Home › Engine / Hybrid System › 1NZ-FXE EMISSION CONTROL › EMISSION CONTROL SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057007 1NZ-FXE EMISSION CONTROL _0320443 EMISSION CONTROL SYSTEM(w/ Canister Pump Module) G

1NZ-FXE EMISSION CONTROL  EMISSION CONTROL SYSTEM(w/ Canister Pump Module)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

a.

Inspect the hoses and gaskets for scratches, cracks or air/oil leaks from the connecting parts.

HINT:

If the hoses or gaskets are damaged or some of the connections are loose, they may cause an engine stall or malfunction.



Hide 2.INSPECT EVAPORATIVE EMISSION CONTROL SYSTEM

a.

Connect the GTS to the DLC3.


b.
A276443

Disconnect the fuel vapor feed hose from the purge valve (purge VSV) as shown in the illustration.


c.

Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

Check that vacuum occurs at the purge valve (purge VSV) port.


g.

If vacuum does not occur, check the following items.

HINT:
·

Purge valve (purge VSV)

·

Clogging in the fuel vapor feed hose connecting the intake manifold and purge valve (purge VSV)




h.

Exit Active Test mode and connect the fuel vapor feed hose.


i.

Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP Purge VSV.


j.

Warm up the engine and drive the vehicle.


k.

Confirm that the purge valve (purge VSV) opens.

If the result is not as specified, replace the purge valve (purge VSV), wire harness or ECM.


Hide 3.CHECK FUEL TANK AND VENT LINE

a.

Disconnect the vent line tube from the canister (charcoal canister assembly).


b.

Connect a pressure gauge to the vent line tube.

A267669C01
0.75,0.417 1.146,0.417 1.146,0.417 1.396,0.74 false 2.073,2.427 2.25,2.427 2.25,2.427 2.802,1.458 false 6.479,0.771 6.135,0.771 6.135,0.771 6,1.375 false 0.583,0.344 0.75,0.51 0.167,0.167 10 false *1 6.5,0.677 6.677,0.854 0.177,0.177 10 false *3 1.896,2.344 2.063,2.51 0.167,0.167 10 false *2
*1 Fuel Tank Cap Assembly *2 Vent Line Tube
*3 Pressure Gauge - -



c.

Apply 4 kPa (0.04 kgf/cm2, 0.6 psi) of pressure to the vent line of the fuel tank assembly.

HINT:

Perform this inspection with the fuel tank assembly less than 90% full. When the fuel tank assembly is full, the fuel fill check valve closes and the pressure is released through the 2 mm(0.0787 in.) orifice. As a result, when the fuel tank cap assembly is removed, the pressure does not decrease smoothly.



d.

Check that the fuel tank pressure is maintained for some time, and does not decrease immediately.

HINT:

If the pressure decreases immediately, one of the following may apply:

·

The fuel tank cap assembly is not completely tightened.

·

The fuel tank cap assembly is damaged.

·

Air is leaking from the vent line.

·

The fuel tank assembly is damaged.




e.

Remove the fuel tank cap assembly and check that the pressure is released smoothly.

If the pressure is not released smoothly, replace the fuel tank assembly.


f.

Connect the vent line tube to the canister (charcoal canister assembly).


Hide 4.INSPECT AIR LINE

a.
A267668C01
1.677,0.104 1.854,0.26 0.177,0.156 10 false *a
*1 Air


Disconnect the air line tube from the leak detection pump sub-assembly.


b.

Check that air flows freely into the air line.

If air does not flow freely into the air line, repair or replace the air line tube.


c.

Connect the air line tube to the leak detection pump sub-assembly.