Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER(w/o Wheel Opening Moulding) › 2011.12–2014.12
RM2170E _59 Vehicle Exterior _057051 EXTERIOR PANELS / TRIM _0278207 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


PROCEDURE

Hide 52131A 1.INSTALL FRONT BUMPER REINFORCEMENT

a.
B310563

Install the front bumper reinforcement with the 6 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


b.

Engage the 2 clamps and install the wire harness.


Hide 52611 2.INSTALL FRONT BUMPER ENERGY ABSORBER

a.
B310562

Engage the 2 guides to install the front bumper energy absorber.


Hide 53288B 3.INSTALL RADIATOR SUPPORT EXTENSION LH

a.
B307340

Engage the 2 claws and install the radiator support extension LH.


b.

Engage the 2 clamps to install the thermistor assembly.


Hide 53287B 4.INSTALL RADIATOR SUPPORT EXTENSION RH

a.
B307341

Engage the 2 claws and install the radiator support extension RH.


Hide 53286B 5.INSTALL NO. 2 RADIATOR SIDE AIR SEAL

a.
B307338

Engage the 2 claws and install the No. 2 radiator side air seal.


Hide 53285B 6.INSTALL NO. 1 RADIATOR SIDE AIR SEAL

a.
B307339

Engage the 2 claws and install the No. 1 radiator side air seal.


Hide 53289A 7.INSTALL RADIATOR SUPPORT OPENING COVER

a.
B297147

Install the radiator support opening cover with the 6 clips.


Hide 52536 8.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B310558

Engage the claw.


b.

Install the front bumper side retainer LH with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 52535 9.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 52127C 10.INSTALL FRONT BUMPER HOLE COVER

a.
B297137

Engage the 2 claws and install the front bumper hole cover.


Hide 53112E 11.INSTALL LOWER NO. 1 RADIATOR GRILLE

a.
B297136

Engage the 16 claws and install the lower No. 1 radiator grille.


Hide 53111 12.INSTALL RADIATOR GRILLE

a.
B297135

Engage the 12 claws and install the radiator grille.


Hide 75311 13.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.
B297138

Engage the 2 guides and 4 claws, and install the radiator grille (or front panel) emblem.


b.

Install the 2 screws.


Hide 52521B 14.INSTALL UPPER FRONT BUMPER RETAINER

a.
B297133

Install the upper front bumper retainer with the 4 clips.


Hide 53395E 15.INSTALL HOOD TO FRONT END PANEL SEAL

a.

Clean the attachment surface.

i.

Remove the double-sided tape from the front bumper cover.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Install the hood to front end panel seal.

i.

Remove the release paper from the face of the hood to front end panel seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



ii.
B297134

Install a new hood to front end panel seal as shown in the illustration.

NOTICE:

Thoroughly press the hood to front end panel seal to ensure that it adheres.



iii.

Install the 3 clips.



Hide 81482C 16.INSTALL FOG LIGHT COVER LH

a.
B297132

Engage the 6 claws and install the fog light cover LH.


Hide 81481E 17.INSTALL FOG LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 81210A 19.INSTALL FOG LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81520 20.INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH

Hide 81510 21.INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 52114A 22.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

a.
B310574

Engage the 2 claws.


b.

Install the front bumper extension mounting bracket with the 2 screws.


Hide 23.INSTALL HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)

a.
B297131

Engage the 7 clamps to install the headlight cleaner hose.


Hide 85208A 24.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

Hide 85207A 25.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

Hide 85341A 26.INSTALL HEADLIGHT CLEANER WASHER NOZZLE COVER (w/ Headlight Cleaner System)