Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › from 2017.06
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U183374E02
1.948,0.708 2.365,0.906 0.417,0.198 10 false G77 3.313,0.719 3.635,0.917 0.323,0.198 10 false G78 4.875,0.708 5.24,0.906 0.365,0.198 10 false G79

a.

Disconnect the G77 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G77-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G77-2 (+B) - G77-11 (E) Input B - W-B +B power supply Power switch off 11 to 14 V -
G77-10 (CUTB) - G77-11 (E) Input L - W-B Dark current cut pin* Power switch off 11 to 14 V -

*: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).


If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.


c.

Reconnect the G77 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G79-5 (IG) - G77-11 (E) Input V - W-B IG power supply Power switch off → on (IG) Below 1 V → 11 to 14 V Engine Switch
G79-12 (CLG1) - G77-11 (E) Output L - W-B Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Driver Side (key diagnostic mode)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
G79-13 (CG1B) - G77-11 (E) Output P - W-B Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
G79-11 (CLG2) - G77-11 (E) Output L - W-B Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Passenger Side (key diagnostic mode)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
G79-10 (CG2B) - G77-11 (E) Output P - W-B Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
G79-3 (CLG5) - G77-11 (E) Output P - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
G79-2 (CG5B) - G77-11 (E) Output Y - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
G79-20 (TSW1) - G77-11 (E) Input LG - W-B Driver door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 5) D-Door Trigger Switch
G79-8 (TSW2) - G77-11 (E) Input LG - W-B Front passenger door lock sensor signal input
(Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched


Pulse generation (See waveform 5) P-Door Trigger Switch
G79-22 (SEN1) - G77-11 (E) Input BE - W-B Driver door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation (See waveform 5) D-Door Touch Sensor
G79-23 (SEN2) - G77-11 (E) Input R - W-B Front passenger door unlock sensor signal input
(when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation (See waveform 5) P-Door Touch Sensor
G78-27 (TSW5) - G77-11 (E) Input L - W-B Back door opener switch assembly (unlock switch) signal input Back door opener switch assembly (unlock switch) off → on Pulse generation (See waveform 5) Tr/B-Door Unlock SW
G78-28 (TSW6) - G77-11 (E) Input G - W-B Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch )off → on Pulse generation (See waveform 5) Tr/B-Door Lock SW
G78-11 (CLG6) - G77-11 (E) Output LG - W-B Output to No. 2 indoor electrical key antenna assembly (steering column) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
G78-10 (CG6B) - G77-11 (E) Output V*4 - W-B
SB*5 - W-B
Output to No. 2 indoor electrical key antenna assembly (steering column) (terminal on opposite side of component from CLG6 output terminal) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
G78-9 (CLG7) - G77-11 (E) Output W - W-B Output to No. 3 indoor electrical key antenna assembly (rear floor) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Back Door (inside) (key diagnostic mode)
G78-8 (CG7B) - G77-11 (E) Output BR - W-B Output to No. 3 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG7 output terminal) Proceed:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds


Pulse generation (See waveform 3) Over Head + Back Door (inside) (key diagnostic mode)
G79-19 (POS1) - G77-11 (E) Output W - W-B Driver door unlock sensor power source (12 V (drops when power switch turned on (IG))) Power switch off → on (IG) 9 to 14 V → Below 2 V -
G79-21 (POS2) - G77-11 (E) Output GR - W-B Front passenger door unlock sensor power source (12 V (drops when power switch turned on (IG))) Power switch off → on (IG) 9 to 14 V → Below 2 V -
G78-5 (RCO) - G77-11 (E) Output L - W-B Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 6) -
G78-17 (RDAS) - G77-11 (E)*6 Input LG - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Proceed:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 7) -
G78-17 (RDAM) - G77-11 (E)*7 Input LG - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock switches of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 8) -
G78-19 (RSSI) - G77-11 (E)*6 Output R*4 - W-B
P*5 - W-B
Door control receiver sends signal to certification ECU (smart key ECU assembly) indicating whether electric waves (example: 312 MHz) from key are being received or not (receiver grounds 12 V signal from certification ECU (smart key ECU assembly)) Procedure:
1.

All door closed

2.

All door locked

3.

Electrical key transmitter sub-assembly switch not pressed → pressed


11 to 14 V → Below 2 V Key diagnostic mode
G78-6 (CSEL) - G77-11 (E)*8 Output R - W-B Communication channel switching circuit. Procedure:
1.

Power switch off

2.

All doors closed


Below 1 V → Pulse generation Key diagnostic mode
G78-2 (CLG8) - G77-11 (E) Output V - W-B Output to electrical key antenna (outside luggage) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation (See waveform 4) Over Head + Back Door
or
Luggage + Back Door (key diagnostic mode)
G78-1 (CG8B) - G77-11 (E) Output L - W-B Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation (See waveform 4) Over Head + Back Door
or
Luggage + Back Door (key diagnostic mode)

*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

*4: for LHD

*5: for RHD

*6: w/o Tire Pressure Warning System

*7: w/ Tire Pressure Warning System

*8: w/ Tire Pressure Warning System without Panic Function



e.
B251021E01
0.103,0.932 0.433,1.125 0.330,0.194 10 GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection G79-12 (CLG1) - G77-11 (E)
G79-11 (CLG2) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought inside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



f.
B251024E01
0.103,0.984 0.433,1.178 0.330,0.194 10 GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection G79-12 (CLG1) - G77-11 (E)
G79-11 (CLG2) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).


Waveform 2 (Reference)
Item Content
Tester Connection G79-13 (CG1B) - G77-11 (E)
G79-10 (CG2B) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Electrical key transmitter sub-assembly not inside vehicle

5.

Electrical key transmitter sub-assembly brought outside detection area*

6.

All doors locked through wireless operation



*: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



g.
B251020E01
0.843,1.835 1.033,2.041 0.190,0.206 10 *a 1.748,1.835 1.938,2.041 0.190,0.206 10 *b 0.103,0.916 0.433,1.110 0.330,0.194 10 GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Door open
*b After approximately 30 seconds from when the door is closed

Waveform 3 (Reference)
Item Content
Tester Connection G79-3 (CLG5) - G77-11 (E)
G79-2 (CG5B) - G77-11 (E)
G78-11 (CLG6) - G77-11 (E)
G78-10 (CG6B) - G77-11 (E)
G78-9 (CLG7) - G77-11 (E)
G78-8 (CG7B) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Door is open

4.

Door is closed

5.

Within 30 seconds




h.
B449962E01
1.271,1.948 1.271,1.219 true 0.177,1.01 0.635,1.208 0.458,0.198 10 false GND 1.208,1.958 1.667,2.156 0.458,0.198 10 false *a

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Power switch off, all doors closed and back door opener switch assembly off → on

Waveform 4 (Reference)
Item Content
Tester Connection G78-2 (CLG8) - G77-11 (E)
G78-1 (CG8B) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on




i.
B251023E20
1.323,0.49 1.979,0.125 1.979,0.125 2.198,0.125 false 1.979,0.125 1.729,0.5 false 0.177,1.188 0.51,1.385 0.333,0.198 10 false GND 2.292,0.083 2.469,0.26 0.177,0.177 10 false *a

Using an oscilloscope, check waveform 5.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a In actuality, sampling is being performed

Waveform 5 (Reference)
Item Content
Tester Connection G79-20 (TSW1) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection G79-8 (TSW2) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection G79-22 (SEN1) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection G79-23 (SEN2) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Tester Connection G78-27 (TSW5) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Back door opener switch assembly (unlock switch) off → on

Waveform 5 (Reference)
Item Content
Tester Connection G78-28 (TSW6) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Back door opener switch assembly (lock switch) off → on


j.
B251178E01
0.103,0.984 0.433,1.178 0.330,0.194 10 GND 0.97,1.886 1.153,2.044 0.183,0.158 10 *a 2.01,1.886 2.192,2.044 0.183,0.158 10 *b

Using an oscilloscope, check waveform 6.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed

Waveform 6 (Reference)
Item Content
Tester Connection G78-5 (RCO) - G77-11 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).



k.
B251177E01
0.103,0.984 0.433,1.178 0.330,0.194 10 GND 0.984,1.878 1.167,2.037 0.183,0.158 10 *a 2.2,1.878 2.383,2.037 0.183,0.158 10 *b

Using an oscilloscope, check waveform 7.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed

Waveform 7 (Reference)
Item Content
Tester Connection G78-17 (RDAS) - G77-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Proceed:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).



l.
B251177E01
0.103,0.984 0.433,1.178 0.330,0.194 10 GND 0.984,1.878 1.167,2.037 0.183,0.158 10 *a 2.2,1.878 2.383,2.037 0.183,0.158 10 *b

Using an oscilloscope, check waveform 8.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock switches of electrical key transmitter sub-assembly pressed
*b After lock or unlock switches of electrical key transmitter sub-assembly pressed

Waveform 8 (Reference)
Item Content
Tester Connection G78-17 (RDAM) - G77-11 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock switches of electrical key transmitter sub-assembly not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).




CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U183415E05
4.052,1.031 4.052,0.625 4.052,0.625 4.167,0.625 false 1.677,1.417 1.927,1.417 false 0.729,2.677 1.042,2.677 false 1.625,0.854 1.625,0.427 1.625,0.427 1.802,0.427 false 4.219,0.552 4.583,0.729 0.365,0.177 10 false MB 3.448,7.896 3.813,8.094 0.365,0.198 10 false MB 0.396,2.531 0.76,2.688 0.365,0.156 10 false 3E*B 0.396,2.688 0.813,2.833 0.417,0.146 10 false 3F*C 5.031,5.208 5.24,5.344 0.208,0.135 10 false 3C 0.906,1.354 1.104,1.49 0.198,0.135 10 false 3D 0.146,0.094 0.344,0.229 0.198,0.135 10 false *A 5.042,3.833 5.24,3.99 0.198,0.156 10 false *B 5.615,3.833 5.813,4.01 0.198,0.177 10 false *C 1.823,5.198 2.021,5.333 0.198,0.135 10 false 3D 5.875,1.313 6.073,1.448 0.198,0.135 10 false 3B 1.823,6.563 2.021,6.698 0.198,0.135 10 false 3B 5.875,2 6.063,2.135 0.188,0.135 10 false 3A 5.083,6.563 5.271,6.698 0.188,0.135 10 false 3A 0.906,1.99 1.115,2.125 0.208,0.135 10 false 3C 1.938,1.323 2.302,1.542 0.365,0.219 10 false G59 1.833,0.344 2.125,0.479 0.292,0.135 10 false *1 5.333,3.865 5.563,4 0.229,0.135 10 false 3F 1.719,3.865 2.01,4 0.292,0.135 10 false G59 4.76,3.865 5.021,4 0.26,0.135 10 false 3E

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

U183433E02
1.635,0.958 1.635,0.615 1.635,0.615 1.771,0.615 false 4.094,1.146 4.094,0.635 4.094,0.635 4.229,0.635 false 1.677,1.531 1.948,1.531 false 1.677,1.958 1.948,1.958 false 0.771,2.719 1.042,2.719 false 2.219,3.792 2.5,3.948 0.281,0.156 10 false G60 4.698,3.802 4.979,3.958 0.281,0.156 10 false G59 1.156,5.063 1.438,5.219 0.281,0.156 10 false 3D 3.927,5.042 4.208,5.198 0.281,0.156 10 false 3C 1.813,6.313 2.094,6.469 0.281,0.156 10 false 3B 3.469,7.563 3.75,7.719 0.281,0.156 10 false MB 4.927,6.302 5.208,6.458 0.281,0.156 10 false 3A 5.896,5.052 6.177,5.208 0.281,0.156 10 false 3F 0.146,0.083 0.427,0.24 0.281,0.156 10 false *A 1.813,0.531 2.094,0.688 0.281,0.156 10 false *1 1.969,1.469 2.26,1.625 0.292,0.156 10 false G59 1.969,1.885 2.26,2.042 0.292,0.156 10 false G60 4.271,0.563 4.563,0.76 0.292,0.198 10 false MB 5.875,1.417 6.156,1.573 0.281,0.156 10 false 3B 5.875,2.094 6.156,2.25 0.281,0.156 10 false 3A 0.906,1.417 1.188,1.573 0.281,0.156 10 false 3D 0.906,2.094 1.188,2.25 0.281,0.156 10 false 3C 0.552,2.656 0.771,2.813 0.219,0.156 10 false 3F

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
MB-30 (BECU) - Body ground Input - Auxiliary battery power supply (for CPU) Always 11 to 14 V -
MB-29 (ACC) - Body ground Input - ACC power supply Power switch on (ACC) 11 to 14 V ACC SW
MB-32 (IG) - Body ground Input - Power switch power supply Power switch on (IG) 11 to 14 V IG SW

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
3D-36 (FLCY) - Body ground Input R - Body ground Front door LH courtesy light switch input Front door LH open Below 1 V FL Door Courtesy
Front door LH closed 11 to 14 V
G59-19 (FRCY) - Body ground Input R - Body ground Front door RH courtesy light switch input Front door RH open Below 1 V FR Door Courtesy
Front door RH closed 11 to 14 V
G59-24 (LCTY) - Body ground*1
G59-1 (LCTY) - Body ground*2
Input L - Body ground Rear door LH courtesy light switch input Rear door LH open Below 1 V RL Door Courtesy SW
Rear door LH closed Pulse generation (See waveform 3 or 4)
G59-6 (RCTY) - Body ground Input G - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V RR Door Courtesy SW
Rear door RH closed Pulse generation (See waveform 1 or 2)
3D-35 (BCTY) - Body ground Input B - Body ground Back door courtesy light switch input Back door open Below 1 V Back Door Courtesy SW
Power switch off, all doors closed and back door closed 11 to 14 V
G59-11 (L2) - Body ground Input SB - Body ground*3
B - Body ground*4
Driver door key-linked lock input Driver door key cylinder in lock position Below 1 V Door Key SW-Lock
Power switch off, all doors closed and driver door key cylinder in neutral position Pulse generation (See waveform 3 or 4)
G59-12 (UL2) - Body ground*1 Input LG - Body ground*3
G - Body ground*4
Driver door key-linked unlock input Driver door key cylinder in unlock position Below 1 V D Door Key SW-UL
Power switch off, all doors closed and driver door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
G59-24 (UL3) - Body ground*2 Input G - Body ground Driver door key-linked unlock input Driver door key cylinder in unlock position Below 1 V D Door Key SW-UL
Power switch off, all doors closed and driver door key cylinder in neutral position Pulse generation (See waveform 1 or 2)
3D-11 (ACT+) - Body ground Output GR - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3B-2 (ACT+) - Body ground Output V - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3B-1 (ACT+) - Body ground Output Y - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3D-12 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
3D-9 (TR+) - Body ground Output Y - Body ground Driver door lock motor unlock drive output Back door closed Below 1 V -
Back door open 11 to 14 V
3D-8 (ACT-) - Body ground Output P - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
3D-7 (ACT-) - Body ground Output LG - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
3B-4 (ACT-) - Body ground Output L - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
3B-3 (ACT-) - Body ground Output R - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
G59-7 (LSFL) - Body ground Input L - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V FL Door Lock Pos
Power switch off, all doors closed and front door LH locked Pulse generation (See waveform 1 or 2)
G59-18 (LSFR) - Body ground Input L - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V FR Door Lock Pos
Power switch off, all doors closed and front door RH locked Pulse generation (See waveform 1 or 2)
3D-24 (LSR) - Body ground Input Y - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V RL-Door Lock Pos SW
Power switch off, all doors closed and rear door LH and RH locked Pulse generation (See waveform 3 or 4)
3D-25 (LSR) - Body ground Input V - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V RR-Door Lock Pos SW
Power switch off, all doors closed and rear door RH and LH locked Pulse generation (See waveform 3 or 4)

*1: except Korea

*2: for Korea

*3: for LHD

*4: for RHD


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection G59-6 (RCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door RH closed

Waveform 1 (Reference)
Item Content
Tester Connection G59-12 (UL2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and driver door key cylinder in neutral position

Waveform 1 (Reference)
Item Content
Tester Connection G59-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door LH locked

Waveform 1 (Reference)
Item Content
Tester Connection G59-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door RH locked


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection G59-6 (RCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door RH closed

Waveform 2 (Reference)
Item Content
Tester Connection G59-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door LH locked

Waveform 2 (Reference)
Item Content
Tester Connection G59-12 (UL2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and driver door key cylinder in neutral position

Waveform 2 (Reference)
Item Content
Tester Connection G59-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door RH locked


g.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection G59-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and driver door key cylinder in neutral position

Waveform 3 (Reference)
Item Content
Tester Connection G59-24 (LCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door LH closed

Waveform 3 (Reference)
Item Content
Tester Connection 3D-24 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door LH and RH locked

Waveform 3 (Reference)
Item Content
Tester Connection 3D-25 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door RH and LH locked


h.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection G59-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and driver door key cylinder in neutral position

Waveform 4 (Reference)
Item Content
Tester Connection G59-24 (LCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Rear door LH closed

Waveform 4 (Reference)
Item Content
Tester Connection 3D-24 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door LH and RH locked

Waveform 4 (Reference)
Item Content
Tester Connection 3D-25 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door RH and LH locked