Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for LED Headlight) › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278187 HEADLIGHT ASSEMBLY(for LED Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for LED Headlight)  REASSEMBLY  


PROCEDURE

Hide 81160A 1.INSTALL HEADLIGHT LED UNIT ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight LED unit or other components.

·

If there are any fingerprints or foreign matter on the headlight unit or other components, wipe them off with a soft cloth.



a.
E372207

Engage the guide while turning the aiming screw in the direction indicated by the arrow shown in the illustration to install the headlight LED unit assembly to the housing.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



b.
E372205

Connect the connector.


Hide 81132B 2.INSTALL HEADLIGHT LENS GASKET

a.

Completely remove the old headlight lens gasket.


b.
E237693E05
1.5,0.47 1.698,0.654 0.198,0.183 10 1 0.177,0.625 0.375,0.809 0.198,0.183 10 2 1.285,1.341 1.433,1.494 0.149,0.153 10 *a 0.624,1.243 0.773,1.396 0.149,0.153 10 *b 1.371,1.076 1.371,1.323 false 0.713,0.924 0.703,1.219 false 1.512,1.883 1.661,2.036 0.149,0.153 10 *d 2.706,1.245 2.855,1.398 0.149,0.153 10 *c 2.439,1.533 2.685,1.362 false

Partially remove the release paper, and cut off a piece of it.

Text in Illustration
*a Release Paper
*b Tape
*c Headlight Lens Gasket
*d 45°


c.

Fold the release paper over the tip of a screwdriver and fix it in place with tape.

HINT:

Use the release paper that is supplied with the headlight lens gasket.



d.

Using scissors, cut the end of the headlight lens gasket at an angle (45°).


e.
E372181C02
1.167,2.948 1.479,3.146 0.313,0.198 10 false *a
*a 10 mm (0.394 in.) or more


Set the headlight lens gasket into the groove so that the ends of the gasket are aligned with the bottom of the housing, as shown in the illustration.


f.

Using the screwdriver, completely press the headlight lens gasket into the housing to install it.


g.

After pressing the headlight lens gasket completely, check that the ends overlap for 10 mm (0.394 in.) or more.

HINT:

Place the headlight lens gasket along the outside surface and press it in with the screwdriver to roll it into place. Then, set the headlight lens gasket at the center of the groove.



Hide 81171B 3.INSTALL HEADLIGHT LENS

a.
E422664

Engage the 5 claws to install the headlight lens to the housing.

NOTICE:
·

Check that all the claws are engaged.

·

Wear rubber gloves when handling the headlight lens.

·

Do not touch the lens or the aluminum surfaces with bare hands.

·

If there are fingerprints on the aluminum surfaces, wipe them off with a soft cloth.

·

If there are fingerprints on the back of the headlight lens, replace the headlight lens.

·

Do not allow dirt or foreign matter to get on the headlight lens.




b.
E372176C03
0.906,0.031 1.219,0.188 0.313,0.156 10 false *a 3.198,1.104 3.406,1.271 0.208,0.167 10 false *b 0.042,0.854 0.354,1.01 0.313,0.156 10 false *a 0.115,1.365 0.427,1.521 0.313,0.156 10 false *a 0.146,1.833 0.458,1.99 0.313,0.156 10 false *a 0.531,2.021 0.844,2.177 0.313,0.156 10 false *a 1.938,2.021 2.25,2.177 0.313,0.156 10 false *a 2.542,2.021 2.854,2.177 0.313,0.156 10 false *a
*a Screw
*b "TORX" Screw


Using a T20H "TORX" driver, install the "TORX" screw.


c.

Install the 7 screws.

NOTICE:

Make sure the headlight lens gasket is not protruding and completely contacts the headlight lens.



d.
E412545

Connect the connector.


Hide 81138 4.INSTALL HEADLIGHT SPRING

a.
E422668

Engage the 4 claws to install the 2 headlight springs.


Hide 81144 5.INSTALL NO. 1 HEADLIGHT COVER

a.
E372175

Turn the No. 1 headlight cover as shown in the illustration to install it.


Hide 85669 6.INSTALL HEADLIGHT LEVELING MOTOR BASE PACKING

a.

Install a new headlight leveling motor base packing.


Hide 85662 7.INSTALL HEADLIGHT LEVELING MOTOR

a.
E372173C02
1.604,1.073 2.135,0.583 true 2.135,0.479 2.365,0.667 0.229,0.188 10 true *a 1.302,1.896 1.531,2.083 0.229,0.188 10 true 1 1,1.188 1.177,1.365 0.177,0.177 10 true 2
*a Aiming Screw


Insert the headlight leveling motor in the direction indicated by the arrow (1) shown in the illustration.


b.

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (2) shown in the illustration to engage the shaft.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



c.
E372171C02
1.615,1.083 2.354,0.594 true 2.365,0.5 2.583,0.667 0.219,0.167 10 true *a 2.156,1.698 2.375,1.865 0.219,0.167 10 true 3 0.917,1.219 1.094,1.396 0.177,0.177 10 true 4
*a Aiming Screw


Turn the headlight leveling motor in the direction indicated by the arrow (3) shown in the illustration and engage the pin to install the headlight leveling motor to the headlight unit.

HINT:

When installing the headlight leveling motor of the headlight assembly RH, turn the headlight leveling motor in the opposite direction of the arrow (3) shown in the illustration.



d.

Turn the aiming screw of the headlight leveling motor in the direction indicated by the arrow (4) shown in the illustration to install it.

HINT:

Turn the aiming screw the same number of times as it was turned during removal.



Hide 81510C 8.INSTALL FRONT TURN SIGNAL LIGHT BULB

a.

Install the front turn signal light bulb to the front turn signal light socket.


b.
E372179

Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to install them as a unit.