Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › 2014.12–2015.11
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278195 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM J

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  Speed Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly receives the vehicle speed signal from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E237350E10
0.073,2.188 4.26,2.396 4.188,0.208 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 0.854,1.219 1.146,1.365 0.292,0.146 10 false SP1 0.073,2.031 0.396,2.208 0.323,0.177 10 false A41 1.229,1.219 1.417,1.365 0.188,0.146 10 false 11 0.688,3.396 2.51,3.781 1.823,0.385 10 false Certification ECU (Smart Key ECU Assembly) 0.354,3.406 0.969,3.573 0.615,0.167 10 false G79 1.708,3 2.052,3.156 0.344,0.156 10 false SPD 2.115,3 2.292,3.156 0.177,0.156 10 false 27 2.896,2.906 3.073,3.063 0.177,0.156 10 false 37 4.01,2.906 4.188,3.063 0.177,0.156 10 false 15 4,4.677 4.177,4.833 0.177,0.156 10 false 16 2.885,4.667 3.063,4.823 0.177,0.156 10 false 40 2.875,4.885 3.208,5.042 0.333,0.156 10 false 3C 2.885,3.094 3.219,3.25 0.333,0.156 10 false 3A 4.01,3.094 4.344,3.25 0.333,0.156 10 false 3B 4,4.875 4.333,5.031 0.333,0.156 10 false 3A 5.344,1.229 5.646,1.375 0.302,0.146 10 false 40 5.333,2.99 5.604,3.135 0.271,0.146 10 false 39 5.594,1.281 5.792,1.427 0.198,0.146 10 false SI 5.594,3.073 5.792,3.219 0.198,0.146 10 false +S 5,3.448 5.271,3.594 0.271,0.146 10 false G1 5.25,3.448 7.083,3.75 1.833,0.302 10 false Combination Meter Assembly 5.604,4.76 5.927,4.906 0.323,0.146 10 false SPD 5.344,4.76 5.656,4.927 0.313,0.167 10 false 17 4.969,5.177 5.302,5.333 0.333,0.156 10 false G41 5.302,5.177 7.052,5.354 1.75,0.177 10 false Radio Receiver Assembly*1 2.948,5.781 4.167,5.948 1.219,0.167 10 false Junction Connector 2.115,4.75 2.427,4.917 0.313,0.167 10 false 16 0.656,5.188 1.25,5.344 0.594,0.156 10 false A34 0.958,5.188 2.271,5.51 1.313,0.323 10 false Headlight Leveling ECU Assembly*2 1.635,4.75 2.115,4.896 0.479,0.146 10 false SPDR 3.375,6.677 5.708,6.854 2.333,0.177 10 false *1: w/ Audio and Visual System 3.375,7.052 6.906,7.229 3.531,0.177 10 false *2: for LED Headlight

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / HL Auto Leveling / Data List.


e.

Read the display on the intelligent tester.

HL Auto Leveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -

OK:

Normal condition listed above is displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
U183366E02
0.865,1.417 0.667,1.917 false 1.135,3.896 1.385,3.896 false 1.073,3.708 1.073,4.031 false 1.448,3.708 1.448,4.031 false 0.135,0.115 0.292,0.271 0.156,0.156 10 false *a 0.552,1.948 0.781,2.104 0.229,0.156 10 false +S 2.771,3.656 3.094,3.813 0.323,0.156 10 false GND 1.146,3.927 1.354,4.083 0.208,0.156 10 false (A) 1.625,0.479 1.927,0.635 0.302,0.156 10 false G1

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G1-39 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms/DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is displayed as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G1 combination meter assembly connector.


b.

Disconnect the A34 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-16 (SPDR) - G1-39 (+S) Always Below 1 Ω




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR