Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY(for Halogen Headlight) › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278188 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  REASSEMBLY  


PROCEDURE

Hide 81132B 1.INSTALL HEADLIGHT LENS GASKET

a.

Completely remove the old headlight lens gasket.


b.
E237693E04
1.5,0.458 1.698,0.642 0.198,0.183 10 1 0.177,0.613 0.375,0.797 0.198,0.183 10 2 1.285,1.329 1.433,1.482 0.149,0.153 10 *a 0.624,1.231 0.773,1.384 0.149,0.153 10 *b 1.371,1.064 1.371,1.311 false 0.713,0.912 0.703,1.207 false 1.473,1.87 1.733,2.033 0.260,0.163 10 *d 2.706,1.232 2.855,1.386 0.149,0.153 10 *c 2.439,1.521 2.685,1.35 false

Partially remove the release paper, and cut off a piece of it.

Text in Illustration
*a Release Paper
*b Tape
*c Headlight Lens Gasket
*d 45°


c.

Fold the release paper over the tip of a screwdriver and fix it in place with tape.

HINT:

Use the release paper that is supplied with the headlight lens gasket.



d.

Using scissors, cut the end of the headlight lens gasket at an angle (45°).


e.
E372164C02
1.156,2.958 1.469,3.115 0.313,0.156 10 false *a
*a 10 mm (0.394 in.) or more


Set the headlight lens gasket into the groove so that the ends of the gasket are aligned with the bottom of the housing, as shown in the illustration.


f.

Using the screwdriver, completely press the headlight lens gasket into the housing to install it.


g.

After pressing the headlight lens gasket completely, check that the ends overlap for 10 mm (0.394 in.) or more.

HINT:

Place the headlight lens gasket along the outside surface and press it in with the screwdriver to roll it into place. Then, set the headlight lens gasket at the center of the groove.



Hide 81171B 2.INSTALL HEADLIGHT LENS

a.
E422670

Engage the 5 claws and install the headlight lens to the housing.

NOTICE:
·

Check that all the claws are engaged.

·

Wear rubber gloves when handling the headlight lens.

·

Do not touch the lens or the aluminum surfaces with bare hands.

·

If there are fingerprints on the aluminum surfaces, wipe them off with a soft cloth.

·

If there are fingerprints on the back of the headlight lens, replace the headlight lens.

·

Do not allow dirt or foreign matter to get on the headlight lens.




b.
E372161C03
0.99,0.063 1.302,0.219 0.313,0.156 10 false *a 0,0.813 0.313,0.969 0.313,0.156 10 false *a 0.052,1.26 0.365,1.417 0.313,0.156 10 false *a 0.219,1.844 0.531,2 0.313,0.156 10 false *a 0.594,2.01 0.844,2.167 0.25,0.156 10 false *a 2.021,2.021 2.333,2.177 0.313,0.156 10 false *a 3.115,2.021 3.323,2.177 0.208,0.156 10 false *a 3.229,1.188 3.427,1.375 0.198,0.188 10 false *b
*a Screw
*b "TORX" Screw


Using a T20H "TORX" driver, install the "TORX" screw.


c.

Install the 7 screws.

NOTICE:

Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.



Hide 81138 3.INSTALL HEADLIGHT SPRING

a.
E422667

Engage the 4 claws to install the 2 headlight springs.


Hide 85669 4.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Install a new headlight leveling motor base packing.


Hide 85662 5.INSTALL HEADLIGHT LEVELING MOTOR

a.
E372160C02
1.604,1.177 2.281,0.854 true 2.292,0.771 2.521,0.938 0.229,0.167 10 true *a 1.354,1.958 1.583,2.125 0.229,0.167 10 true 1 0.969,1.271 1.146,1.448 0.177,0.177 10 true 2
*a Aiming Screw


Insert the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.


b.

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to engage the shaft.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



c.
E365287C02
1.615,1.167 2.198,0.76 true 2.208,0.656 2.438,0.833 0.229,0.177 10 true *a 2.125,1.813 2.354,1.99 0.229,0.177 10 true 3 0.979,1.323 1.177,1.5 0.198,0.177 10 true 4
*a Aiming Screw


Turn the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration and engage the pin to install the headlight leveling motor to the headlight unit.

HINT:

When installing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction of the arrow (3) shown in the illustration.



d.

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to install it.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



Hide 81110B 6.INSTALL NO. 1 HEADLIGHT BULB

a.
E365285

Turn the No. 1 headlight bulb as shown in the illustration to install it.

NOTICE:

Do not touch the bulb glass.



b.

Connect the connector.


Hide 81144 7.INSTALL NO. 1 HEADLIGHT COVER

a.
E365283

Turn the No. 1 headlight cover as shown in the illustration to install it.


Hide 81610F 8.INSTALL CLEARANCE LIGHT BULB

a.

Install the clearance light bulb to the clearance light socket.


b.
E365281

Turn the clearance light socket with the clearance light bulb as shown in the illustration to install them as a unit.


Hide 81510C 9.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the front turn signal light socket.


b.
E365279

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install them as a unit.