Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  B1648/82  Side Satellite Sensor Bus LH Initialization Incomplete  B1697/82  Lost Communication with Door Side Airbag Sensor LH  B1698/82  Door Side Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

w/o Occupant Classification System:

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

The side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
B1648/82
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Airbag sensor assembly




w/ Occupant Classification System:

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH.

The side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
B1648/82
B1697/82
B1698/82
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

Side No. 2 airbag sensor assembly LH malfunction

·

Door side airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

Side No. 2 airbag sensor assembly LH

·

Door side airbag sensor LH

·

Airbag sensor assembly




WIRING DIAGRAM

w/o Occupant Classification System:
C239250E92
0.552,4.698 0.854,4.844 0.302,0.146 10 false M24 0.552,4.875 1.781,5.208 1.229,0.333 10 false Side Airbag Sensor Assembly LH 3.042,4.875 4.51,5.219 1.469,0.344 10 false Side No. 2 Airbag Sensor Assembly LH 3.042,4.698 3.344,4.844 0.302,0.146 10 false M26 5.24,4.844 6.833,5.042 1.594,0.198 10 false Airbag Sensor Assembly 5.24,4.667 5.552,4.833 0.313,0.167 10 false M36 1.125,0.896 1.521,1.052 0.396,0.156 10 false BBL+ 1.583,0.792 1.688,0.948 0.104,0.156 10 false 4 1.156,1.792 1.521,1.948 0.365,0.156 10 false BBL- 5.563,0.896 5.958,1.052 0.396,0.156 10 false BBL+ 5.365,0.792 5.542,0.948 0.177,0.156 10 false 8 5.323,1.698 5.5,1.854 0.177,0.156 10 false 15 5.563,1.792 5.958,1.948 0.396,0.156 10 false BBL- 1.583,1.698 1.688,1.854 0.104,0.156 10 false 3 1.125,3.042 1.521,3.198 0.396,0.156 10 false BCL+ 1.583,2.948 1.688,3.104 0.104,0.156 10 false 1 2.927,3.833 3.031,3.99 0.104,0.156 10 false 1 1.146,3.938 1.521,4.094 0.375,0.156 10 false BCL- 3.073,3.042 3.469,3.198 0.396,0.156 10 false BCL+ 3.073,3.938 3.469,4.094 0.396,0.156 10 false BCL- 1.583,3.833 1.688,3.99 0.104,0.156 10 false 2 2.927,2.948 3.031,3.104 0.104,0.156 10 false 2

w/ Occupant Classification System:
B483593E04
5.313,0.427 6.073,0.74 0.76,0.313 10 false 24 5.313,1 6.073,1.313 0.76,0.313 10 false 23 5.5,4.698 6.26,5.01 0.76,0.313 10 false M57 5.5,4.844 7.083,5.177 1.583,0.333 10 false Airbag Sensor Assembly 5.552,0.542 6.313,0.854 0.76,0.313 10 false BBL+ 5.552,1.115 6.313,1.427 0.76,0.313 10 false BBL- 1.146,0.542 1.906,0.854 0.76,0.313 10 false BBL+ 1.146,1.115 1.906,1.427 0.76,0.313 10 false BBL- 1.146,1.698 1.906,2.01 0.76,0.313 10 false BCL+ 1.146,2.302 1.906,2.615 0.76,0.313 10 false BCL- 1.583,0.448 2.344,0.76 0.76,0.313 10 false 4 1.583,1.021 2.344,1.333 0.76,0.313 10 false 3 1.583,1.604 2.344,1.917 0.76,0.313 10 false 1 1.583,2.208 2.344,2.521 0.76,0.313 10 false 2 3.469,1.698 4.229,2.01 0.76,0.313 10 false BCL+ 3.469,2.302 4.229,2.615 0.76,0.313 10 false BCL- 3.292,1.615 4.052,1.927 0.76,0.313 10 false 4 3.292,2.208 4.052,2.521 0.76,0.313 10 false 3 0.552,2.625 1.313,2.938 0.76,0.313 10 false M24 0.552,2.792 2.688,3.146 2.135,0.354 10 false Side Airbag Sensor Assembly LH 3.292,3.688 4.052,4 0.76,0.313 10 false 1 3.292,4.229 4.052,4.542 0.76,0.313 10 false 2 3.469,3.813 4.229,4.125 0.76,0.313 10 false BDL+ 3.469,4.344 4.229,4.656 0.76,0.313 10 false BDL- 3.417,4.677 4.177,4.99 0.76,0.313 10 false M53 3.417,4.844 5.031,5.333 1.615,0.49 10 false Side No. 2 Airbag Sensor Assembly LH 2.354,3.792 3.115,4.104 0.76,0.313 10 false JM3 2.354,4.333 3.115,4.646 0.76,0.313 10 false JM3 2.458,3.604 3.219,3.917 0.76,0.313 10 false 1 2.458,4.135 3.219,4.448 0.76,0.313 10 false 2 1.135,3.802 1.896,4.115 0.76,0.313 10 false BDL+ 1.167,4.344 1.927,4.656 0.76,0.313 10 false BDL- 1.583,3.698 2.344,4.01 0.76,0.313 10 false 2 1.583,4.229 2.344,4.542 0.76,0.313 10 false 1 0.542,4.677 1.302,4.99 0.76,0.313 10 false J12 0.542,4.844 2.427,5.24 1.885,0.396 10 false Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o Occupant Classification System A
w/ Occupant Classification System B




A

2.CHECK CURRENT DTC

B

18.CHECK CURRENT DTC
2.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1647, B1648 or 82 is output. A
Current DTC B1628 is output. B
Current DTC B1637 or B1638 is output. C
Current DTC B1627 is output. D
Current DTCs B1627, B1628, B1637, B1638, B1647, B1648 and 82 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then to on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1648 and 82 may be output at this time, but they are not related to this check.





A

3.CHECK CONNECTORS

B

8.CHECK HISTORY DTC

C

13.CHECK CONNECTORS

D

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

E

3.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

4.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)
a.
C238225C17
1,0.552 1.375,0.802 0.375,0.25 0.417,3.615 0.792,3.844 0.375,0.229 1.521,3.729 1.198,4.115 false 1.646,3.729 1.969,4.115 false 1.531,2.25 1.531,1.771 1.531,1.771 1.365,1.771 false 2,1.125 2,1.323 false 1.938,0.667 1.49,1.146 false 2.135,0.885 2.479,1.146 false 0.948,2.26 1.427,2.635 0.479,0.375 10 false D 1.26,2.26 1.604,2.656 0.344,0.396 10 false C 1.708,2.26 2.073,2.604 0.365,0.344 10 false B 2.021,2.26 2.365,2.667 0.344,0.406 10 false A 0.635,2.26 1.042,2.646 0.406,0.385 10 false *1 2.438,2.271 2.75,2.656 0.313,0.385 10 false *2 0.75,0.292 1.146,0.729 0.396,0.438 10 false *a 0.313,3.177 0.719,3.51 0.406,0.333 10 false *b 1.323,1.167 1.802,1.469 0.479,0.302 10 false BBL+ 2.375,1.156 2.844,1.406 0.469,0.25 10 false BBL- 1.063,0.594 1.552,0.938 0.49,0.344 10 false M36 0.49,3.646 0.99,3.979 0.5,0.333 10 false M24 1.854,4.135 2.417,4.448 0.563,0.313 10 false BBL+ 1.042,4.125 1.604,4.406 0.563,0.281 10 false BBL- 1.198,1.688 1.563,1.979 0.365,0.292 10 false *3 1.927,1.354 2.208,1.688 0.281,0.333 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M24-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always 1 MΩ or higher
M24-4 (BBL+) - Body ground Always 1 MΩ or higher
M24-3 (BBL-) - Body ground Always 1 MΩ or higher




OK

5.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)
a.
C256981C37
0.948,0.563 1.313,0.802 0.365,0.24 0.604,3.615 0.958,3.823 0.354,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.25,1.052 1.927,0.667 false 1.333,4.073 1.667,3.698 false 2.146,4.052 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCL+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCL- 1.167,4.083 1.656,4.375 0.49,0.292 10 false BCL- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCL+ 1,0.604 1.49,0.896 0.49,0.292 10 false M24 0.656,3.635 1.146,3.927 0.49,0.292 10 false M26 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M24-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always 1 MΩ or higher
M24-1 (BCL+) - Body ground Always 1 MΩ or higher
M24-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

6.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

7.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

C

7.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. A
DTC B1647, B1648 or 82 is output. B
DTC B1642, B1643 or 81 is output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

8.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1627 is not output. A
History DTC B1627 is output. B


HINT:

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.




A

9.CHECK CONNECTORS

B

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
9.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

10.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)
a.
C238225C17
1,0.552 1.375,0.802 0.375,0.25 0.417,3.615 0.792,3.844 0.375,0.229 1.521,3.729 1.198,4.115 false 1.646,3.729 1.969,4.115 false 1.531,2.25 1.531,1.771 1.531,1.771 1.365,1.771 false 2,1.125 2,1.323 false 1.938,0.667 1.49,1.146 false 2.135,0.885 2.479,1.146 false 0.948,2.26 1.427,2.635 0.479,0.375 10 false D 1.26,2.26 1.604,2.656 0.344,0.396 10 false C 1.708,2.26 2.073,2.604 0.365,0.344 10 false B 2.021,2.26 2.365,2.667 0.344,0.406 10 false A 0.635,2.26 1.042,2.646 0.406,0.385 10 false *1 2.438,2.271 2.75,2.656 0.313,0.385 10 false *2 0.75,0.292 1.146,0.729 0.396,0.438 10 false *a 0.313,3.177 0.719,3.51 0.406,0.333 10 false *b 1.323,1.167 1.802,1.469 0.479,0.302 10 false BBL+ 2.375,1.156 2.844,1.406 0.469,0.25 10 false BBL- 1.063,0.594 1.552,0.938 0.49,0.344 10 false M36 0.49,3.646 0.99,3.979 0.5,0.333 10 false M24 1.854,4.135 2.417,4.448 0.563,0.313 10 false BBL+ 1.042,4.125 1.604,4.406 0.563,0.281 10 false BBL- 1.198,1.688 1.563,1.979 0.365,0.292 10 false *3 1.927,1.354 2.208,1.688 0.281,0.333 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M24-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always 1 MΩ or higher
M24-4 (BBL+) - Body ground Always 1 MΩ or higher
M24-3 (BBL-) - Body ground Always 1 MΩ or higher




OK

11.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

11.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)
a.
C256981C37
0.948,0.563 1.313,0.802 0.365,0.24 0.604,3.615 0.958,3.823 0.354,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.25,1.052 1.927,0.667 false 1.333,4.073 1.667,3.698 false 2.146,4.052 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCL+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCL- 1.167,4.083 1.656,4.375 0.49,0.292 10 false BCL- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCL+ 1,0.604 1.49,0.896 0.49,0.292 10 false M24 0.656,3.635 1.146,3.927 0.49,0.292 10 false M26 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M24-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always 1 MΩ or higher
M24-1 (BCL+) - Body ground Always 1 MΩ or higher
M24-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

12.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

12.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1623 and B1628 are not output. A
DTC B1628 is output. B
DTC B1623 is output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

13.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

14.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

14.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)
a.
C256981C37
0.948,0.563 1.313,0.802 0.365,0.24 0.604,3.615 0.958,3.823 0.354,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.25,1.052 1.927,0.667 false 1.333,4.073 1.667,3.698 false 2.146,4.052 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCL+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCL- 1.167,4.083 1.656,4.375 0.49,0.292 10 false BCL- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCL+ 1,0.604 1.49,0.896 0.49,0.292 10 false M24 0.656,3.635 1.146,3.927 0.49,0.292 10 false M26 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M24-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always 1 MΩ or higher
M24-1 (BCL+) - Body ground Always 1 MΩ or higher
M24-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

15.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

15.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connector to the side No. 2 airbag sensor assembly LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1637 or B1638 is output. A
DTC B1632 or B1633 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

C

16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1632, B1633, B1637 and B1638 are not output. A
DTC B1637 or B1638 is output. B
DTC B1632 or B1633 is output. C


HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

17.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.



g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1622 and B1627 are not output. A
DTC B1627 is output. B
DTC B1622 is output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



j.

Turn the power switch off.


k.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



l.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

18.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1647, B1648 or 82 is output. A
Current DTC B1628 or B1638 is output. B
Current DTC B1697 or B1698 is output. C
Current DTC B1627 or B1637 is output. D
Current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B1697, B1698 and 82 are not output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then to on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B1697, B1698 and 82 may be output at this time, but they are not related to this check.





A

19.CHECK CONNECTORS

B

26.CHECK HISTORY DTC

C

37.CHECK CONNECTORS

D

41.CHECK CURRENT DTC

E

19.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

20.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE WIRE HARNESS

20.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)
a.
C238398C26
0.75,0.51 1.094,0.74 0.344,0.229 0.406,3.667 0.771,3.917 0.365,0.25 1.479,3.792 1.156,4.177 false 1.604,3.792 1.927,4.177 false 1.563,2.208 1.563,1.729 1.563,1.729 1.396,1.729 false 2.01,1.177 2.01,1.302 false 1.938,0.854 1.5,1.115 false 2.063,0.854 2.51,1.115 false 1.052,2.188 1.281,2.469 0.229,0.281 10 false D 1.354,2.188 1.667,2.667 0.313,0.479 10 false C 1.698,2.188 2.021,2.594 0.323,0.406 10 false B 2,2.198 2.344,2.625 0.344,0.427 10 false A 0.698,2.177 0.99,2.604 0.292,0.427 10 false *1 2.49,2.51 2.885,2.979 0.396,0.469 10 false *2 0.635,0.177 0.927,0.469 0.292,0.292 10 false *a 0.375,3.271 0.708,3.635 0.333,0.365 10 false *b 2.396,1.115 2.865,1.406 0.469,0.292 10 false BBL+ 1.333,1.115 1.813,1.375 0.479,0.26 10 false BBL- 0.792,0.542 1.271,0.865 0.479,0.323 10 false M57 0.469,3.708 0.948,4.156 0.479,0.448 10 false M24 1.802,4.188 2.323,4.469 0.521,0.281 10 false BBL+ 1,4.198 1.49,4.531 0.49,0.333 10 false BBL- 1.24,1.656 1.625,2.042 0.385,0.385 10 false *3 1.948,1.323 2.188,1.667 0.24,0.344 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M24-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always 1 MΩ or higher
M24-4 (BBL+) - Body ground Always 1 MΩ or higher
M24-3 (BBL-) - Body ground Always 1 MΩ or higher




OK

21.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)
a.
C238392C31
0.469,3.542 0.833,3.792 0.365,0.25 0.948,0.542 1.302,0.792 0.354,0.25 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M53 1,0.583 1.594,0.958 0.594,0.375 10 false M24 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M24-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always 1 MΩ or higher
M24-1 (BCL+) - Body ground Always 1 MΩ or higher
M24-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

22.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH - DOOR SIDE AIRBAG SENSOR LH)

NG

REPLACE FLOOR WIRE

22.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH - DOOR SIDE AIRBAG SENSOR LH)
a.
C238393C17
0.563,3.521 0.927,3.76 0.365,0.24 0.958,0.604 1.323,0.854 0.365,0.25 1.375,3.688 0.938,4.052 false 1.542,3.677 1.979,4.042 false 1.833,0.74 1.5,1.073 false 1.958,0.74 2.292,1.073 false 1.469,4.052 1.469,4.26 false 1.573,2.323 1.865,2.708 0.292,0.385 10 false D 1.729,2.323 2.01,2.719 0.281,0.396 10 false C 2.073,2.323 2.333,2.688 0.26,0.365 10 false B 2.385,2.323 2.615,2.573 0.229,0.25 10 false A 2.698,2.313 2.979,2.646 0.281,0.333 10 false *2 0.542,2.323 0.854,2.625 0.313,0.302 10 false *1 0.354,3.198 0.688,3.51 0.333,0.313 10 false *b 0.646,0.198 0.927,0.458 0.281,0.26 10 false *a 0.781,4.063 1.292,4.344 0.51,0.281 10 false BDL- 1.875,4.063 2.427,4.354 0.552,0.292 10 false BDL+ 0.646,3.552 1.177,3.938 0.531,0.385 10 false J12 1.021,0.646 1.458,0.927 0.438,0.281 10 false M53 2.198,1.083 2.656,1.344 0.458,0.26 10 false BDL- 1.333,1.083 1.865,1.385 0.531,0.302 10 false BDL+ 0.927,2.323 1.406,2.677 0.479,0.354 10 false F 1.229,2.323 1.677,2.719 0.448,0.396 10 false E 1.406,4.271 1.688,4.51 0.281,0.24 10 false *3
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly LH
*3 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - Body ground Power switch on (IG) Below 1 V
M53-2 (BDL-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - M53-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - M53-2 (BDL-) Always 1 MΩ or higher
M53-1 (BDL+) - Body ground Always 1 MΩ or higher
M53-2 (BDL-) - Body ground Always 1 MΩ or higher




OK

23.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

44.CHECK FRONT DOOR WIRE LH
23.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly LH, door side airbag sensor LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

24.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

C

24.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

25.CHECK DOOR SIDE AIRBAG SENSOR LH

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

C

25.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

26.CHECK HISTORY DTC

Result:
Result Proceed to
History DTCs B1627 and B1637 are not output. A
History DTC B1627 is output. B
History DTC B1637 is output. C


HINT:

Codes other than history DTCs B1627 and B1637 may be output at this time, but they are not related to this check.



A

27.CHECK CURRENT DTC

B

42.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

C

43.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
27.CHECK CURRENT DTC

Result:
Result Proceed to
Current DTC B1628 is output. A
Current DTC B1638 is output. B


HINT:

Codes other than current DTCs B1628 and B1638 may be output at this time, but they are not related to this check.



A

28.CHECK CONNECTORS

B

33.CHECK CONNECTORS
28.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH, side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

29.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE WIRE HARNESS

29.CHECK FLOOR WIRE (AIRBAG SENSOR ASSEMBLY - SIDE AIRBAG SENSOR ASSEMBLY LH)
a.
C238398C26
0.75,0.51 1.094,0.74 0.344,0.229 0.406,3.667 0.771,3.917 0.365,0.25 1.479,3.792 1.156,4.177 false 1.604,3.792 1.927,4.177 false 1.563,2.208 1.563,1.729 1.563,1.729 1.396,1.729 false 2.01,1.177 2.01,1.302 false 1.938,0.854 1.5,1.115 false 2.063,0.854 2.51,1.115 false 1.052,2.188 1.281,2.469 0.229,0.281 10 false D 1.354,2.188 1.667,2.667 0.313,0.479 10 false C 1.698,2.188 2.021,2.594 0.323,0.406 10 false B 2,2.198 2.344,2.625 0.344,0.427 10 false A 0.698,2.177 0.99,2.604 0.292,0.427 10 false *1 2.49,2.51 2.885,2.979 0.396,0.469 10 false *2 0.635,0.177 0.927,0.469 0.292,0.292 10 false *a 0.375,3.271 0.708,3.635 0.333,0.365 10 false *b 2.396,1.115 2.865,1.406 0.469,0.292 10 false BBL+ 1.333,1.115 1.813,1.375 0.479,0.26 10 false BBL- 0.792,0.542 1.271,0.865 0.479,0.323 10 false M57 0.469,3.708 0.948,4.156 0.479,0.448 10 false M24 1.802,4.188 2.323,4.469 0.521,0.281 10 false BBL+ 1,4.198 1.49,4.531 0.49,0.333 10 false BBL- 1.24,1.656 1.625,2.042 0.385,0.385 10 false *3 1.948,1.323 2.188,1.667 0.24,0.344 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - Body ground Power switch on (IG) Below 1 V
M24-3 (BBL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-4 (BBL+) - M24-3 (BBL-) Always 1 MΩ or higher
M24-4 (BBL+) - Body ground Always 1 MΩ or higher
M24-3 (BBL-) - Body ground Always 1 MΩ or higher




OK

30.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

30.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)
a.
C238392C31
0.469,3.542 0.833,3.792 0.365,0.25 0.948,0.542 1.302,0.792 0.354,0.25 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M53 1,0.583 1.594,0.958 0.594,0.375 10 false M24 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M24-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always 1 MΩ or higher
M24-1 (BCL+) - Body ground Always 1 MΩ or higher
M24-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

31.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH - DOOR SIDE AIRBAG SENSOR LH)

NG

REPLACE FLOOR WIRE

31.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH - DOOR SIDE AIRBAG SENSOR LH)
a.
C238393C17
0.563,3.521 0.927,3.76 0.365,0.24 0.958,0.604 1.323,0.854 0.365,0.25 1.375,3.688 0.938,4.052 false 1.542,3.677 1.979,4.042 false 1.833,0.74 1.5,1.073 false 1.958,0.74 2.292,1.073 false 1.469,4.052 1.469,4.26 false 1.573,2.323 1.865,2.708 0.292,0.385 10 false D 1.729,2.323 2.01,2.719 0.281,0.396 10 false C 2.073,2.323 2.333,2.688 0.26,0.365 10 false B 2.385,2.323 2.615,2.573 0.229,0.25 10 false A 2.698,2.313 2.979,2.646 0.281,0.333 10 false *2 0.542,2.323 0.854,2.625 0.313,0.302 10 false *1 0.354,3.198 0.688,3.51 0.333,0.313 10 false *b 0.646,0.198 0.927,0.458 0.281,0.26 10 false *a 0.781,4.063 1.292,4.344 0.51,0.281 10 false BDL- 1.875,4.063 2.427,4.354 0.552,0.292 10 false BDL+ 0.646,3.552 1.177,3.938 0.531,0.385 10 false J12 1.021,0.646 1.458,0.927 0.438,0.281 10 false M53 2.198,1.083 2.656,1.344 0.458,0.26 10 false BDL- 1.333,1.083 1.865,1.385 0.531,0.302 10 false BDL+ 0.927,2.323 1.406,2.677 0.479,0.354 10 false F 1.229,2.323 1.677,2.719 0.448,0.396 10 false E 1.406,4.271 1.688,4.51 0.281,0.24 10 false *3
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly LH
*3 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - Body ground Power switch on (IG) Below 1 V
M53-2 (BDL-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - M53-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - M53-2 (BDL-) Always 1 MΩ or higher
M53-1 (BDL+) - Body ground Always 1 MΩ or higher
M53-2 (BDL-) - Body ground Always 1 MΩ or higher




OK

32.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

44.CHECK FRONT DOOR WIRE LH
32.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the side No. 2 airbag sensor assembly LH, door side airbag sensor LH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1628 is output. A
DTC B1623 is output. B
DTCs B1623 and B1628 are not output. C


HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

33.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

34.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)

NG

REPLACE FLOOR WIRE

34.CHECK FLOOR WIRE (SIDE AIRBAG SENSOR ASSEMBLY LH - SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH)
a.
C238392C31
0.469,3.542 0.833,3.792 0.365,0.25 0.948,0.542 1.302,0.792 0.354,0.25 1.823,0.708 1.49,1.031 false 1.948,0.708 2.281,1.031 false 1.708,2.344 1.708,1.865 1.708,1.865 1.531,1.865 false 1.542,3.656 1.208,4.031 false 1.646,3.667 2,4.031 false 1.594,4.031 1.594,4.313 false 1.177,2.323 1.406,2.677 0.229,0.354 10 false D 1.479,2.323 1.781,2.594 0.302,0.271 10 false C 1.833,2.313 2.073,2.667 0.24,0.354 10 false B 2.146,2.313 2.406,2.698 0.26,0.385 10 false A 0.792,2.323 1.219,2.563 0.427,0.24 10 false *1 0.625,0.188 0.948,0.521 0.323,0.333 10 false *a 0.354,3.208 0.76,3.563 0.406,0.354 10 false *b 1.031,4.042 1.49,4.313 0.458,0.271 10 false BCL- 1.896,4.052 2.406,4.313 0.51,0.26 10 false BCL+ 0.531,3.583 0.948,3.906 0.417,0.323 10 false M53 1,0.583 1.594,0.958 0.594,0.375 10 false M24 2.188,1.042 2.688,1.323 0.5,0.281 10 false BCL- 1.313,1.052 1.865,1.365 0.552,0.313 10 false BCL+ 1.375,1.792 1.74,2.156 0.365,0.365 10 false *3 2.448,2.323 2.74,2.698 0.292,0.375 10 false *2 1.531,4.333 1.802,4.594 0.271,0.26 10 false *4
*1 Side No. 2 Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - Body ground Power switch on (IG) Below 1 V
M24-2 (BCL-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always Below 1 Ω



h.

Disconnect the service wire from connector C.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M24-1 (BCL+) - M24-2 (BCL-) Always 1 MΩ or higher
M24-1 (BCL+) - Body ground Always 1 MΩ or higher
M24-2 (BCL-) - Body ground Always 1 MΩ or higher




OK

35.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE FLOOR WIRE

35.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Connect the connector to the side No. 2 airbag sensor assembly LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

36.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

B

C

36.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

C

37.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side No. 2 airbag sensor assembly LH and door side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

38.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH - DOOR SIDE AIRBAG SENSOR LH)

NG

REPLACE WIRE HARNESS

38.CHECK WIRE HARNESS (SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH - DOOR SIDE AIRBAG SENSOR LH)
a.
C238393C17
0.563,3.521 0.927,3.76 0.365,0.24 0.958,0.604 1.323,0.854 0.365,0.25 1.375,3.688 0.938,4.052 false 1.542,3.677 1.979,4.042 false 1.833,0.74 1.5,1.073 false 1.958,0.74 2.292,1.073 false 1.469,4.052 1.469,4.26 false 1.573,2.323 1.865,2.708 0.292,0.385 10 false D 1.729,2.323 2.01,2.719 0.281,0.396 10 false C 2.073,2.323 2.333,2.688 0.26,0.365 10 false B 2.385,2.323 2.615,2.573 0.229,0.25 10 false A 2.698,2.313 2.979,2.646 0.281,0.333 10 false *2 0.542,2.323 0.854,2.625 0.313,0.302 10 false *1 0.354,3.198 0.688,3.51 0.333,0.313 10 false *b 0.646,0.198 0.927,0.458 0.281,0.26 10 false *a 0.781,4.063 1.292,4.344 0.51,0.281 10 false BDL- 1.875,4.063 2.427,4.354 0.552,0.292 10 false BDL+ 0.646,3.552 1.177,3.938 0.531,0.385 10 false J12 1.021,0.646 1.458,0.927 0.438,0.281 10 false M53 2.198,1.083 2.656,1.344 0.458,0.26 10 false BDL- 1.333,1.083 1.865,1.385 0.531,0.302 10 false BDL+ 0.927,2.323 1.406,2.677 0.479,0.354 10 false F 1.229,2.323 1.677,2.719 0.448,0.396 10 false E 1.406,4.271 1.688,4.51 0.281,0.24 10 false *3
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly LH
*3 Service Wire
*a Front view of wire harness connector
(to Side No. 2 Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Connect the connectors that link the floor wire and front door wire LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - Body ground Power switch on (IG) Below 1 V
M53-2 (BDL-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - M53-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M53-1 (BDL+) - M53-2 (BDL-) Always 1 MΩ or higher
M53-1 (BDL+) - Body ground Always 1 MΩ or higher
M53-2 (BDL-) - Body ground Always 1 MΩ or higher




OK

39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

NG

44.CHECK FRONT DOOR WIRE LH
39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Connect the connector to the door side airbag sensor LH.


b.

Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1697 or B1698 is output. A
DTC B1692 or B1693 is output. B
DTCs B1692, B1693, B1697 and B1698 are not output. C


HINT:

Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

40.CHECK DOOR SIDE AIRBAG SENSOR LH

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

C

40.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C238395C02
0.719,1.021 1.51,1.656 0.792,0.635 10 false *1 2.552,1 2.906,1.406 0.354,0.406 10 false *2 2.26,1.021 2.531,1.51 0.271,0.49 10 false A 2.104,1.021 2.531,1.563 0.427,0.542 10 false B 1.76,1.021 2.24,1.583 0.479,0.563 10 false C 1.604,1.021 2.031,1.615 0.427,0.594 10 false D 1.26,1.021 1.708,1.625 0.448,0.604 10 false E 1.115,1.021 1.792,1.771 0.677,0.75 10 false F
*1 Door Side Airbag Sensor RH
*2 Side No. 2 Airbag Sensor Assembly LH


Interchange the door side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1697 or B1698 is output. A
DTC B1692 or B1693 is output. B
DTCs B1692, B1693, B1697 and B1698 are not output. C


HINT:

Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

41.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1627 is output. A
Current DTC B1637 is output. B


HINT:

Codes other than current DTCs B1627 and B1637 may be output at this time, but they are not related to this check.




A

42.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

B

43.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
42.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1627 is output. A
DTC B1622 is output. B
DTCs B1622 and B1627 are not output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

C

43.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1637 is output. A
DTC B1632 is output. B
DTCs B1632 and B1637 are not output. C


HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

C

44.CHECK FRONT DOOR WIRE LH
a.
C238396C10
0.531,3.552 0.854,3.76 0.323,0.208 0.823,0.625 1.167,0.823 0.344,0.198 1.573,3.688 1.906,4.01 false 1.333,3.688 0.99,3.99 false 1.667,1.01 1.344,1.229 false 1.885,1.01 2.25,1.208 false 1.448,2.469 1.448,2.844 1.448,2.844 1.646,2.844 false 2.052,2.333 2.052,1.854 2.052,1.854 2.208,1.854 false 1.448,4.073 1.448,4.292 false 1.563,2.333 1.833,2.667 0.271,0.333 10 false D 1.823,2.333 2.063,2.615 0.24,0.281 10 false C 2.167,2.323 2.385,2.708 0.219,0.385 10 false B 2.458,2.323 2.729,2.688 0.271,0.365 10 false A 2.771,2.313 3.042,2.677 0.271,0.365 10 false *2 0.552,2.323 0.927,2.625 0.375,0.302 10 false *1 0.344,3.188 0.604,3.469 0.26,0.281 10 false *b 0.667,0.188 0.969,0.469 0.302,0.281 10 false *a 1.802,4.021 2.385,4.344 0.583,0.323 10 false BDL+ 0.833,4 1.375,4.281 0.542,0.281 10 false BDL- 0.594,3.573 0.99,3.979 0.396,0.406 10 false J12 0.875,0.646 1.281,0.958 0.406,0.313 10 false JM3 1.146,1.24 1.677,1.615 0.531,0.375 10 false BDL+ 2.156,1.219 2.635,1.427 0.479,0.208 10 false BDL- 2.26,1.771 2.698,2.052 0.438,0.281 10 false *4 0.948,2.323 1.198,2.667 0.25,0.344 10 false F 1.219,2.333 1.438,2.625 0.219,0.292 10 false E 1.708,2.771 2.031,3.073 0.323,0.302 10 false *3 1.365,4.323 1.667,4.594 0.302,0.271 10 false *5
*1 Door Side Airbag Sensor LH
*2 Side No. 2 Airbag Sensor Assembly LH
*3 Front Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Floor Wire)
*b Front view of wire harness connector
(to Door Side Airbag Sensor LH)


Disconnect the front door wire LH connector from the floor wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
JM3-1 (BDL+) - Body ground Power switch on (IG) Below 1 V
JM3-2 (BDL-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM3-1 (BDL+) - JM3-2 (BDL-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
JM3-1 (BDL+) - JM3-2 (BDL-) Always 1 MΩ or higher
JM3-1 (BDL+) - Body ground Always 1 MΩ or higher
JM3-2 (BDL-) - Body ground Always 1 MΩ or higher




OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE LH