87940
1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly LH connector.
Apply auxiliary battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Auxiliary battery positive (+) → Terminal 6 (MV)
Auxiliary battery negative (-) → Terminal 5 (M+) |
Turns upward |
| Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 6 (MV) |
Turns downward |
| Auxiliary battery positive (+) → Terminal 4 (MH)
Auxiliary battery negative (-) → Terminal 5 (M+) |
Turns left |
| Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 4 (MH) |
Turns right |
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
If the result is not as specified, replace the outer rear view mirror assembly LH.
Check the operation of the mirror heater. (w/ Mirror Heater)
Disconnect the outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (+) - 9 (-) | 25°C (77°F) | 8.5 to 11.5 Ω |
| *a | Component without harness connected
(Outer Rear View Mirror Assembly LH) |
If the result is not as specified, replace the outer rear view mirror assembly LH.
Connect a positive (+) lead from the auxiliary battery to terminal 3 and a negative (-) lead to terminal 9 and check that the mirror surface becomes warm.
It takes a short time for the mirror to become warm.
Mirror becomes warm.
If the result is not as specified, replace the outer rear view mirror assembly LH.
87940
2.INSPECT OUTER MIRROR RETRACTOR LH
Check the operation of the retractable mirror. (w/ Power Retractable Mirror)
Disconnect and reconnect the auxiliary battery between each mirror position check.
The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.
Disconnect the outer rear view mirror assembly LH connector.
For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Forward position (A) | Moves from (A) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Forward position (A) | Does not move |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Position between forward position (A) and driving position (C) | Moves from (B) to forward position (A) |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Driving position (C) | Moves from (C) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Driving position (C) | Does not move |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Position between driving position (C) and retracted position (E) | Moves from (D) to driving position (C) |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Retracted position (E) | Does not move |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Retracted position (E) | Moves from (E) to driving position (C) |
| *1 | (A) Forward Position |
| *2 | (B) |
| *3 | (C) Driving position |
| *4 | (D) |
| *5 | (E) Retracted Position |
| *a | Component without harness connected
(Outer Mirror Retractor LH) |
If the result is not as specified, replace the outer mirror retractor LH.
87910
3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly RH connector.
Apply auxiliary battery voltage and check the operation of the mirror.
| Measurement Condition | Specified Condition |
|---|---|
| Auxiliary battery positive (+) → Terminal 6 (MV)
Auxiliary battery negative (-) → Terminal 5 (M+) |
Turns upward |
| Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 6 (MV) |
Turns downward |
| Auxiliary battery positive (+) → Terminal 4 (MH)
Auxiliary battery negative (-) → Terminal 5 (M+) |
Turns left |
| Auxiliary battery positive (+) → Terminal 5 (M+)
Auxiliary battery negative (-) → Terminal 4 (MH) |
Turns right |
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
If the result is not as specified, replace the outer rear view mirror assembly RH.
Check the operation of the mirror heater. (w/ Mirror Heater)
Disconnect the outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (+) - 9 (-) | 25°C (77°F) | 8.5 to 11.5 Ω |
| *a | Component without harness connected
(Outer Rear View Mirror Assembly RH) |
If the result is not as specified, replace the outer rear view mirror assembly RH.
Connect a positive (+) lead from the auxiliary battery to terminal 3 and a negative (-) lead to terminal 9 and check that the mirror surface becomes warm.
It takes a short time for the mirror to become warm.
Mirror becomes warm.
If the result is not as specified, replace the outer rear view mirror assembly RH.
87910
4.INSPECT OUTER MIRROR RETRACTOR RH
Check the operation of the retractable mirror. (w/ Power Retractable Mirror)
Disconnect and reconnect the auxiliary battery between each mirror position check.
The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.
Disconnect the outer rear view mirror assembly RH connector.
For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Forward position (A) | Moves from (A) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Forward position (A) | Does not move |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Position between forward position (A) and driving position (C) | Moves from (B) to forward position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Position between forward position (A) and driving position (C) | Moves from (B) to retracted position (A) |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Driving position (C) | Moves from (C) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Driving position (C) | Does not move |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Position between driving position (C) and retracted position (E) | Moves from (D) to retracted position (E) |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Position between driving position (C) and retracted position (E) | Moves from (D) to driving position (C) |
| Auxiliary battery positive (+) → Terminal 11 (MR)
Auxiliary battery negative (-) → Terminal 10 (MF) |
Retracted position (E) | Does not move |
| Auxiliary battery positive (+) → Terminal 10 (MF)
Auxiliary battery negative (-) → Terminal 11 (MR) |
Retracted position (E) | Moves from (E) to driving position (C) |
| *1 | (A) Forward Position |
| *2 | (B) |
| *3 | (C) Driving position |
| *4 | (D) |
| *5 | (E) Retracted Position |
| *a | Component without harness connected
(Outer Mirror Retractor RH) |
If the result is not as specified, replace the outer mirror retractor RH.