Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door) › from 2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278151 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


PROCEDURE

Hide 85720D 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Jam Protection Function)

a.
E292072C34
1.198,1.479 1.906,1.479 false 1.917,3.417 2.417,3.417 false 1.958,3.781 2.458,3.781 false 0.969,3.802 1.469,3.802 false 1.01,3.427 1.51,3.427 false 2.896,1.333 3.208,1.531 0.313,0.198 10 false *c 0.302,2.604 0.615,2.802 0.313,0.198 10 false *a 1,1.396 1.354,1.76 0.354,0.365 10 false *d 2.323,2.24 2.635,2.438 0.313,0.198 10 false *b 2.458,3.333 2.917,3.531 0.458,0.198 10 false GND 2.51,3.698 3.125,3.896 0.615,0.198 10 false DOWN 0.854,3.344 1.01,3.542 0.156,0.198 10 false B 0.729,3.719 1.042,3.917 0.313,0.198 10 false UP
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).


Motor gear rotates clockwise
1.

Connect the positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85720D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/o Jam Protection Function)

a.
B127535C23
0.063,0 0.229,0.177 0.167,0.177 10 false *a 1.573,0.885 1.75,1.094 0.177,0.208 10 false *c 1.25,1.646 1.51,1.844 0.26,0.198 10 false *b 0.74,0.26 0.979,0.469 0.24,0.208 10 false *d
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Apply auxiliary battery voltage to the motor connector according to the table below.

NOTICE:

Do not apply auxiliary battery voltage to any terminals except terminals 1 and 2.


Standard:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Motor gear rotates clockwise
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.


Hide 85710E 3.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Jam Protection Function)

a.
E292071C31
1.563,1.479 2.604,1.479 true 1.188,3.427 1.51,3.427 false 1.906,3.438 2.229,3.438 false 1.125,3.802 1.448,3.802 false 1.969,3.802 2.292,3.802 false 2.646,1.417 2.958,1.615 0.313,0.198 10 false *d 0.26,2.583 0.573,2.781 0.313,0.198 10 false *a 0.531,1.302 0.99,1.5 0.458,0.198 10 false *b 1.115,2.219 1.531,2.531 0.417,0.313 10 false *c 1.031,3.365 1.344,3.563 0.313,0.198 10 false B 0.885,3.75 1.198,3.948 0.313,0.198 10 false UP 2.313,3.385 2.76,3.656 0.448,0.271 10 false GND 2.354,3.74 2.938,3.969 0.583,0.229 10 false DOWN
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Apply positive (+) auxiliary battery voltage to connector terminal 2 (B).

NOTICE:

Do not apply positive (+) auxiliary battery voltage to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a ground lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.


NOTICE:

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.



Hide 85710E 4.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/o Jam Protection Function)

a.
B127536C25
2.595,0.313 2.769,0.479 0.175,0.166 10 *b 2.068,1.551 2.261,1.716 0.193,0.166 10 *d 1.575,0.892 1.731,1.057 0.156,0.166 10 *c 1.033,0.032 1.224,0.198 0.191,0.166 10 *a
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Counterclockwise
*c Clockwise
*d Motor Gear


Apply auxiliary battery voltage to the motor connector according to the table below.

NOTICE:

Do not apply auxiliary battery voltage to any terminals except terminals 1 and 2.


Standard:
Measurement Condition Specified Condition
Auxiliary battery positive (+) → Terminal 1
Auxiliary battery negative (-) → Terminal 2
Motor gear rotates clockwise
Auxiliary battery positive (+) → Terminal 2
Auxiliary battery negative (-) → Terminal 1
Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly RH.