READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch to on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / D-Door Motor or Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Door P/W Auto SW | Driver door power window auto switch signal | OFF or ON | OFF: Driver door power window auto switch not operated
ON: Driver door power window auto switch operated |
- |
| D Door P/W Up SW | Driver door power window manual up switch signal | OFF or ON | OFF: Driver door power window manual up switch not operated
ON: Driver door power window manual up switch operated |
- |
| D Door P/W Down SW | Driver door power window manual down switch signal | OFF or ON | OFF: Driver door power window manual down switch not operated
ON: Driver door power window manual down switch operated |
- |
| Glass Position (Close - 1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (1/4 - 2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (2/4 - 3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| Glass Position (3/4 - Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position | OK or Caution | OK: Normal manual up operation
Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
| D Window Auto Up | Auto up operation using the power window regulator master switch assembly | OFF or ON | Customize setting displayed | - |
| D Window Auto Down | Auto down operation using the power window regulator master switch assembly | OFF or ON | Customize setting displayed | - |
| Number of Trouble Codes | Number of trouble codes / Min.: 0 or Max.: 255 | Min.: 0 or Max.: 255 | Number of DTCs will be displayed | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IG SW | Power switch status | OFF or ON | OFF: Power switch off or ON (ACC)
ON: Power switch on (IG) |
"OFF" is also displayed for this item when the power switch is on (IG). |
| FR Door Courtesy SW | Front door courtesy light switch | OFF or ON | OFF: Front door RH closed
ON: Front door RH open |
- |
| FL Door Courtesy SW | Front door courtesy light switch | OFF or ON | OFF: Front door LH closed
ON: Front door LH open |
- |
| Communication D-Door Motor | Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP | STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch to on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / D-Door Motor or Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF / UP / DOWN | - |