Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2015.11–2019.07
RM2170E _59 Vehicle Exterior _057056 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0278228 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  Proximity Notification Sound OFF Indicator does not Illuminate or Turn Off  


DESCRIPTION

When the vehicle approaching speaker switch is turned on, the vehicle approaching speaker controller receives a signal to temporarily suspend output of the vehicle approaching speaker assembly, and the vehicle approaching speaker switch illumination comes on.

WIRING DIAGRAM

E283306E03
0.448,1.094 0.76,1.292 0.313,0.198 10 false 3A 0.417,3.073 0.729,3.271 0.313,0.198 10 false G84 0.448,1.24 3.344,1.458 2.896,0.219 10 false Instrument Panel Junction Block Assembly 5.313,1.885 7.156,2.292 1.844,0.406 10 false Combination Meter Assembly 5.313,1.719 5.625,1.917 0.313,0.198 10 false G1 4.573,1.448 4.885,1.646 0.313,0.198 10 false IND 5.719,1.333 6.031,1.531 0.313,0.198 10 false 14 5.979,1.448 6.292,1.646 0.313,0.198 10 false IND 4.875,1.333 5.188,1.531 0.313,0.198 10 false 10 0.417,3.229 2.99,3.531 2.573,0.302 10 false Vehicle Approaching Speaker Switch 1.927,0.563 2.552,0.76 0.625,0.198 10 false GAUGE 0.552,0.438 1.521,0.823 0.969,0.385 10 false from IG1 NO. 1 Relay 4.094,0.458 4.406,0.656 0.313,0.198 10 false IG 3.896,2.51 4.208,2.708 0.313,0.198 10 false 5 4.083,2.635 4.396,2.833 0.313,0.198 10 false SW 2.365,1.823 2.677,2.021 0.313,0.198 10 false 4 1.969,2.531 2.281,2.729 0.313,0.198 10 false ECU 2.375,2.531 2.688,2.729 0.313,0.198 10 false 1 2.063,1.813 2.375,2.01 0.313,0.198 10 false IG 2.813,0.333 3.125,0.531 0.313,0.198 10 false 49 3.865,0.323 4.094,0.521 0.229,0.198 10 false 1 3.688,2.948 4,3.146 0.313,0.198 10 false G85 3.698,3.115 5.063,3.438 1.365,0.323 10 false Vehicle Approaching Speaker Controller

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (Operation Cancel SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Operation Cancel SW Vehicle approaching speaker switch / OFF or ON OFF: Vehicle approaching speaker switch not pressed
ON: Vehicle approaching speaker switch pressed
-

Result:
Result Proceed to
The GTS display changes according to the operation of the vehicle approaching speaker switch A
The GTS display does not change according to the operation of the vehicle approaching speaker switch B




A

2.INSPECT COMBINATION METER ASSEMBLY

B

GO TO OTHER DIAGNOSTIC PROCEDURE (The sound does not turn off or on when the vehicle approaching speaker switch is pressed)

2.INSPECT COMBINATION METER ASSEMBLY
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G85-10 (IND) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - COMBINATION METER ASSEMBLY)
a.

Disconnect the G1 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-10 (IND) - G1-14 (IND) Always Below 1 Ω
G85-10 (IND) or G1-14 (IND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR