens or the aluminum surfaces with bare hands.

·

If there are fingerprints on the aluminum surfaces, wipe them off with a soft cloth.

·

If there are fingerprints on the back of the headlight lens, replace the headlight lens.

·

Do not allow dirt or foreign matter to get on the headlight lens.



HINT:

If the lens cannot be removed even after heating, using a screwdriver with its tip wrapped in tape, lift the lens. Be careful not to damage the headlight lens and housing.



Hide 81132B 7.REMOVE HEADLIGHT LENS GASKET

a.

Remove the headlight lens gasket from the housing.