Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM D

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  OPERATION CHECK  


CHECK WINDOW LOCK SWITCH


B479724

HINT:

Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).


a.

Check that the front passenger and rear windows cannot be operated when the window lock switch of the power window regulator master switch assembly is pushed in.

OK:

Front passenger and rear windows are disabled.



b.

Check that the front passenger and rear windows can be operated when the window lock switch of the power window regulator master switch assembly is pushed in again.

OK:

Front passenger and rear windows operate normally.




CHECK MANUAL UP / DOWN FUNCTION


a.

Check that the driver door power window operates as follows:

OK
Condition Master Switch Switch Operation Power Window
Power switch on (IG) Driver door Pulled halfway up UP (Closes)
Pushed halfway down DOWN (Opens)


b.

Check that the front passenger door window and rear power windows operate as follows:

OK
Condition Regulator Switch Switch Operation Power Window
·

Power switch on (IG)

·

Window lock switch off


Front passenger door Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear LH door Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear RH door Pulled up UP (Closes)
Pushed down DOWN (Opens)



CHECK AUTO UP / DOWN FUNCTION


a.

Check that the driver door power window operates as follows:

OK
Condition Master Switch Switch Operation Power Window
Power switch on (IG) Driver door Pulled up (One touch operation) AUTO UP (Closes)
Pushed down (One touch operation) AUTO DOWN (Opens)



CHECK REMOTE MANUAL UP / DOWN FUNCTION


a.

Check that the front passenger door window and rear power windows operate as follows:

OK
Condition Master Switch Switch Operation Power Window
·

Power switch on (IG)

·

Window lock switch off


Front passenger door Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear LH door Pulled up UP (Closes)
Pushed down DOWN (Opens)
Rear RH door Pulled up UP (Closes)
Pushed down DOWN (Opens)



CHECK POWER WINDOW OPERATION FUNCTION AFTER POWER SWITCH IS TURNED OFF


a.

Check that all the power windows can be operated with the power window regulator master switch assembly and power window regulator switch assemblies (for front passenger door, rear LH and RH doors) after the power switch is turned off.

HINT:

If the window lock switch is on, the power windows cannot be operated besides the driver door power window. Therefore, turn the window lock switch off before checking the window operation.



b.

Check that the key-off operation function does not operate after the driver door or front passenger door is opened.

HINT:

If the driver door or front passenger door is opened during automatic window operation while the key-off operation function is on, the window will continue operating.



c.

Check that all the power windows cannot be operated after more than approximately 45 seconds have elapsed since the power switch was turned off.



CHECK JAM PROTECTION FUNCTION


a.

Check the basic function.

CAUTION:

Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.


HINT:

The jam protection function operates during both the auto up and manual up operations while the hybrid control system is started or the power switch is on (IG), and also 45 seconds have elapsed after the power switch was turned off.


i.

Fully open the driver door window.


ii.
B274528C19
1.648,0.209 1.882,0.209 1.882,0.209 1.882,0.782 false 2.249,0.209 2.14,0.209 2.14,0.209 2.14,0.713 false 1.447,0.112 1.626,0.268 0.179,0.156 10 *a 2.277,0.112 2.452,0.272 0.174,0.161 10 *b
*a Check Jig
*b Cloth


Set a check jig wrapped with a piece of cloth near the window fully closed position.


iii.

Operate the auto up or manual up function and check that the power window stops and goes down after the check jig is caught between the door glass and door frame, and stops.

HINT:
·

If a manual up operation is performed from the seat, the door glass will lower approximately 30 mm (1.181 in.) from the point it contacts the end of the hammer or continue lowering for approximately 5 seconds and then stop.

·

If a manual up operation is not performed from the seat, the door glass will lower approximately 125 mm (4.921 in.) from the point it contacts the end of the hammer or continue lowering for approximately 5 seconds and then stop.

·

After the jam protection function operates when an auto up or manual up operation is performed, the jam protection function will not operate when the manual up operation is performed again within approximately 4 seconds.

·

After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.




iv.

While the power window is moving down, check that the door glass cannot be raised when the power window switch is used.




CHECK CATCH PROTECTION FUNCTION


a.

Check the basic function.

CAUTION:

Do not put your fingers between the door frame and door glass to check the catch protection function. Also, prevent any part of your body from being caught during inspection.


HINT:

The catch protection function is operative during both the auto down and manual down operations while the power switch is on (IG) or on (READY), and also for approximately 45 seconds after the power switch is turned off.


i.
B479727

Fully close the driver door window.


ii.

Operate the auto down or manual down function to open the power window, grasp the upper edge of the door glass with one or two hands and check that the power window stops.

HINT:

After the catch protection function has operated when an auto down or manual down operation was performed, the catch protection function will not operate if the manual down operation is performed again within approximately 4 seconds.





CHECK POWER WINDOW REGULATOR MASTER SWITCH LED ILLUMINATION


a.

Check the LED illumination (power window regulator master switch assembly).

i.

Check that the LEDs located on the power window regulator master switch assembly illuminate when the power switch is turned to on (IG).