Home › Drivetrain › P510 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER › from 2017.06
RM2170E _52 Drivetrain _057013 P510 HYBRID TRANSMISSION / TRANSAXLE _0277995 SHIFT LEVER G

P510 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 33560C 1.INSPECT LOWER SHIFT LEVER ASSEMBLY

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the lower shift lever assembly.


a.
C249921C05
1.094,0.635 1.167,0.635 1.167,0.635 1.667,0.99 false 0.896,0.552 1.083,0.698 0.188,0.146 10 false IG 0.198,0.042 0.385,0.188 0.188,0.146 10 false *a
*a Component with harness connected
(Lower Shift Lever Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (IG) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V


HINT:

Do not disconnect the lower shift lever assembly connector.


If the result is not as specified, repair or replace the wire harness or connector.


b.
C249921C06
1.604,1.833 1.667,1.833 1.667,1.833 1.698,1.094 false 0.198,0.042 0.385,0.188 0.188,0.146 10 false *a 1.271,1.75 1.583,1.896 0.313,0.146 10 false STP
*a Component with harness connected
(Lower Shift Lever Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
8 (STP) - Body ground Ready ON, brake pedal depressed 11 to 14 V
Ready ON, brake pedal released Below 1 V


HINT:

Do not disconnect the lower shift lever assembly connector.


If the result is not as specified, repair or replace the wire harness or connector or replace the hybrid vehicle control ECU assembly.


c.
C249921C07
1.677,1.792 1.74,1.792 1.74,1.792 1.771,1.052 false 0.198,0.042 0.385,0.188 0.188,0.146 10 false *a 1.552,1.698 1.677,1.844 0.125,0.146 10 false E
*a Component with harness connected
(Lower Shift Lever Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the lower shift lever assembly connector.


If the result is not as specified, repair or replace the wire harness or connector.


d.

Inspect shift lock solenoid

i.
C249922

Disconnect the shift lock solenoid connector.


ii.
C197452C52
1.365,1.208 0.615,1.583 true 1.594,1.219 1.365,1.615 true 1.833,1.219 2.125,1.594 true 2.083,1.219 2.771,1.594 true 0.094,0.063 0.385,0.333 0.292,0.271 10 false *a 0.448,1.615 0.823,1.823 0.375,0.208 10 false SLS+ 1.198,1.625 1.594,1.833 0.396,0.208 10 false SLS- 2.063,1.625 2.292,1.833 0.229,0.208 10 false E2 2.75,1.625 2.927,1.833 0.177,0.208 10 false P
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

Standard Resistance:
Tester Connection Shift Lever Position Specified Condition
4 (P) - 3 (E2) P 10 kΩ or higher
Other than P Below 1 Ω


If the result is not as specified, replace the lower shift lever assembly.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω


If the result is not as specified, replace the lower shift lever assembly.