Home › Engine / Hybrid System › 1NZ-FXE EMISSION CONTROL › CANISTER(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057007 1NZ-FXE EMISSION CONTROL _0320446 CANISTER(w/ Canister Pump Module) A

1NZ-FXE EMISSION CONTROL  CANISTER(w/ Canister Pump Module)  REMOVAL  


PROCEDURE

Hide 77740 1.REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)

a.
U159058C01
1.927,2.729 2.208,2.729 false 0.729,1.729 0.927,1.729 0.927,1.729 1.073,1.49 true 0.833,2.49 1.01,2.49 1.01,2.49 1.26,2.208 true 2.25,2.646 2.469,2.865 0.219,0.219 10 false *a 0.573,1.646 0.74,1.813 0.167,0.167 10 false *1 0.677,2.406 0.896,2.625 0.219,0.219 10 false *b
*1 Air Line Tube
*a Retainer
*b Tab


Disconnect the leak detection pump sub-assembly connector.


b.

Disconnect the air line tube.

i.

Pull the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the air line tube.

NOTICE:
A275787C01
1.271,0.24 1.479,0.24 1.479,0.24 1.635,0.573 false 1.906,1.479 1.906,1.813 true 2.521,1.698 2.521,1.938 false 2.75,0.271 2.833,0.271 2.833,0.271 3,0.667 false 2.583,0.208 2.75,0.375 0.167,0.167 10 false *1 1.833,1.823 2,1.99 0.167,0.167 10 false *c 2.448,1.958 2.667,2.146 0.219,0.188 10 false *a 1.094,0.167 1.365,0.385 0.271,0.219 10 false *b
*1 Pipe (Leak Detection Pump Sub-Assembly)
*a Retainer
*b Tube Connector
*c O-ring


·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (leak detection pump sub-assembly).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the air line tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

·

If the tube connector and pipe (leak detection pump sub-assembly) are stuck, push and pull on them to release.



HINT:

Do not remove the retainer.




c.
A267666

Slide the clip and disconnect the purge line hose from the canister (charcoal canister assembly).


d.
U159107C01
0.969,2.385 1.219,2.385 1.219,2.385 1.427,2.188 false 0.719,1.188 1.156,1.188 true 1.99,2.688 2.281,2.688 false 0.813,2.292 1.031,2.5 0.219,0.208 10 false *b 0.563,1.115 0.771,1.302 0.208,0.188 10 true *1 2.323,2.615 2.542,2.823 0.219,0.208 10 false *a
*1 Vent Line Tube
*a Retainer
*b Tab
V100135

Pinch
V100136

Pull


Disconnect the vent line tube.

i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the vent line tube.

NOTICE:
A275787C01
1.271,0.24 1.479,0.24 1.479,0.24 1.635,0.573 false 1.906,1.479 1.906,1.813 true 2.521,1.698 2.521,1.938 false 2.75,0.271 2.833,0.271 2.833,0.271 3,0.667 false 2.583,0.208 2.75,0.375 0.167,0.167 10 false *1 1.833,1.823 2,1.99 0.167,0.167 10 false *c 2.448,1.958 2.667,2.146 0.219,0.188 10 false *a 1.094,0.167 1.365,0.385 0.271,0.219 10 false *b
*1 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer
*b Tube Connector
*c O-ring


·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the air line tube.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull on them to release.



HINT:

Do not remove the retainer.




e.
A267665

Remove the 3 bolts and canister (charcoal canister assembly).


Hide 77751 2.REMOVE CHARCOAL CANISTER BASE BRACKET

a.
A267662

Disengage the clamp and disconnect the vent hose.


b.

Remove the 4 bolts and charcoal canister base bracket.


Hide 77752 3.REMOVE CHARCOAL CANISTER SUPPORT BRACKET

a.
A267663

Disengage the clamp and disconnect the vent hose.


b.

Remove the 2 bolts and charcoal canister support bracket.


Hide 77765 4.REMOVE CHARCOAL CANISTER PROTECTOR

a.
A276441

Remove the clip and charcoal canister protector.


Hide 77745 5.REMOVE NO. 1 CHARCOAL CANISTER FILTER

a.
U159106C01
1.448,2.167 1.229,2.396 1.229,2.396 1.063,2.396 false 1.521,1.094 1.76,0.583 1.76,0.583 2.052,0.583 true 1.99,2.646 2.313,2.646 false 2.333,2.552 2.563,2.76 0.229,0.208 10 false *a 0.896,2.302 1.104,2.531 0.208,0.229 10 false *b 2.083,0.51 2.281,0.688 0.198,0.177 10 false *1
*1 Vent Hose
*a Retainer
*b Tab
V100135

Pinch
V100136

Pull


Disconnect the vent hose.

i.

Pinch the tabs of the retainer to disengage the lock claws and pull it down.


ii.

Pull off the vent hose and remove the No. 1 charcoal canister filter.

NOTICE:
A275787C01
1.271,0.24 1.479,0.24 1.479,0.24 1.635,0.573 false 1.906,1.479 1.906,1.813 true 2.521,1.698 2.521,1.938 false 2.75,0.271 2.833,0.271 2.833,0.271 3,0.667 false 2.583,0.208 2.75,0.375 0.167,0.167 10 false *1 1.833,1.823 2,1.99 0.167,0.167 10 false *c 2.448,1.958 2.667,2.146 0.219,0.188 10 false *a 1.094,0.167 1.365,0.385 0.271,0.219 10 false *b
*1 Pipe (Canister (Charcoal Canister Assembly))
*a Retainer
*b Tube Connector
*c O-ring


·

Remove any dirt or foreign matter on the tube connector before performing this work.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the vent hose.

·

Protect the disconnected parts by covering them with plastic bags after disconnecting the vent hose.

·

If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull on them to release.





Hide 77740R 6.REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY

HINT:

Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


a.

Before removing the leak detection pump sub-assembly, clean the No. 1 charcoal canister filter by blowing air into it to ensure that the No. 1 charcoal canister filter is free of foreign matter.

NOTICE:
·

Make sure to clean the No. 1 charcoal canister filter using air only.

·

Do not use gasoline, thinners or solvents.




b.
A267657C01
1.292,1.677 1.292,1.938 true 1.24,1.948 1.563,2.146 0.323,0.198 10 false *a
*a Protective Tape


While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.


c.

Check if the No. 1 charcoal canister filter contains foreign matter such as mud or water.

i.
A259514

Visually check that the inside of the No. 1 charcoal canister filter is free of foreign matter.


ii.

Hold the No. 1 charcoal canister filter upside down to make sure that it is free of foreign matter.

If the canister contains foreign matter, replace it.