Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › 2011.12–2019.07
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278195 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM U

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  TERMINALS OF ECU  


CHECK HEADLIGHT LEVELING ECU ASSEMBLY


a.

Disconnect the A34 headlight leveling ECU assembly connector.

U181950N01
3.5,0.24 3.958,0.51 0.458,0.271 10 false A34


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A34-1 (IG) - Body ground V - Body ground IG power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V

Standard Resistance
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A34-9 (E1) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the A34 headlight leveling ECU assembly connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A34-21 (SGR) - Body ground R - Body ground Rear height control sensor ground Always Below 1 Ω
A34-23 (RH-) - Body ground L - Body ground Leveling motor RH ground Always Below 1 Ω
A34-24 (LH-) - Body ground L - Body ground Leveling motor LH ground Always Below 1 Ω

Standard Voltage
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A34-3 (HDLP) - Body ground BR - Body ground Low beam headlight signal input Low beam headlights on Below 1.5 V
Low beam headlights off 5 V or higher
A34-5 (INIT) - Body ground G - Body ground Initialization signal input Terminals LVL and GND of DLC3 connected Below 1 V
Terminals LVL and GND of DLC3 not connected 4.5 to 5.5 V
A34-6 (WNG) - Body ground SB - Body ground Warning indicator drive output Warning indicator on Below 1 V
Warning indicator off 11 to 14 V
A34-10 (RH+) - Body ground R - Body ground Leveling motor RH power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A34-11 (LH+) - Body ground G - Body ground Leveling motor LH power supply Power switch off Below 1 V
Power switch on (IG) 11 to 14 V
A34-12 (SBR) - Body ground P - Body ground Rear height control sensor power supply Power switch off Below 1 V
Power switch on (IG) 4.75 to 5.25 V
A34-16 (SPDR) - Body ground GR - Body ground Vehicle speed signal input Vehicle driven at approx. 20 km/h (12mph) Pulse generation
(See waveform 1)
A34-17 (RHT) - Body ground G - Body ground Leveling motor RH operation signal input With low beam headlights on, vehicle height not changed Below 1 V
With low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1.0 to 14.4 V
A34-18 (LHT) - Body ground R - Body ground Leveling motor LH operation signal input With low beam headlights on, vehicle height not changed Below 1 V
With low beam headlights on, vehicle height changed and maintained for more than 3 seconds 1.0 to 14.4 V
A34-19 (SHRL) - Body ground G - Body ground Rear height control sensor signal input Power switch off Below 1 V
Power switch on (IG) 0.5 to 4.5 V*1

*1: The value is changed by the vehicle condition.


If the result is not as specified, the headlight leveling ECU assembly may have a malfunction.

i.
E149152E01
2.806,1.183 3.146,1.325 0.340,0.142 10 GND

Waveform 1

Item Content
Tool setting 2 V/DIV., 2 ms./DIV.
Vehicle condition Wheel being rotated