Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/ Occupant Classification System) › from 2017.06
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0320196 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) G

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the power switch on (IG).


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


c.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


d.

Start the hybrid control system.


e.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


f.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 2.INSPECT FRONT PASSENGER SEAT BELT WARNING LIGHT

HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the power switch on (IG).


b.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



c.

Fasten the driver seat belt.


d.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


e.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


f.

Start the hybrid control system.


g.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


h.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.


Hide 3.INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)>CUSTOMIZE PARAMETERS).


a.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


b.

Start the hybrid control system.


c.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



d.

When the vehicle is driven at approximately 20 km/h (12 mph) or more while the driver or front passenger seat belt is unfastened, check that the buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds. After that, the buzzer sounds at an interval of 0.4 seconds for 90 seconds. After that, check that the buzzer stops.


e.

Check that the buzzer stops 2 minutes after the buzzer starts sounding.


f.

After the buzzer has stopped, turn the power switch off and then start the hybrid control system again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver or front passenger seat belt is unfastened, and then check that the buzzer sounds again.


g.

After the buzzer has stopped, fasten the driver and front passenger seat belts. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver or front passenger seat belt, and then check that the buzzer sounds again.


h.

After the buzzer has stopped, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and then check that the buzzer sounds again.