Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER(w/o Wheel Opening Moulding) › 2014.12–2017.06
RM2170E _59 Vehicle Exterior _057051 EXTERIOR PANELS / TRIM _0278207 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REASSEMBLY  


PROCEDURE

Hide 52131A 1.INSTALL FRONT BUMPER REINFORCEMENT

a.
B310563

Install the front bumper reinforcement with the 6 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


b.

Engage the 2 clamps and install the wire harness.


Hide 52611 2.INSTALL FRONT BUMPER ENERGY ABSORBER

a.
B310562

Engage the 2 guides to install the front bumper energy absorber.


Hide 53288B 3.INSTALL RADIATOR SUPPORT EXTENSION LH

a.
B307340

Engage the 2 claws and install the radiator support extension LH.


b.

Engage the 2 clamps to install the thermistor assembly.


Hide 53287B 4.INSTALL RADIATOR SUPPORT EXTENSION RH

a.
B307341

Engage the 2 claws and install the radiator support extension RH.


Hide 53286B 5.INSTALL NO. 2 RADIATOR SIDE AIR SEAL

a.
B307338

Engage the 2 claws and install the No. 2 radiator side air seal.


Hide 53285B 6.INSTALL NO. 1 RADIATOR SIDE AIR SEAL

a.
B307339

Engage the 2 claws and install the No. 1 radiator side air seal.


Hide 53289A 7.INSTALL RADIATOR SUPPORT OPENING COVER

a.
B391888

Install the radiator support opening cover with the 4 clips.


Hide 52536 8.INSTALL FRONT BUMPER SIDE RETAINER LH

a.
B391887

Engage the 2 claws.


b.
B391886

Install the front bumper side retainer LH with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 52535 9.INSTALL FRONT BUMPER SIDE RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 53141C 10.INSTALL RADIATOR GRILLE GARNISH

a.

Engage the 2 guides and 23 claws to install the radiator grille garnish.

B391911


b.
B391910

Install the 2 screws.


Hide 52127C 11.INSTALL FRONT BUMPER HOLE COVER

a.
B391883E10
1.885,2.333 1.667,2.677 true 1.49,2.677 1.677,2.865 0.188,0.188 10 true *a

Engage the hook.

Text in Illustration
*a Hook


b.

Engage the guide and 2 claws to install the front bumper hole cover.


Hide 53122B 12.INSTALL NO. 2 RADIATOR GRILLE MOULDING

a.
B391882E06
0.917,1.208 1.24,0.938 true 0.729,1.156 0.917,1.333 0.188,0.177 10 true *a

Engage the hook.

Text in Illustration
*a Hook


b.

Engage the 2 claws to install the No. 2 radiator grille moulding.


Hide 53112E 13.INSTALL LOWER NO. 1 RADIATOR GRILLE

a.

Engage the 13 claws to install the lower No. 1 radiator grille.

B391908


Hide 75311 14.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

a.
B391902

Engage the 2 guides and 4 claws to install the radiator grille (or front panel) emblem.


b.

Install the 2 screws.


Hide 53111 15.INSTALL RADIATOR GRILLE

a.
B391901

Engage the 11 claws to install the radiator grille.


Hide 52521B 16.INSTALL UPPER FRONT BUMPER RETAINER

a.
B391909

Install the upper front bumper retainer with the 4 clips.


Hide 53395E 17.INSTALL HOOD TO FRONT END PANEL SEAL

a.

Clean the front bumper cover.

i.

Remove any remaining double-sided tape from the front bumper cover.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Remove the release paper from a new hood to front end panel seal.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



c.
B391877E06
0.604,0.604 0.813,0.75 false 0.833,0.688 1.021,0.865 0.188,0.177 10 false *a

Install the hood to front end panel seal as shown in the illustration.

Text in Illustration
*a Double-sided Tape

NOTICE:

Thoroughly press the hood to front end panel seal to ensure that it adheres.



d.

Install the 3 clips.


Hide 81482C 18.INSTALL FOG LIGHT COVER LH

a.
B391900

Engage the 4 claws to install the fog light cover LH.


Hide 81481E 19.INSTALL FOG LIGHT COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 81220 20.INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

Hide 81210A 21.INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:

Use the same procedure as for the LH side.


Hide 81520 22.INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH

Hide 81510 23.INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 52114A 24.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET

a.
B392319

Engage the 2 claws.


b.

Install the front bumper extension mounting bracket with the 2 screws.