Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) D

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  FREEZE FRAME DATA  


DESCRIPTION


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

HINT:

If it is impossible to replicate the problem even though a DTC is detected, confirm the freeze frame data.



A317524E18
0.375,1.135 2.063,1.333 1.688,0.198 10 false 0.5 seconds 1.302,1.135 2.99,1.333 1.688,0.198 10 false 0.5 seconds 2.26,1.135 3.427,1.375 1.167,0.24 10 false 0.5 seconds 2.448,0.25 3.25,0.563 0.802,0.313 10 false DTC stored 0.396,2.792 3.271,3.063 2.875,0.271 10 false Freeze frame data which can be read

The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the GTS, 5 separate sets of freeze frame data can be checked.

-

3 data sets before the DTC was stored.

-

1 data set when the DTC was stored.

-

1 data set after the DTC was stored.


These data sets can be used to simulate the condition of the vehicle around the time of the occurrence the malfunction. The data may assist in identifying the cause of the malfunction, and judging whether it was temporary or not.




PENDING FREEZE FRAME DATA


HINT:

Pending freeze frame data is stored when a 2 trip DTC is first detected during the first trip.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Select a DTC in order to display its pending freeze frame data.

HINT:
·

Pending freeze frame data is cleared when any of the following occurs.

-

Using the GTS, the DTCs cleared.


-

The cable is disconnected from the negative (-) auxiliary battery terminal.


-

40 trips with the engine fully warmed up have been performed after returning to normal. (Pending freeze frame data will not be cleared by only returning the system to normal.)


·

With previous pending freeze frame data stored, if pending freeze frame data is newly stored when a 2 trip DTC is detected in the first trip, the old freeze frame data will be replaced with the new one of the newly detected DTC in the next trip.



A410648E01
0.219,0.083 6.792,0.49 6.573,0.406 10 false When a DTC is detected in both the first and second trips but the system returns to normal from the third trip (2 trip logic DTC): 2.094,0.938 2.813,1.26 0.719,0.323 10 false (First Trip) 2.844,0.927 3.74,1.229 0.896,0.302 10 false (Second Trip) 3.771,0.938 4.552,1.26 0.781,0.323 10 false (Third Trip) 4.531,0.938 5.427,1.344 0.896,0.406 10 false (Fourth Trip) 0.146,1.688 1.177,2 1.031,0.313 10 false Power Switch 1.25,1.521 1.906,1.792 0.656,0.271 10 false On (IG) 1.5,1.896 1.833,2.125 0.333,0.229 10 false Off 0.083,2.583 1.052,3.031 0.969,0.448 10 false Pending Freeze Frame Data 1.313,2.51 2.229,2.708 0.917,0.198 10 false Stored 1.354,2.833 1.813,3.188 0.458,0.354 10 false Not Stored 0.188,3.813 1.052,4.25 0.865,0.438 10 false Freeze Frame Data 1.281,3.698 2.198,3.896 0.917,0.198 10 false Stored 1.292,4 1.708,4.438 0.417,0.438 10 false Not Stored 0.365,4.719 2.135,5 1.771,0.281 10 false :Malfunction detected 0.385,5.021 2.323,5.396 1.938,0.375 10 false :Malfunction not detected

A410649E01
0.208,0.083 6.719,0.385 6.51,0.302 10 false When 2 trip DTC is first detected in the first trip and another 2 trip DTC is first detected in the second trip: 2.656,0.813 3.469,1.125 0.813,0.313 10 false (First Trip) 3.531,0.802 4.479,1.104 0.948,0.302 10 false (Second Trip) 4.542,0.802 5.323,1.115 0.781,0.313 10 false (Third Trip) 5.458,0.771 6.354,1.063 0.896,0.292 10 false (Fourth Trip) 4.208,2.927 5.042,3.26 0.833,0.333 10 false Uploaded 0.719,4.156 2.958,4.458 2.24,0.302 10 false :Pending malfunction A detected 0.708,4.604 2.938,4.906 2.229,0.302 10 false :Pending malfunction B detected 0.688,5.104 2.438,5.427 1.75,0.323 10 false :No malfunction detected 0.635,1.594 1.656,1.896 1.021,0.302 10 false Power Switch 1.813,1.417 2.479,1.729 0.667,0.313 10 false On (IG) 1.844,1.792 2.302,2.083 0.458,0.292 10 false Off 0.521,2.417 1.51,2.865 0.99,0.448 10 false Pending Freeze Frame Data A 1.844,2.271 2.438,2.615 0.594,0.344 10 false Stored 1.865,2.573 2.302,2.969 0.438,0.396 10 false Not Stored 0.458,3.292 1.448,3.802 0.99,0.51 10 false Pending Freeze Frame Data B 1.802,3.188 2.354,3.458 0.552,0.271 10 false Stored 1.854,3.521 2.281,3.896 0.427,0.375 10 false Not Stored



LIST OF FREEZE FRAME DATA


Refer to "Data List / Active Test".

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST