Home › Engine / Hybrid System › 1NZ-FXE INTAKE / EXHAUST › EXHAUST PIPE › from 2017.06
RM2170E _51 Engine / Hybrid System _057008 1NZ-FXE INTAKE / EXHAUST _0277970 EXHAUST PIPE A

1NZ-FXE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (w/ Exhaust Heat Recirculation System)

NOTICE:

When installing the heater water hose, ensure that the exhaust heat recirculation system is filled with coolant. Otherwise, the engine water pump assembly may be damaged.


a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 41.5 mm (1.64 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new gasket to the exhaust manifold (TWC: Front Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



f.

Connect the 2 heater water hoses and slide the 2 clips to secure them.


Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (w/o Exhaust Heat Recirculation System)

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 41.5 mm (1.64 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new gasket to the exhaust manifold (TWC: Front Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the exhaust manifold (TWC: Front Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the 3 exhaust pipe supports.


e.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold (TWC: Front Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C18
2.406,0.771 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.156,0.594 false 0.771,1.198 0.927,1.198 0.927,1.198 1.094,0.896 false 0.406,1.417 0.615,1.573 0.208,0.156 10 *a 0.573,0.146 0.823,0.302 0.25,0.156 10 *1 0.573,1.125 0.813,1.313 0.24,0.188 10 *2 2.698,0.083 2.927,0.26 0.229,0.177 10 *3
*1 Exhaust Manifold (TWC: Front Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 8.5 mm (0.335 in.)


After installation, check that the space between the flanges of the exhaust manifold (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.



Hide 17430 3.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A077857

Using a vernier caliper, measure the free length of the compression springs.

Minimum Free Length 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install a new gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C59
2.927,1.438 2.802,1.438 2.802,1.438 2.5,1.75 false 1.656,3.219 2.031,3.219 2.031,3.219 2.031,2.438 false 1.458,0.656 1.813,0.656 1.813,0.656 1.813,1.115 false 1.313,0.563 1.604,0.781 0.292,0.219 10 false *1 3.031,1.333 3.313,1.542 0.281,0.208 10 false *a 1.438,3.146 1.76,3.385 0.323,0.24 10 false *2
*1 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the gasket until its surface is flush with the front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

Do not push in the gasket by using the exhaust pipe when connecting it.




d.

Connect the tail exhaust pipe assembly to the 2 exhaust pipe supports.


e.

Install the tail exhaust pipe assembly to the front exhaust pipe assembly (TWC: Rear Catalyst) with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258966C30
1.365,0.938 1.094,0.406 1.094,0.406 0.896,0.406 false 1.333,1.167 1.125,1.51 1.125,1.51 0.938,1.51 false 2.24,0.948 2.625,0.448 2.625,0.448 2.823,0.448 true 0.719,0.323 0.875,0.469 0.156,0.146 10 false *1 0.76,1.427 0.917,1.573 0.156,0.146 10 false *2 2.844,0.365 3,0.51 0.156,0.146 10 false *3 0.625,1.74 0.823,2 0.198,0.26 10 false *a
*1 Tail Exhaust Pipe Assembly
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*3 Gasket
*a Space between Flanges: 6.5 mm (0.256 in.)


After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.



Hide 4.ADD COOLANT (for Engine) (w/ Exhaust Heat Recirculation System)

Hide 5.INSPECT FOR COOLANT LEAK (for Engine) (w/ Exhaust Heat Recirculation System)

Hide 6.INSPECT FOR EXHAUST GAS LEAK