Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278196 LIGHTING SYSTEM D

LIGHTING (EXT)  LIGHTING SYSTEM  SYSTEM DESCRIPTION  


AUTOMATIC LIGHT CONTROL SYSTEM (w/ Automatic Light Control)


When the light control switch is in the AUTO position, the automatic light control system detects ambient light levels and controls the low beam headlights, clearance lights, taillights and license plate lights.


LIGHT AUTO TURN-OFF SYSTEM (w/ Light Auto Turn-off System (w/o Daytime Running Light))


a.

General

The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (headlights, front fog lights, taillights, clearance lights, license plate lights and rear fog light).


b.

When all of the following conditions are met, the headlights, front fog lights, taillights, clearance lights, license plate lights and rear fog light turn off:

·

The power switch is turned from on (IG) to off.

·

The headlights, front fog lights, taillights, clearance lights, license plate lights and rear fog light are on.

·

The driver door is opened.




LIGHT AUTO TURN-OFF SYSTEM (w/ Light Auto Turn-off System (w/ Daytime Running Light))


The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (headlights, taillights, clearance lights, license plate lights and daytime running lights).

The lights that will turn off will vary according to the position of the light control switch as shown in the table below.

Switch Condition Outline
Light control switch in AUTO position The exterior lights are automatically turned off when any of the following conditions are met:
·

The power switch is turned off when the exterior lights are on and the vehicle speed is less than 10 km/h (6 mph).

·

The driver door is opened after the power switch is turned off when the exterior lights are on.


Light control switch in tail or head position The low beam headlights and the high beam headlights are automatically turned off when any of the following conditions are met:
·

The power switch is turned off when the exterior lights are on and the vehicle speed is less than 10 km/h (6 mph).

·

The driver door is opened after the power switch is turned off when the exterior lights are on.


HINT:

The taillights, clearance lights, license plate lights and daytime running lights remain on.




LED HEADLIGHT SYSTEM (for LED Headlight)


a.

General

LED headlights are used to provide efficient, maintenance free lighting. Compared to halogen or HID headlights, even if an LED headlight is used for a long time, the reduction of brightness over its lifetime is less. In addition, there is no possibility of an LED having an open circuit because of vibration.


b.

Function of Main Components

Component Outline
Light Control ECU
·

Turns on the LEDs immediately when the light control switch is turned to the head position.

·

Regulates the output current flowing into the LEDs at a specified level to prevent the light from getting brighter and dimmer due to voltage variation.

·

Transmits fail signals to the main body ECU (multiplex network body ECU) when a malfunction occurs in the LED headlight system.


Combination Meter Assembly Displays a warning message to inform the driver when the light control ECU detects a malfunction in this system.
Main Body ECU (Multiplex Network Body ECU)
·

Receives fail signals from the light control ECU when a malfunction occurs in the LED headlight system, and transmits the signals to the combination meter assembly.

·

Stores Diagnostic Trouble Codes (DTCs) when the system malfunctions.





DAYTIME RUNNING LIGHT SYSTEM (w/ Daytime Running Light)


The daytime running light system is designed to automatically illuminate the daytime running lights during the day to make the vehicle more visible to other vehicles.

·

This system is controlled by the main body ECU (multiplex network body ECU).

·

The daytime running lights will turn on when all of the following conditions are met:

-

The power switch is on (READY).

-

The light control switch is in the AUTO position (the taillights are not turned on by the automatic light control system).

-

The parking brake switch is off.