Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Turn Signal Switch Circuit  


DESCRIPTION

The combination meter receives the turn signal switch information and controls the turn signal lights.

WIRING DIAGRAM

E224250E46
5.229,3.771 7.125,4.156 1.896,0.385 10 false Combination Meter Assembly 0.802,3.958 3.365,4.219 2.563,0.26 10 false Headlight Dimmer Switch Assembly 5.521,1.125 5.771,1.375 0.25,0.25 10 false 9 5.479,1.552 5.844,1.844 0.365,0.292 10 false 10 5.729,1.24 6.104,1.469 0.375,0.229 10 false ER 5.729,1.656 6.042,1.885 0.313,0.229 10 false EL 1.938,2.854 2.292,3.063 0.354,0.208 10 false N 1.854,2.615 2.302,2.917 0.448,0.302 10 false RLC 1.938,2.385 2.271,2.604 0.333,0.219 10 false R 1.938,3.333 2.271,3.542 0.333,0.208 10 false L 1.865,3.094 2.365,3.333 0.5,0.24 10 false LLC 2.927,2.146 3.24,2.406 0.313,0.26 10 false TL 3.323,1.552 3.667,1.917 0.344,0.365 10 false TL 2.604,2.146 2.958,2.365 0.354,0.219 10 false TR 3.323,1.125 3.667,1.417 0.344,0.292 10 false TR 3.333,0.604 3.677,0.833 0.344,0.229 10 false EL 3.583,1.542 3.99,1.833 0.406,0.292 10 false 18*2 3.583,1.125 3.917,1.396 0.333,0.271 10 false 16*2 3.573,0.594 4.094,0.906 0.521,0.313 10 false 19*2 2.313,2.146 2.635,2.396 0.323,0.25 10 false EL 0.74,2.521 1.688,3.01 0.948,0.49 10 false Turn Signal 5.229,3.594 5.479,3.771 0.25,0.177 10 false G3 0.792,3.792 1.698,4.031 0.906,0.24 10 false G10*1, G9*2 3.552,4.271 4.292,4.521 0.74,0.25 10 false *1: for LHD 4.49,4.271 5.208,4.521 0.719,0.25 10 false *2: for RHD 3.573,0.438 4.229,0.74 0.656,0.302 10 false 12*1 3.583,0.979 3.917,1.25 0.333,0.271 10 false 13*1 3.583,1.396 3.99,1.688 0.406,0.292 10 false 15*1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the display on the intelligent tester.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Turn Signal Switch (Right) Turn signal switch (Right) signal/ON or OFF ON: Turn signal switch (Right) on
OFF: Turn signal switch (Right) off
-
Turn Signal Switch (Left) Turn signal switch (Left) signal/ON or OFF ON: Turn signal switch (Left) on
OFF: Turn signal switch (Left) off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
a.

Remove the headlight dimmer switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>REMOVAL).


b.
E223779E20
0.063,0.049 0.242,0.229 0.179,0.180 10 *a 1.455,1.836 1.642,1.996 0.187,0.161 10 TL 1.84,1.39 1.588,1.833 false 2.212,1.836 2.420,1.996 0.208,0.161 10 TR 2.696,1.836 2.917,1.996 0.221,0.161 10 EL 2.366,1.39 2.764,1.833 false 2.194,1.39 2.32,1.833 false

for LHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (TR) - 12 (EL) Turn signal switch in neutral position 10 kΩ or higher
15 (TL) - 12 (EL) Turn signal switch in neutral position 10 kΩ or higher
13 (TR) - 12 (EL) Turn signal switch in right turn position Below 1 Ω
15 (TL) - 12 (EL) Turn signal switch in left turn position Below 1 Ω


Text in Illustration
*a Component without harness connected
(Headlight Dimmer Switch Assembly)



c.
E223779E23
0.063,0.049 0.242,0.229 0.179,0.180 10 *a 1.3,1.836 1.487,1.996 0.187,0.161 10 TL 1.288,1.394 1.382,1.833 false 1.662,1.836 1.870,1.996 0.208,0.161 10 TR 0.84,1.836 1.061,1.996 0.221,0.161 10 EL 1.068,1.393 0.908,1.833 false 1.644,1.39 1.77,1.833 false

for RHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
16 (TR) - 19 (EL) Turn signal switch in neutral position 10 kΩ or higher
18 (TL) - 19 (EL) Turn signal switch in neutral position 10 kΩ or higher
16 (TR) - 19 (EL) Turn signal switch in right turn position Below 1 Ω
18 (TL) - 19 (EL) Turn signal switch in left turn position Below 1 Ω


Text in Illustration
*a Component without harness connected
(Headlight Dimmer Switch Assembly)




OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G3 combination meter assembly connector.


b.

for LHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-13 (TR) - G3-9 (ER) Always Below 1 Ω
G10-15 (TL) - G3-10 (EL) Always Below 1 Ω
G10-12 (EL) - Body ground Always Below 1 Ω
G3-9 (ER) - Body ground Always 10 kΩ or higher
G3-10 (EL) - Body ground Always 10 kΩ or higher




c.

for RHD

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-16 (TR) - G3-9 (ER) Always Below 1 Ω
G9-18 (TL) - G3-10 (EL) Always Below 1 Ω
G9-19 (EL) - Body ground Always Below 1 Ω
G3-9 (ER) - Body ground Always 10 kΩ or higher
G3-10 (EL) - Body ground Always 10 kΩ or higher





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR