DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Parking Brake SW | Parking brake switch signal | OFF or ON | OFF: Parking brake switch off
ON: Parking brake switch on |
- |
| Dimmer SW | Dimmer switch high position signal | OFF or ON | OFF: Dimmer switch in low position
ON: Dimmer switch in high or high flash position |
w/ Light Auto Turn-off System |
| Passing Light SW | Dimmer switch high flash position (pass) signal | OFF or ON | OFF: Dimmer switch not in high flash position
ON: Dimmer switch in high flash position |
w/ Light Auto Turn-off System |
| Rear Fog Light SW | Rear fog light switch signal | OFF or ON | OFF: Rear fog light switch off
ON: Rear fog light switch on |
·
w/ Light Auto Turn-off System ·
w/ Rear Fog Light |
| Front Fog Light SW | Front fog light switch signal | OFF or ON | OFF: Front fog light switch off
ON: Front fog light switch on |
·
w/ Light Auto Turn-off System ·
w/ Front Fog Light |
| Auto Light SW | Light control switch AUTO position signal | OFF or ON | OFF: Light control switch not in AUTO position
ON: Light control switch in AUTO position |
·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| Head Light SW (Head) | Light control switch head position signal | OFF or ON | OFF: Light control switch not in head position
ON: Light control switch in head position |
w/ Light Auto Turn-off System |
| Head Light SW (Tail) | Light control switch tail position signal | OFF or ON | OFF: Light control switch not in tail or head position
ON: Light control switch in tail or head position |
- |
| Illumination Rate Info | Illumination rate information | 0.00 ms. to 2162.65 ms. | Value is output according to ambient light levels | ·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| AUTO Light Status | Auto light control operation status | Not AUTO or AUTO | Not AUTO: Automatic light control not operating
AUTO: Automatic light control operating |
·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| Response Time | Delay timing of lighting the taillights when the automatic light control sensor detects brightness change | 0.1 s or 1.0 s | Customize setting displayed | ·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| Sensitivity | Sensitivity of the automatic light control system | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | ·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| Disp Ex ON Sen | Ambient brightness level required to dim display lights (combination meter, navigation display, etc.) | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | ·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| Disp Ex OFF Sen | Ambient brightness level required to cancel dimming display lights (combination meter, navigation display, etc.) | Light2, Light1, Normal, Dark1 or Dark2 | Customize setting displayed | ·
w/ Light Auto Turn-off System ·
w/ Automatic Light Control |
| The Number of DTC | Number of trouble codes | 0 to 255 | Number of stored DTCs displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Signal Switch (Right) | Turn signal switch (right) signal | OFF or ON | OFF: Turn signal switch (right) off
ON: Turn signal switch (right) on |
- |
| Turn Signal Switch (Left) | Turn signal switch (left) signal | OFF or ON | OFF: Turn signal switch (left) off
ON: Turn signal switch (left) on |
- |
| Hazard Flasher Switch | Hazard warning signal switch signal | OFF or ON | OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Daytime Running Light | Daytime running lights | OFF or ON | ·
w/ Light Auto Turn-off System ·
w/ Daytime Running Light |
| Taillight Relay | Taillight relay | OFF or ON | w/ Light Auto Turn-off System |
| Headlight Relay | Low beam headlights | OFF or ON | w/ Light Auto Turn-off System |
| Head Light Hi | High beam headlights | OFF or ON | w/ Light Auto Turn-off System |
| Front Fog Light Relay | Front fog lights | OFF or ON | ·
Light control switch is in tail position ·
w/ Light Auto Turn-off System ·
w/ Front Fog Light |
| Rear Fog Light Relay | Rear fog light | OFF or ON | ·
Light control switch is in tail position ·
w/ Light Auto Turn-off System ·
w/ Rear Fog Light |