Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.11–2019.07
RM2170E _59 Vehicle Exterior _057056 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0278228 VEHICLE PROXIMITY NOTIFICATION SYSTEM U

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  TERMINALS OF ECU  


CHECK VEHICLE APPROACHING SPEAKER CONTROLLER


U183684E02
3.5,0.302 3.833,0.469 0.333,0.167 10 false G85

a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G85-1 (IG) - Body ground LG - Body ground IG power supply Power switch on (IG) 11 to 14 V
Power switch off Below 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G85-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


d.

Reconnect the G85 vehicle approaching speaker controller connector.


e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G85-2 (STP) - G85-7 (GND) P - W-B Stop light signal input Power switch off, brake pedal depressed 8 V or higher
Power switch off, brake pedal released Below 1 V
G85-3 (SP+) - G85-8 (SP-) R - G Vehicle approaching speaker output Vehicle approaching speaker operating A waveform synchronized with the sound is output.
(See Waveform 1)
G85-5 (SW) - G85-7 (GND) P - W-B Vehicle approaching speaker switch signal Power switch on (IG), vehicle approaching speaker switch being pushed and held 6 V or higher
Power switch on (IG), vehicle approaching speaker switch not pushed Below 1 V
G85-6 (SPD) - G85-7 (GND) L - W-B Speed signal input Power switch on (IG), wheel being rotated Pulse generation
(See Waveform 2)
G85-9 (PRST) - G85-7 (GND) B - W-B SIL communication system Power switch on (IG), during transmission Pulse generation
(See Waveform 3)
G85-10 (IND) - G85-7 (GND) L - W-B Vehicle proximity notification off indicator light signal Power switch on (IG), vehicle proximity notification off indicator light off 11 to 14 V
Power switch on (IG), vehicle proximity notification off indicator light on Below 1.8 V
G85-11 (SFTP) - G85-7 (GND) G - W-B Transmission shift main switch signal input Power switch on (IG), shift lever in P 8 V or higher
Power switch on (IG), shift lever not in P Below 2.5 V
G85-12 (OPSW) - G85-7 (GND) GR - W-B Engine oil pressure switch signal input Idling* 8 V or higher
Power switch on (IG) Below 2 V

*: Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

If the result is not as specified, there is a problem in the vehicle approaching speaker controller or wire harness.

i.
E289167

Waveform 1

Item Condition
Tool setting 1 V/DIV., 200 ms./DIV.
Vehicle condition Vehicle approaching speaker operating


ii.
E267248E10
2.977,1.192 3.341,1.570 0.364,0.378 10 GND 1.144,1.647 1.283,1.806 0.139,0.159 10 A

Waveform 2

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Power switch on (IG), wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



iii.
E288729E04
0.146,1.594 0.604,1.792 0.458,0.198 10 false GND

Waveform 3

Item Condition
Tool setting 5 V/DIV., 10 ms./DIV.
Vehicle condition Power switch on (IG), during transmission