Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  B1643/81  Side Satellite Sensor Bus RH Initialization Incomplete  B1692/81  Lost Communication with Door Side Airbag Sensor RH  B1693/81  Door Side Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

w/o Occupant Classification System:

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

The side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1643/81
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Airbag sensor assembly




w/ Occupant Classification System:

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH.

The side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1643/81
B1692/81
B1693/81
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Side No. 2 airbag sensor assembly RH malfunction

·

Door side airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Side airbag sensor assembly RH

·

Side No. 2 airbag sensor assembly RH

·

Door side airbag sensor RH

·

Airbag sensor assembly




WIRING DIAGRAM

w/o Occupant Classification System:
C239250E90
0.552,4.698 0.854,4.844 0.302,0.146 10 false M25 0.552,4.875 1.781,5.208 1.229,0.333 10 false Side Airbag Sensor Assembly RH 3.042,4.875 4.51,5.219 1.469,0.344 10 false Side No. 2 Airbag Sensor Assembly RH 3.042,4.698 3.344,4.844 0.302,0.146 10 false M27 5.24,4.844 6.833,5.042 1.594,0.198 10 false Airbag Sensor Assembly 5.24,4.667 5.604,4.833 0.365,0.167 10 false M37 1.125,0.896 1.521,1.052 0.396,0.156 10 false BBR+ 1.583,0.792 1.688,0.948 0.104,0.156 10 false 4 1.156,1.792 1.521,1.948 0.365,0.156 10 false BBR- 5.563,0.896 5.958,1.052 0.396,0.156 10 false BBR+ 5.365,0.792 5.542,0.948 0.177,0.156 10 false 8 5.323,1.698 5.5,1.854 0.177,0.156 10 false 11 5.563,1.792 5.958,1.948 0.396,0.156 10 false BBR- 1.583,1.698 1.688,1.854 0.104,0.156 10 false 3 1.125,3.042 1.521,3.198 0.396,0.156 10 false BCR+ 1.583,2.948 1.688,3.104 0.104,0.156 10 false 1 2.927,3.833 3.031,3.99 0.104,0.156 10 false 1 1.146,3.938 1.521,4.094 0.375,0.156 10 false BCR- 3.073,3.042 3.469,3.198 0.396,0.156 10 false BCR+ 3.073,3.938 3.469,4.094 0.396,0.156 10 false BCR- 1.583,3.833 1.688,3.99 0.104,0.156 10 false 2 2.927,2.948 3.031,3.104 0.104,0.156 10 false 2

w/ Occupant Classification System:
B483593E03
5.313,0.427 6.073,0.74 0.76,0.313 10 false 17 5.313,1 6.073,1.313 0.76,0.313 10 false 18 5.5,4.698 6.26,5.01 0.76,0.313 10 false M58 5.5,4.844 7.083,5.177 1.583,0.333 10 false Airbag Sensor Assembly 5.552,0.542 6.313,0.854 0.76,0.313 10 false BBR+ 5.552,1.115 6.313,1.427 0.76,0.313 10 false BBR- 1.135,0.542 1.896,0.854 0.76,0.313 10 false BBR+ 1.135,1.115 1.896,1.427 0.76,0.313 10 false BBR- 1.135,1.698 1.896,2.01 0.76,0.313 10 false BCR+ 1.135,2.302 1.896,2.615 0.76,0.313 10 false BCR- 1.583,0.448 2.344,0.76 0.76,0.313 10 false 4 1.583,1.021 2.344,1.333 0.76,0.313 10 false 3 1.583,1.604 2.344,1.917 0.76,0.313 10 false 1 1.583,2.208 2.344,2.521 0.76,0.313 10 false 2 3.469,1.698 4.229,2.01 0.76,0.313 10 false BCR+ 3.469,2.302 4.229,2.615 0.76,0.313 10 false BCR- 3.292,1.615 4.052,1.927 0.76,0.313 10 false 4 3.292,2.208 4.052,2.521 0.76,0.313 10 false 3 0.552,2.625 1.313,2.938 0.76,0.313 10 false M25 0.552,2.792 2.688,3.146 2.135,0.354 10 false Side Airbag Sensor Assembly RH 3.292,3.688 4.052,4 0.76,0.313 10 false 1 3.292,4.229 4.052,4.542 0.76,0.313 10 false 2 3.469,3.813 4.229,4.125 0.76,0.313 10 false BDR+ 3.469,4.344 4.229,4.656 0.76,0.313 10 false BDR- 3.417,4.677 4.177,4.99 0.76,0.313 10 false M54 3.417,4.844 5.031,5.333 1.615,0.49 10 false Side No. 2 Airbag Sensor Assembly RH 2.344,3.792 3.104,4.104 0.76,0.313 10 false HM3 2.344,4.333 3.104,4.646 0.76,0.313 10 false HM3 2.458,3.604 3.219,3.917 0.76,0.313 10 false 1 2.458,4.135 3.219,4.448 0.76,0.313 10 false 2 1.125,3.802 1.885,4.115 0.76,0.313 10 false BDR+ 1.156,4.344 1.917,4.656 0.76,0.313 10 false BDR- 1.583,3.698 2.344,4.01 0.76,0.313 10 false 2 1.583,4.229 2.344,4.542 0.76,0.313 10 false 1 0.542,4.677 1.302,4.99 0.76,0.313 10 false H12 0.542,4.844 2.427,5.24 1.885,0.396 10 false Door Side Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o Occupant Classification System A
w/ Occupant Classification System B




A

2.CHECK CURRENT DTC

B

18.CHECK CURRENT DTC
2.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1642, B1643 or 81 is output. A
Current DTC B1623 is output. B
Current DTC B1632 or B1633 is output. C
Current DTC B1622 is output. D
Current DTCs B1622, B1623, B1632, B1633, B1642, B1643 and 81 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then to on (IG) again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643 and 81 may be output at this time, but they are not related to this check.





A

3.CHECK CONNECTORS

B

8.CHECK HISTORY DTC

C

13.CHECK CONNECTORS

D

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

E

3.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

4.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)
a.
C238219C20
1.146,0.521 1.521,0.771 0.375,0.25 0.552,3.615 0.917,3.865 0.365,0.25 1.76,3.76 2.135,4.198 false 1.656,3.771 1.281,4.208 false 1.604,2.479 1.604,1.99 1.604,1.99 1.448,1.99 false 1.865,0.844 1.5,1.115 false 2.063,0.625 2.417,1.115 false 2,1.083 2,1.26 false 1.021,2.479 1.594,2.854 0.573,0.375 10 false D 1.323,2.479 1.615,2.875 0.292,0.396 10 false C 1.781,2.479 2.135,2.844 0.354,0.365 10 false B 2.094,2.479 2.375,2.802 0.281,0.323 10 false A 0.708,2.479 1.083,2.854 0.375,0.375 10 false *1 2.51,2.198 2.813,2.573 0.302,0.375 10 false *2 0.802,0.229 1.094,0.542 0.292,0.313 10 false *a 0.385,3.208 0.813,3.521 0.427,0.313 10 false *b 1.323,1.135 1.823,1.469 0.5,0.333 10 false BBR- 2.292,1.135 2.844,1.406 0.552,0.271 10 false BBR+ 1.208,0.563 1.646,0.896 0.438,0.333 10 false M37 0.615,3.656 1.104,3.958 0.49,0.302 10 false M25 2.021,4.219 2.708,4.49 0.688,0.271 10 false BBR+ 1.115,4.229 1.656,4.521 0.542,0.292 10 false BBR- 1.292,1.917 1.646,2.25 0.354,0.333 10 false *3 1.938,1.292 2.198,1.615 0.26,0.323 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
M25-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always 1 MΩ or higher
M25-4 (BBR+) - Body ground Always 1 MΩ or higher
M25-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

5.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)
a.
C256981C36
0.948,0.563 1.313,0.802 0.365,0.24 0.604,3.615 0.958,3.823 0.354,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.26,1.063 1.927,0.667 false 1.344,4.073 1.667,3.698 false 2.146,4.063 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 1,0.604 1.49,0.896 0.49,0.292 10 false M25 0.656,3.635 1.146,3.927 0.49,0.292 10 false M27 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

7.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

C

7.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. A
DTC B1642, B1643 or 81 is output. B
DTC B1647, B1648 or 82 is output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

8.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1622 is not output. A
History DTC B1622 is output. B


HINT:

Codes other than history DTC B1622 may be output at this time, but they are not related to this check.




A

9.CHECK CONNECTORS

B

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
9.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

10.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)
a.
C238219C20
1.146,0.521 1.521,0.771 0.375,0.25 0.552,3.615 0.917,3.865 0.365,0.25 1.76,3.76 2.135,4.198 false 1.656,3.771 1.281,4.208 false 1.604,2.479 1.604,1.99 1.604,1.99 1.448,1.99 false 1.865,0.844 1.5,1.115 false 2.063,0.625 2.417,1.115 false 2,1.083 2,1.26 false 1.021,2.479 1.594,2.854 0.573,0.375 10 false D 1.323,2.479 1.615,2.875 0.292,0.396 10 false C 1.781,2.479 2.135,2.844 0.354,0.365 10 false B 2.094,2.479 2.375,2.802 0.281,0.323 10 false A 0.708,2.479 1.083,2.854 0.375,0.375 10 false *1 2.51,2.198 2.813,2.573 0.302,0.375 10 false *2 0.802,0.229 1.094,0.542 0.292,0.313 10 false *a 0.385,3.208 0.813,3.521 0.427,0.313 10 false *b 1.323,1.135 1.823,1.469 0.5,0.333 10 false BBR- 2.292,1.135 2.844,1.406 0.552,0.271 10 false BBR+ 1.208,0.563 1.646,0.896 0.438,0.333 10 false M37 0.615,3.656 1.104,3.958 0.49,0.302 10 false M25 2.021,4.219 2.708,4.49 0.688,0.271 10 false BBR+ 1.115,4.229 1.656,4.521 0.542,0.292 10 false BBR- 1.292,1.917 1.646,2.25 0.354,0.333 10 false *3 1.938,1.292 2.198,1.615 0.26,0.323 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
M25-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always 1 MΩ or higher
M25-4 (BBR+) - Body ground Always 1 MΩ or higher
M25-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

11.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

11.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)
a.
C256981C36
0.948,0.563 1.313,0.802 0.365,0.24 0.604,3.615 0.958,3.823 0.354,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.26,1.063 1.927,0.667 false 1.344,4.073 1.667,3.698 false 2.146,4.063 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 1,0.604 1.49,0.896 0.49,0.292 10 false M25 0.656,3.635 1.146,3.927 0.49,0.292 10 false M27 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

12.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

12.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1623 and B1628 are not output. A
DTC B1623 is output. B
DTC B1628 is output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

13.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

14.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

14.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)
a.
C256981C36
0.948,0.563 1.313,0.802 0.365,0.24 0.604,3.615 0.958,3.823 0.354,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.26,1.063 1.927,0.667 false 1.344,4.073 1.667,3.698 false 2.146,4.063 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 1,0.604 1.49,0.896 0.49,0.292 10 false M25 0.656,3.635 1.146,3.927 0.49,0.292 10 false M27 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

15.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

15.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the side No. 2 airbag sensor assembly RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1632 or B1633 is output. A
DTC B1637 or B1638 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

C

16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1632, B1633, B1637 and B1638 are not output. A
DTC B1632 or B1633 is output. B
DTC B1637 or B1638 is output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.



g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1622 is output. B
DTC B1627 is output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

18.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1642, B1643 or 81 is output. A
Current DTC B1623 or B1633 is output. B
Current DTC B1692 or B1693 is output. C
Current DTC B1622 or B1632 is output. D
Current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B1692, B1693 and 81 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then to on (IG) again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B1692, B1693 and 81 may be output at this time, but they are not related to this check.





A

19.CHECK CONNECTORS

B

26.CHECK HISTORY DTC

C

37.CHECK CONNECTORS

D

41.CHECK CURRENT DTC

E

19.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

20.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE WIRE HARNESS

20.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)
a.
C238391C24
0.958,0.469 1.313,0.719 0.354,0.25 0.427,3.552 0.781,3.781 0.354,0.229 1.573,3.688 1.948,4.125 false 1.448,3.677 1.063,4.115 false 1.573,2.427 1.573,1.865 1.573,1.865 1.417,1.865 false 1.635,0.813 1.271,1.052 false 1.76,0.823 2.125,1.052 false 1.708,1.094 1.708,1.271 false 1.052,2.417 1.51,2.76 0.458,0.344 10 false D 1.365,2.417 1.677,2.75 0.313,0.333 10 false C 1.708,2.417 2,2.729 0.292,0.313 10 false B 2.01,2.417 2.302,2.781 0.292,0.365 10 false A 0.688,2.417 1.156,2.75 0.469,0.333 10 false *1 2.5,2.135 2.771,2.479 0.271,0.344 10 false *2 0.635,0.188 0.906,0.438 0.271,0.25 10 false *a 0.354,3.198 0.74,3.531 0.385,0.333 10 false *b 2.01,1.063 2.51,1.302 0.5,0.24 10 false BBR- 1.094,1.063 1.563,1.281 0.469,0.219 10 false BBR+ 1.01,0.51 1.427,0.792 0.417,0.281 10 false M58 0.479,3.583 0.969,3.865 0.49,0.281 10 false M25 1.823,4.125 2.354,4.354 0.531,0.229 10 false BBR+ 0.896,4.125 1.406,4.354 0.51,0.229 10 false BBR- 1.25,1.792 1.781,2.156 0.531,0.365 10 false *3 1.635,1.292 1.865,1.531 0.229,0.24 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
M25-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always 1 MΩ or higher
M25-4 (BBR+) - Body ground Always 1 MΩ or higher
M25-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

21.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)
a.
C238392C30
0.469,3.542 0.833,3.792 0.365,0.25 0.948,0.542 1.302,0.792 0.354,0.25 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCR- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCR+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M54 1,0.583 1.594,0.958 0.594,0.375 10 false M25 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCR- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCR+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

22.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH - DOOR SIDE AIRBAG SENSOR RH)

NG

REPLACE FLOOR WIRE

22.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH - DOOR SIDE AIRBAG SENSOR RH)
a.
C238393C16
0.563,3.521 0.927,3.76 0.365,0.24 0.958,0.604 1.323,0.854 0.365,0.25 1.375,3.688 0.938,4.052 false 1.542,3.677 1.979,4.042 false 1.833,0.74 1.5,1.073 false 1.958,0.74 2.292,1.073 false 1.469,4.052 1.469,4.26 false 1.573,2.323 1.865,2.708 0.292,0.385 10 false D 1.729,2.323 2.01,2.719 0.281,0.396 10 false C 2.073,2.323 2.333,2.688 0.26,0.365 10 false B 2.385,2.323 2.615,2.573 0.229,0.25 10 false A 2.698,2.313 2.979,2.646 0.281,0.333 10 false *2 0.542,2.323 0.854,2.625 0.313,0.302 10 false *1 0.354,3.198 0.688,3.51 0.333,0.313 10 false *b 0.646,0.198 0.927,0.458 0.281,0.26 10 false *a 0.76,4.063 1.271,4.344 0.51,0.281 10 false BDR- 1.875,4.063 2.427,4.354 0.552,0.292 10 false BDR+ 0.635,3.552 1.104,3.833 0.469,0.281 10 false H12 1.021,0.646 1.458,0.927 0.438,0.281 10 false M54 2.198,1.083 2.656,1.344 0.458,0.26 10 false BDR- 1.323,1.083 1.854,1.385 0.531,0.302 10 false BDR+ 0.927,2.323 1.406,2.677 0.479,0.354 10 false F 1.229,2.323 1.677,2.719 0.448,0.396 10 false E 1.406,4.271 1.688,4.51 0.281,0.24 10 false *3
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
M54-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - M54-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - M54-2 (BDR-) Always 1 MΩ or higher
M54-1 (BDR+) - Body ground Always 1 MΩ or higher
M54-2 (BDR-) - Body ground Always 1 MΩ or higher




OK

23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

44.CHECK FRONT DOOR WIRE RH
23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly RH, door side airbag sensor RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

24.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

C

24.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

25.CHECK DOOR SIDE AIRBAG SENSOR RH

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

C

25.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly RH


Interchange the door side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

26.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTCs B1622 and B1632 are not output. A
History DTC B1622 is output. B
History DTC B1632 is output. C


HINT:

Codes other than history DTCs B1622 and B1632 may be output at this time, but they are not related to this check.




A

27.CHECK CURRENT DTC

B

42.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

C

43.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
27.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1623 is output. A
Current DTC B1633 is output. B


HINT:

Codes other than current DTCs B1623 and B1633 may be output at this time, but they are not related to this check.




A

28.CHECK CONNECTORS

B

33.CHECK CONNECTORS
28.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

29.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE WIRE HARNESS

29.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY RH)
a.
C238391C24
0.958,0.469 1.313,0.719 0.354,0.25 0.427,3.552 0.781,3.781 0.354,0.229 1.573,3.688 1.948,4.125 false 1.448,3.677 1.063,4.115 false 1.573,2.427 1.573,1.865 1.573,1.865 1.417,1.865 false 1.635,0.813 1.271,1.052 false 1.76,0.823 2.125,1.052 false 1.708,1.094 1.708,1.271 false 1.052,2.417 1.51,2.76 0.458,0.344 10 false D 1.365,2.417 1.677,2.75 0.313,0.333 10 false C 1.708,2.417 2,2.729 0.292,0.313 10 false B 2.01,2.417 2.302,2.781 0.292,0.365 10 false A 0.688,2.417 1.156,2.75 0.469,0.333 10 false *1 2.5,2.135 2.771,2.479 0.271,0.344 10 false *2 0.635,0.188 0.906,0.438 0.271,0.25 10 false *a 0.354,3.198 0.74,3.531 0.385,0.333 10 false *b 2.01,1.063 2.51,1.302 0.5,0.24 10 false BBR- 1.094,1.063 1.563,1.281 0.469,0.219 10 false BBR+ 1.01,0.51 1.427,0.792 0.417,0.281 10 false M58 0.479,3.583 0.969,3.865 0.49,0.281 10 false M25 1.823,4.125 2.354,4.354 0.531,0.229 10 false BBR+ 0.896,4.125 1.406,4.354 0.51,0.229 10 false BBR- 1.25,1.792 1.781,2.156 0.531,0.365 10 false *3 1.635,1.292 1.865,1.531 0.229,0.24 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
M25-3 (BBR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-4 (BBR+) - M25-3 (BBR-) Always 1 MΩ or higher
M25-4 (BBR+) - Body ground Always 1 MΩ or higher
M25-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

30.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

30.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)
a.
C238392C30
0.469,3.542 0.833,3.792 0.365,0.25 0.948,0.542 1.302,0.792 0.354,0.25 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCR- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCR+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M54 1,0.583 1.594,0.958 0.594,0.375 10 false M25 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCR- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCR+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

31.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH - DOOR SIDE AIRBAG SENSOR RH)

NG

REPLACE FLOOR WIRE

31.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH - DOOR SIDE AIRBAG SENSOR RH)
a.
C238393C16
0.563,3.521 0.927,3.76 0.365,0.24 0.958,0.604 1.323,0.854 0.365,0.25 1.375,3.688 0.938,4.052 false 1.542,3.677 1.979,4.042 false 1.833,0.74 1.5,1.073 false 1.958,0.74 2.292,1.073 false 1.469,4.052 1.469,4.26 false 1.573,2.323 1.865,2.708 0.292,0.385 10 false D 1.729,2.323 2.01,2.719 0.281,0.396 10 false C 2.073,2.323 2.333,2.688 0.26,0.365 10 false B 2.385,2.323 2.615,2.573 0.229,0.25 10 false A 2.698,2.313 2.979,2.646 0.281,0.333 10 false *2 0.542,2.323 0.854,2.625 0.313,0.302 10 false *1 0.354,3.198 0.688,3.51 0.333,0.313 10 false *b 0.646,0.198 0.927,0.458 0.281,0.26 10 false *a 0.76,4.063 1.271,4.344 0.51,0.281 10 false BDR- 1.875,4.063 2.427,4.354 0.552,0.292 10 false BDR+ 0.635,3.552 1.104,3.833 0.469,0.281 10 false H12 1.021,0.646 1.458,0.927 0.438,0.281 10 false M54 2.198,1.083 2.656,1.344 0.458,0.26 10 false BDR- 1.323,1.083 1.854,1.385 0.531,0.302 10 false BDR+ 0.927,2.323 1.406,2.677 0.479,0.354 10 false F 1.229,2.323 1.677,2.719 0.448,0.396 10 false E 1.406,4.271 1.688,4.51 0.281,0.24 10 false *3
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
M54-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - M54-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - M54-2 (BDR-) Always 1 MΩ or higher
M54-1 (BDR+) - Body ground Always 1 MΩ or higher
M54-2 (BDR-) - Body ground Always 1 MΩ or higher




OK

32.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

44.CHECK FRONT DOOR WIRE RH
32.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly RH, door side airbag sensor RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1623 is output. A
DTC B1628 is output. B
DTCs B1623 and B1628 are not output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

33.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

34.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)

NG

REPLACE FLOOR WIRE

34.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY RH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH)
a.
C238392C30
0.469,3.542 0.833,3.792 0.365,0.25 0.948,0.542 1.302,0.792 0.354,0.25 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCR- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCR+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M54 1,0.583 1.594,0.958 0.594,0.375 10 false M25 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCR- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCR+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
M25-2 (BCR-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M25-1 (BCR+) - M25-2 (BCR-) Always 1 MΩ or higher
M25-1 (BCR+) - Body ground Always 1 MΩ or higher
M25-2 (BCR-) - Body ground Always 1 MΩ or higher




OK

35.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

35.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the side No. 2 airbag sensor assembly RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

36.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

B

C

36.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

C

37.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

38.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH - DOOR SIDE AIRBAG SENSOR RH)

NG

REPLACE WIRE HARNESS

38.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH - DOOR SIDE AIRBAG SENSOR RH)
a.
C238393C16
0.563,3.521 0.927,3.76 0.365,0.24 0.958,0.604 1.323,0.854 0.365,0.25 1.375,3.688 0.938,4.052 false 1.542,3.677 1.979,4.042 false 1.833,0.74 1.5,1.073 false 1.958,0.74 2.292,1.073 false 1.469,4.052 1.469,4.26 false 1.573,2.323 1.865,2.708 0.292,0.385 10 false D 1.729,2.323 2.01,2.719 0.281,0.396 10 false C 2.073,2.323 2.333,2.688 0.26,0.365 10 false B 2.385,2.323 2.615,2.573 0.229,0.25 10 false A 2.698,2.313 2.979,2.646 0.281,0.333 10 false *2 0.542,2.323 0.854,2.625 0.313,0.302 10 false *1 0.354,3.198 0.688,3.51 0.333,0.313 10 false *b 0.646,0.198 0.927,0.458 0.281,0.26 10 false *a 0.76,4.063 1.271,4.344 0.51,0.281 10 false BDR- 1.875,4.063 2.427,4.354 0.552,0.292 10 false BDR+ 0.635,3.552 1.104,3.833 0.469,0.281 10 false H12 1.021,0.646 1.458,0.927 0.438,0.281 10 false M54 2.198,1.083 2.656,1.344 0.458,0.26 10 false BDR- 1.323,1.083 1.854,1.385 0.531,0.302 10 false BDR+ 0.927,2.323 1.406,2.677 0.479,0.354 10 false F 1.229,2.323 1.677,2.719 0.448,0.396 10 false E 1.406,4.271 1.688,4.51 0.281,0.24 10 false *3
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Connect the connectors that link the floor wire and front door wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
M54-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - M54-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 (BDR+) - M54-2 (BDR-) Always 1 MΩ or higher
M54-1 (BDR+) - Body ground Always 1 MΩ or higher
M54-2 (BDR-) - Body ground Always 1 MΩ or higher




OK

39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

NG

44.CHECK FRONT DOOR WIRE RH
39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Connect the connector to the door side airbag sensor RH.


b.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692 or B1693 is output. A
DTC B1697 or B1698 is output. B
DTCs B1692, B1693, B1697 and B1698 are not output. C


HINT:

Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

40.CHECK DOOR SIDE AIRBAG SENSOR RH

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

C

40.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly RH


Interchange the door side airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692 or B1693 is output. A
DTC B1697 or B1698 is output. B
DTCs B1692, B1693, B1697 and B1698 are not output. C


HINT:

Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

41.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1622 is output. A
Current DTC B1632 is output. B


HINT:

Codes other than current DTCs B1622 and B1632 may be output at this time, but they are not related to this check.




A

42.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

B

43.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
42.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C01
0.802,1.188 1.094,1.479 0.292,0.292 10 false *1 1.115,1.167 1.281,1.448 0.167,0.281 10 false D 1.271,1.167 1.458,1.438 0.188,0.271 10 false C 1.719,1.177 1.948,1.5 0.229,0.323 10 false B 1.875,1.177 2.094,1.396 0.219,0.219 10 false A 2.302,0.906 2.625,1.198 0.323,0.292 10 false *2
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

C

43.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1632 is output. A
DTC B1637 is output. B
DTCs B1632 and B1637 are not output. C


HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH

C

44.CHECK FRONT DOOR WIRE RH
a.
C238396C09
0.531,3.552 0.854,3.76 0.323,0.208 0.823,0.625 1.167,0.823 0.344,0.198 1.573,3.688 1.906,4.01 false 1.333,3.688 0.99,3.99 false 1.667,1.01 1.344,1.229 false 1.885,1.01 2.25,1.208 false 1.448,2.469 1.448,2.844 1.448,2.844 1.646,2.844 false 2.052,2.333 2.052,1.854 2.052,1.854 2.208,1.854 false 1.448,4.073 1.448,4.292 false 1.563,2.333 1.833,2.667 0.271,0.333 10 false D 1.823,2.333 2.063,2.615 0.24,0.281 10 false C 2.167,2.323 2.385,2.708 0.219,0.385 10 false B 2.458,2.323 2.729,2.688 0.271,0.365 10 false A 2.771,2.313 3.042,2.677 0.271,0.365 10 false *2 0.552,2.323 0.927,2.625 0.375,0.302 10 false *1 0.344,3.188 0.604,3.469 0.26,0.281 10 false *b 0.667,0.188 0.969,0.469 0.302,0.281 10 false *a 1.792,4.021 2.375,4.344 0.583,0.323 10 false BDR+ 0.813,4 1.354,4.281 0.542,0.281 10 false BDR- 0.583,3.573 0.979,3.979 0.396,0.406 10 false H12 0.865,0.646 1.271,0.958 0.406,0.313 10 false HM3 1.146,1.24 1.677,1.615 0.531,0.375 10 false BDR+ 2.156,1.219 2.635,1.427 0.479,0.208 10 false BDR- 2.26,1.771 2.698,2.052 0.438,0.281 10 false *4 0.948,2.323 1.198,2.667 0.25,0.344 10 false F 1.219,2.333 1.438,2.625 0.219,0.292 10 false E 1.708,2.771 2.031,3.073 0.323,0.302 10 false *3 1.365,4.323 1.667,4.594 0.302,0.271 10 false *5
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Floor Wire)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)


Disconnect the front door wire RH connector from the floor wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HM3-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
HM3-2 (BDR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HM3-1 (BDR+) - HM3-2 (BDR-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HM3-1 (BDR+) - HM3-2 (BDR-) Always 1 MΩ or higher
HM3-1 (BDR+) - Body ground Always 1 MΩ or higher
HM3-2 (BDR-) - Body ground Always 1 MΩ or higher




OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH