Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2015.11
RM2170E _53 Suspension _057019 TIRE PRESSURE MONITORING _0278018 TIRE PRESSURE WARNING SYSTEM Y

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the tire pressure warning system.

·

Make sure that the wireless door lock control system has exited diagnostic mode before performing the following procedure.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Interview the customer to confirm the trouble.

HINT:

It is important to collect as much specific information as possible from the customer to allow for a quick repair.



Result:
Proceed to
NEXT



NEXT

3.ADJUST TIRE PRESSURE*
3.ADJUST TIRE PRESSURE*
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Set the tire pressure to the specified value (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).

NOTICE:

Refer to the link as the procedure for adjusting the tire pressures differs depending on the temperature of the tires.



f.

Display "ID Tire Inflation Pressure" in the Data List and check that the tire pressure values match the adjusted pressure amount.


g.

Perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).

HINT:
·

The warning threshold value changes depending on the driving conditions during initialization. As a result, the tire pressure warning light may not turn off even if the tire pressure is adjusted to the specified pressure.

·

The tire pressure warning system illuminates the tire pressure warning light to warn the driver when any of the following conditions are met:

-

Due to the operation of the tire pressure warning reset switch, the tire pressure drops to approximately 80% or less of the tire pressure set during system initialization.

-

The tire pressure drastically decreases (approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more within several minutes) to approximately 80% or less of the tire pressure* when the tires are warmed.




NOTICE:

If the tire pressure is decreased approximately 20 kPa (0.2 kgf/cm2, 2.9 psi) or more in order to adjust the tire pressure, even if the adjusted tire pressure is 80% or more than the tire pressure set during system initialization, the tire pressure warning light may illuminate if the tire pressure drops below 80% of the tire pressure set when the tires are warmed. In this case, perform initialization again.


Result:
Condition Proceed to
Tire pressure warning light remains on A
Tire pressure warning light goes off B




A

4.CHECK ECU CONNECTED TO CAN BUS*

B

END

4.CHECK ECU CONNECTED TO CAN BUS*
a.

Check the ECUs connected to the CAN bus (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
No malfunction appears A
Malfunction appears B




A

5.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)*

B

5.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)*
a.

Check for DTCs (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
CAN system DTC is not output A
CAN system DTC is output B




A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs are output A
DTCs are not output B




A

7.DTC CHART

B

8.PROBLEM SYMPTOMS TABLE
7.DTC CHART

Result:
Proceed to
NEXT



NEXT

9.CIRCUIT INSPECTION*
8.PROBLEM SYMPTOMS TABLE

Result:
Proceed to
NEXT



NEXT

9.CIRCUIT INSPECTION*
9.CIRCUIT INSPECTION*
a.

Result:
Proceed to
NEXT



NEXT

10.REPAIR OR REPLACE
10.REPAIR OR REPLACE
a.

Repair or replace parts based on the diagnosis result.


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST*
11.CONFIRMATION TEST*
a.

Check the Data List to confirm that the tire inflation pressure has been received (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST).



c.

Confirm that the initialization has been completed.


Result:
Proceed to
NEXT



NEXT

END