Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Halogen Headlight) › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278188 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  DISASSEMBLY  


PROCEDURE

Hide 81510C 1.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E365278

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove them as a unit.


b.

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 81610F 2.REMOVE CLEARANCE LIGHT BULB

a.
E365280

Turn the clearance light socket with the clearance light bulb as shown in the illustration to remove them as a unit.


b.

Remove the clearance light bulb from the clearance light socket.


Hide 81144 3.REMOVE NO. 1 HEADLIGHT COVER

a.
E365282

Turn the No. 1 headlight cover as shown in the illustration to remove it.


Hide 81110B 4.REMOVE NO. 1 HEADLIGHT BULB

a.

Disconnect the connector.


b.
E365284

Turn the No. 1 headlight bulb as shown in the illustration to remove it.

NOTICE:

Do not touch the bulb glass.



Hide 85662 5.REMOVE HEADLIGHT LEVELING MOTOR

a.
E365286C02
1.604,1.167 2.229,0.698 true 1.021,1.313 1.177,1.49 0.156,0.177 10 true 1 2.24,1.75 2.396,1.948 0.156,0.198 10 false 2 2.229,0.604 2.458,0.802 0.229,0.198 10 true *a
*a Aiming Screw


Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.

HINT:
·

Turn the aiming screw until the headlight leveling motor can be moved in the direction indicated by the arrow (2) shown in the illustration.

·

Make sure to remember the number of aiming screw rotations.




b.

Turn the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to disengage the pin.

HINT:

When removing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction of the arrow (2) shown in the illustration.



c.
E372159C02
1.583,1.177 2.177,0.813 true 0.948,1.292 1.146,1.479 0.198,0.188 10 true 3 1.573,1.896 1.771,2.083 0.198,0.188 10 true 4 2.188,0.708 2.385,0.896 0.198,0.188 10 true *a
*a Aiming Screw


Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration to disengage the shaft.

HINT:

Make sure to remember the number of aiming screw rotations.



d.

Pull out the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to remove it.


Hide 85669 6.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Remove the headlight leveling motor base packing.

NOTICE:

After the headlight leveling motor base packing is removed, be sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 81138 7.REMOVE HEADLIGHT SPRING

a.
E422665C02
0.729,1.063 1.167,1.354 true 0.583,0.958 0.896,1.156 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the 4 claws to remove the 2 headlight springs.


Hide 81171B 8.REMOVE HEADLIGHT LENS

a.
E372161C02
0.99,0.063 1.302,0.219 0.313,0.156 10 false *a 0,0.813 0.313,0.969 0.313,0.156 10 false *a 0.052,1.26 0.365,1.417 0.313,0.156 10 false *a 0.219,1.844 0.531,2 0.313,0.156 10 false *a 0.594,2.01 0.844,2.167 0.25,0.156 10 false *a 2.021,2.021 2.333,2.177 0.313,0.156 10 false *a 3.115,2.021 3.323,2.177 0.208,0.156 10 false *a 3.229,1.208 3.427,1.396 0.198,0.188 10 false *b
*a Screw
*b "TORX" Screw


Remove the 7 screws.


b.

Using a T20H "TORX" driver, remove the "TORX" screw.


c.
E372162

Using a dryer, heat the backside of the headlight unit.

NOTICE:

If the headlight is heated unevenly, it will deform or melt.



d.
E422670

Disengage the 5 claws and remove the headlight lens.

NOTICE:
·

Wear rubber gloves when handling the headlight lens.

·

Do not touch the lens or the aluminum surfaces with bare hands.

·

If there are fingerprints on the aluminum surfaces, wipe them off with a soft cloth.

·

If there are fingerprints on the back of the headlight lens, replace the headlight lens.

·

Do not allow dirt or foreign matter to get on the headlight lens.



HINT:

If the lens cannot be removed even after heating, using a screwdriver with its tip wrapped in tape, lift the lens. Be careful not to damage the headlight lens and housing.



Hide 81132B 9.REMOVE HEADLIGHT LENS GASKET

a.

Remove the headlight lens gasket from the housing.