Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P148F  Engine Coolant Pump Over Revolution  


MONITOR DESCRIPTION

The ECM controls the engine water pump assembly by calculating the necessary amount of coolant flow based on engine coolant temperature, engine speed and vehicle speed information. The speed of the engine water pump assembly is controlled steplessly using a duty cycle signal sent from the ECM. This optimal control enhances warm-up performance and reduces cooling losses, thus reducing the specific fuel consumption of the engine. The ECM monitors the speed of the engine water pump assembly and stores a DTC when it determines that the engine water pump assembly rotates excessively based on the fact that the actual speed is higher than the target for a certain amount of time. (However, the MIL will not illuminate.)

DTC No. DTC Detection Condition Trouble Area
P148F When both of the following conditions are met for 5 seconds or more (1 trip detection logic):
·

Engine water pump assembly duty ratio is 85% or higher.

·

Actual engine water pump assembly speed exceeds the target for a certain amount of time.


·

Lack of engine coolant

·

Engine coolant leak

·

Engine water pump assembly



CAUTION / NOTICE / HINT

HINT:
·

DTC P148F may be stored if the engine has continuously run with insufficient engine coolant. If the engine coolant is sufficient and DTC P148F recur when the vehicle is brought to the workshop, confirm whether engine coolant was added after the vehicle had been driven with insufficient engine coolant.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P148F)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P148F is output A
DTC P148F and other DTCs are output B

HINT:

If any DTCs other than P148F are output, troubleshoot those DTCs first.




A

2.CHECK RADIATOR RESERVOIR TANK ASSEMBLY (ENGINE COOLANT LEVEL)

B

2.CHECK RADIATOR RESERVOIR TANK ASSEMBLY (ENGINE COOLANT LEVEL)
a.

Check that the engine coolant level is between the FULL and LOW lines.

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION

Result
Result Proceed to
Engine coolant level is below the LOW line A
Engine coolant level is above the LOW line B



A

3.CHECK FOR ENGINE COOLANT LEAKS

B

6.CLEAR DTC (DTC P148F)
3.CHECK FOR ENGINE COOLANT LEAKS
a.

Check the areas around the engine and heater for engine coolant leaks.

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>COOLING SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks.


HINT:

If the engine oil is cloudy during the engine oil level gauge check, it means that engine coolant has entered the engine lubrication system.




OK

4.ADD ENGINE COOLANT

NG

5.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
4.ADD ENGINE COOLANT
a.

Fill the reservoir tank up to the FULL line with engine coolant.

NOTICE:

Make sure not to add engine coolant when the engine is hot.




NEXT

6.CLEAR DTC (DTC P148F)
5.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair any engine coolant leaks.

HINT:

Add engine coolant and perform air bleeding after repair.

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>COOLANT(for Engine)>REPLACEMENT




NEXT

6.CLEAR DTC (DTC P148F)
6.CLEAR DTC (DTC P148F)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.




NEXT

7.INSPECT ENGINE WATER PUMP ASSEMBLY
7.INSPECT ENGINE WATER PUMP ASSEMBLY
HINT:

Perform repair indoors or in a workshop.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp and Elec Water Pump Spd.

HINT:

Display the Data List diagram.



g.

Idle the engine for about 20 minutes and check Coolant Temp, Elec Water Pump Spd using the GTS, and check the cooling fans.

Result
Result Proceed to
One of the following conditions is met:
·

The engine coolant temperature becomes 95°C (203°F) or higher and the engine water pump assembly performs intermittent operation (5 seconds pause after 25 seconds operation).

·

The engine water pump assembly does not start operating even after the engine coolant temperature becomes 95°C (203°F) or higher.*1, *2

·

The ECM voltage is 15 V or less, and the Data List item Elec Water Pump Spd reaches 6375 rpm.


A
The cooling fans start operating after the engine coolant temperature becomes 95°C (203°F) or less and decrease in the engine coolant temperature is observed.*3 B

HINT:
·

*1: Be careful when the cooling fans do not start operating even after the engine coolant temperature becomes 95°C (203°F) or higher because the engine coolant temperature increases rapidly. (Make sure to stop the engine if the engine coolant temperature becomes 105°C (221°F) or higher.)

·

*2: If the ECM voltage is 14 V or higher and the engine water pump assembly is run excessively due to insufficient coolant etc., the water pump motor speed will exceed 5000 rpm. Enter the following menus to check the voltage of the ECM: Powertrain / Engine and ECT / Data List / Primary / Battery Voltage.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST

·

*3: When the engine is warmed up, the cooling fans operate and the engine coolant temperature will decrease. After the cooling fans begin operating, the engine coolant temperature will stabilize between 88 to 95°C (190 to 203°F).





A

8.REPLACE ENGINE WATER PUMP ASSEMBLY

B

END

8.REPLACE ENGINE WATER PUMP ASSEMBLY
a.

Replace the engine water pump assembly.

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>WATER PUMP>REMOVAL



NEXT

9.ADD ENGINE COOLANT
9.ADD ENGINE COOLANT
a.

Fill the reservoir tank up to the FULL line with engine coolant.

NOTICE:

Make sure not to add engine coolant when the engine is hot.




NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
HINT:

Perform repair indoors or in a workshop.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp and Elec Water Pump Spd.


h.

Idle the engine for about 20 minutes and check Coolant Temp, Elec Water Pump Spd using the GTS, and check the cooling fans.

Result:

The cooling fans start operating after the engine coolant temperature becomes 95°C (203°F) or less and decrease in the engine coolant temperature is observed.




NEXT

END