Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH › from 2017.06
RM2170E _59 Vehicle Exterior _057047 MIRROR (EXT) _0278171 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Power Retractable Mirror)

a.
B254350E05
1.698,3.688 1.469,4.156 false 1.604,3.688 1.125,4.156 false 1.5,3.688 0.76,4.156 false 1.385,3.698 0.427,4.156 false 1.813,3.698 1.885,4.156 false 1.917,3.688 2.323,4.156 false 2.031,3.688 2.76,4.156 false 1.719,0.854 1.719,0.406 1.719,0.406 1.531,0.406 false 1.708,1.865 1.708,2.26 1.708,2.26 1.938,2.26 false 0.396,2.781 0.844,3.115 0.448,0.333 10 false *c 2.76,4.198 3.302,4.542 0.542,0.344 10 false HR 2.26,4.188 2.698,4.49 0.438,0.302 10 false VR 1.813,4.188 2.229,4.51 0.417,0.323 10 false VL 1.354,4.177 1.823,4.5 0.469,0.323 10 false HL 0.958,4.167 1.302,4.469 0.344,0.302 10 false M+ 0.656,4.167 0.958,4.479 0.302,0.313 10 false E 0.323,4.167 0.625,4.448 0.302,0.281 10 false B 1.323,0.323 1.781,0.667 0.458,0.344 10 false *a 1.99,2.177 2.406,2.521 0.417,0.344 10 false *b

Check the mirror select switch and mirror surface adjust switch.

Text in Illustration
*a Mirror Select Switch
*b Mirror Surface Adjust Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)

i.

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Power Retractable Mirror)

a.

Check the mirror select switch and mirror surface adjust switch.

Text in Illustration
*a Mirror Select Switch
*b Mirror Surface Adjust Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)

i.
B254629E21
1.708,3.698 1.927,4.146 false 1.594,3.688 1.552,4.156 false 1.479,3.688 1.281,4.156 false 1.385,3.698 1.042,4.156 false 1.281,3.698 0.698,4.156 false 1.167,3.698 0.365,4.156 false 1.813,3.698 2.354,4.156 false 1.927,3.688 2.719,4.156 false 2.042,3.688 3.167,4.156 false 1.552,0.865 1.552,0.344 1.552,0.344 1.375,0.344 false 1.719,1.875 1.719,2.375 1.719,2.375 1.979,2.375 false 0.417,2.708 0.635,2.917 0.219,0.208 10 false *c 3.125,4.167 3.396,4.375 0.271,0.208 10 false HR 2.646,4.167 2.896,4.417 0.25,0.25 10 false VR 2.281,4.167 2.521,4.427 0.24,0.26 10 false VL 1.854,4.167 2.104,4.396 0.25,0.229 10 false HL 1.438,4.167 1.719,4.396 0.281,0.229 10 false M+ 0.573,4.167 0.854,4.396 0.281,0.229 10 false MR 0.24,4.167 0.49,4.396 0.25,0.229 10 false MF 1.219,4.167 1.375,4.406 0.156,0.24 10 false E 0.979,4.167 1.125,4.375 0.146,0.208 10 false B 1.177,0.25 1.385,0.469 0.208,0.219 10 false *a 2.031,2.302 2.24,2.521 0.208,0.219 10 false *b

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (VL) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
4 (VL) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
5 (HL) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (VR) - 8 (B)
6 (M+) - 7 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
3 (VR) - 7 (E)
6 (M+) - 8 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 8 (B)
6 (M+) - 7 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
2 (HR) - 7 (E)
6 (M+) - 8 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror retract switch.

Text in Illustration
*a Mirror Retract Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)

i.
B254629E23
1.479,3.688 1.573,4.156 false 1.385,3.698 1.26,4.156 false 1.281,3.698 1,4.156 false 1.167,3.698 0.552,4.156 false 2.031,0.854 2.031,0.385 2.031,0.385 2.208,0.385 false 0.469,2.729 0.74,2.917 0.271,0.188 10 false *b 0.813,4.156 1.104,4.344 0.292,0.188 10 false MR 0.406,4.156 0.729,4.344 0.323,0.188 10 false MF 1.531,4.156 1.813,4.333 0.281,0.177 10 false E 1.188,4.156 1.417,4.313 0.229,0.156 10 false B 2.25,0.302 2.469,0.5 0.219,0.198 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (MF) - 7 (E) Mirror retract switch pushed Below 1 Ω
9 (MR) - 8 (B) Below 1 Ω
10 (MF) - 8 (B) Mirror retract switch released Below 1 Ω
9 (MR) - 7 (E) Below 1 Ω


If the result is not as specified, replace the outer mirror switch assembly.



Hide 3.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Mirror Heater)

a.

Check the mirror select switch and mirror surface adjust switch.

Text in Illustration
*a Mirror Select Switch
*b Mirror Surface Adjust Switch
*c Component without harness connected
(Outer Mirror Switch Assembly)

i.
B322111E04
1.302,4.135 1.479,3.604 false 1.938,4.125 1.979,3.583 false 2.24,4.135 2.125,3.594 false 1.594,4.125 1.656,3.604 false 2.563,4.135 2.281,3.594 false 2.885,4.125 2.427,3.604 false 0.979,4.115 1.156,3.604 false 2.115,2.365 1.698,2.365 1.698,2.365 1.698,1.781 false 1.708,0.802 1.708,0.302 1.708,0.302 1.292,0.302 false 1.104,0.198 1.417,0.354 0.313,0.156 10 false *a 2.156,2.26 2.469,2.417 0.313,0.156 10 false *b 0.188,2.521 0.385,2.677 0.198,0.156 10 false *c 0.927,4.167 1.083,4.365 0.156,0.198 10 false B 1.25,4.167 1.406,4.365 0.156,0.198 10 false E 1.521,4.167 1.833,4.365 0.313,0.198 10 false M+ 1.854,4.167 2.167,4.365 0.313,0.198 10 false HL 2.188,4.167 2.5,4.365 0.313,0.198 10 false VL 2.5,4.167 2.813,4.365 0.313,0.198 10 false VR 2.854,4.167 3.167,4.365 0.313,0.198 10 false HR

Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Switch Condition Specified Condition
16 (VL) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
16 (VL) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
17 (HL) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
15 (VR) - 22 (B)
19 (M+) - 20 (E)
UP Below 1 Ω
OFF 10 kΩ or higher
15 (VR) - 20 (E)
19 (M+) - 22 (B)
DOWN Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 22 (B)
19 (M+) - 20 (E)
LEFT Below 1 Ω
OFF 10 kΩ or higher
14 (HR) - 20 (E)
19 (M+) - 22 (B)
RIGHT Below 1 Ω
OFF 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.