Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM › 2014.12–2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278195 AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM D

LIGHTING (EXT)  AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM  INITIALIZATION  


NOTICE:
·

Initialize the headlight leveling ECU assembly when the headlight leveling ECU assembly is replaced.

·

Initialize the headlight leveling ECU assembly (set the zero point of the height control sensor in the headlight leveling ECU assembly) after the vehicle height changes due to replacement of suspension components or after performing operations such as removal and reinstallation or replacement of the rear height control sensor sub-assembly.

·

Adjust the headlight aim after initializing the headlight leveling ECU assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>ADJUSTMENT).

·

When a malfunction is detected in the automatic headlight beam level control system, height control sensor signal initialization is impossible. Perform troubleshooting before initialization.



1.PREPARE VEHICLE FOR INITIALIZATION


a.

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.


b.

Check that there are no occupants in the vehicle.


c.

Turn off the headlights.


d.

Stop the vehicle on a level surface and keep the vehicle height unchanged.

Result:
Proceed to
NEXT




2.CHECK HEADLIGHT LEVELING WARNING


a.

Turn the power switch on (IG), and check the headlight leveling warning.

OK:
Condition Specified Condition
The headlight leveling ECU assembly has been replaced with a new one. Headlight leveling warning repeatedly blinks 6 times at 2 Hz.
Replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc. have been performed. Headlight leveling warning is not displayed.


HINT:

If the indicator light does not come on when turning the power switch on (IG), inspect and repair it according to Problem Symptoms Table (See page Vehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).


Result:
Result Proceed to
OK GO TO STEP 3
NG GO TO PROBLEM SYMPTOMS TABLE




3.INITIALIZATION


a.
E106867E45
1.425,0.119 1.685,0.294 0.260,0.175 10 CG 0.061,0.016 0.496,0.191 0.435,0.175 10 DLC3: 2.896,0.62 3.162,0.790 0.266,0.170 10 LVL 2.269,0.715 2.83,0.715 false 1.558,0.726 1.558,0.309 false

Connect SST to terminals 4 (CG) and 8 (LVL) of the DLC3.


b.
SST
09843-18040  


c.
E233303E02
1.021,2.729 1.323,2.927 0.302,0.198 10 A 1.01,0.729 1.271,0.906 0.26,0.177 10 E 1.01,1.25 1.302,1.438 0.292,0.188 10 D 1.01,2.344 1.365,2.521 0.354,0.177 10 B 1,1.854 1.313,2.042 0.313,0.188 10 C

Turn the low beam headlights on and off using the light control switch within 20 seconds after connecting the terminals.

HINT:

The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.

Fuel Level Number of Times to Turn Low Beam Headlights On and Off
Fuel level is within A range. 1
Fuel level is within B range. 2
Fuel level is within C range. 3
Fuel level is within D range. 4
Fuel level is within E range. 5


NOTICE:
·

Turn the low beam headlights on and off at less than 3-second intervals.

·

Be sure to operate the light control switch from outside the vehicle.




d.

Check the headlight leveling warning.

OK:
Condition Specified Condition
The headlight leveling ECU assembly has been replaced with a new one. Blinks 6 times at 2 Hz → Repeatedly blinks N*1 times at 2 Hz.
Replacement of the rear height control sensor sub-assembly, removal and reinstallation of the rear height control sensor sub-assembly, replacement of the suspension, etc. have been performed. Off → Repeatedly blinks N*1 times at 2 Hz.


HINT:
·

*1: The number of times that the headlight leveling warning is determined by the number of times the low beam headlights are turned on and off.

·

If initialization does not finish normally, disconnect SST from the DLC3 and turn the power switch off. Then, restart initialization from step 1.



Result:
Result Proceed to
OK TURN POWER SWITCH OFF (END)
NG GO TO PROBLEM SYMPTOMS TABLE