Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL TANK(w/o Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0320558 FUEL TANK(w/o Canister Pump Module) A

1NZ-FXE FUEL  FUEL TANK(w/o Canister Pump Module)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

a.
A339034C02
2.333,1.635 2.531,1.854 2.531,1.854 2.677,1.854 false 2.729,1.781 3.042,1.938 0.313,0.156 10 false *a
*a Rope


When removing and installing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using rope or similar.

NOTICE:

Depending on the arrangement of the inlet hose during removal, the inlet hose and rear suspension may interfere and cause fuel leaks.



Hide 77020A 2.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 3.DRAIN FUEL

Hide 77310A 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 58156 5.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR

a.
A267873

Remove the 2 nuts and front No. 4 floor heat insulator.


Hide 77606 6.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A267874

Remove the clip.


b.

Remove the bolt and No. 1 fuel tank protector sub-assembly.


Hide 77262 7.DISCONNECT NO. 2 FUEL EMISSION TUBE

a.
A267876

Slide the clip and disconnect the No. 2 fuel emission tube.

NOTICE:
·

Remove any foreign matter on the clip and fuel pipe before performing this work.

·

Cover the disconnected fuel pipe and No. 2 fuel emission tube with plastic bags to prevent damage and contamination.




Hide 77266A 8.REMOVE NO. 1 FUEL TUBE PROTECTOR

a.
A268480C02
0.777,0.166 0.981,0.370 0.205,0.205 10 *1 1.63,0.756 1.125,0.251 1.125,0.251 0.981,0.251 false
*1 No. 1 Fuel Tube Protector


Remove the No. 1 fuel tube protector from the fuel tube connector.


Hide 77209F 9.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Pull the tabs of the retainer to disengage the lock claws and pull out the fuel tank main tube sub-assembly.

A309801C02
2.135,2.365 2.135,1.813 false 3.25,1.792 3.365,1.792 3.365,1.792 3.417,1.479 false 4.573,1.271 5,1.271 false 5.667,1.26 5.802,1.26 5.802,1.26 5.854,1.531 false 5.969,1.604 6.219,1.208 6.219,1.208 6.354,1.208 false 6.313,2.156 6.188,2.156 6.188,2.156 6.031,1.854 false 5.531,2.229 5.531,1.906 false 5.313,2.229 5.646,2.229 5.646,2.229 5.646,1.906 false 1.042,0.375 1.177,0.375 1.177,0.375 1.49,0.896 true 2.052,2.406 2.365,2.563 0.313,0.156 10 false *2 3.073,1.729 3.385,1.885 0.313,0.156 10 false *a 4.406,1.188 4.719,1.344 0.313,0.156 10 false *b 5.115,2.146 5.427,2.302 0.313,0.156 10 false *c 5.5,1.188 5.813,1.344 0.313,0.156 10 false *d 6.365,2.083 6.677,2.24 0.313,0.156 10 false *e 6.417,1.135 6.729,1.292 0.313,0.156 10 false *a 0.875,0.302 1.188,0.458 0.313,0.156 10 false *1
*1 Fuel Tank Main Tube Sub-assembly *2 Fuel Tank Pipe Setting Holder
*a Retainer *b Nylon Tube
*c O-ring *d Fuel Tube Connector
*e Fuel Pipe - -


NOTICE:
·

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube connector by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.

·

If the fuel tube connector and fuel pipe are stuck, push and pull to release them.




b.

Disengage the 3 clamps and remove the fuel tank pipe setting holder.


Hide 77100 10.REMOVE FUEL TANK ASSEMBLY

a.
A267877C03
1.906,1.625 2.208,1.625 false 1.365,1.719 1.125,2.208 1.125,2.208 1.063,2.208 false 1.729,1.698 1.729,1.906 false 2.354,0.865 2.729,0.865 false 0.906,2.146 1.188,2.344 0.281,0.198 10 false *a 2.25,1.542 2.417,1.729 0.167,0.188 10 false *1 2.792,0.792 3.063,1 0.271,0.208 10 false *1
*1 Fuel Tank Filler Pipe Flange Plate
*a Air Tube


Disengage the 2 clamps and separate the air tube.


b.

Remove the bolt.


c.

Disengage the claw and remove the fuel tank filler pipe flange plate.


d.
A267879

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



e.
A267878

Disengage the 2 clamps and separate the 2 fuel hoses.


f.
A267880

Remove the 4 bolts and fuel tank assembly.

NOTICE:
·

Slowly operate the engine lifter to lower the fuel tank.

·

Be careful not to drop the fuel tank assembly.




Hide 77701W 11.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A339050

Disengage the clamp to remove the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.


Hide 77281G 12.REMOVE FUEL HOSE CLAMP

a.
A267882

Remove the fuel hose clamp from the fuel tank assembly.


Hide 77209F 13.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A339051

Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77262 14.REMOVE NO. 2 FUEL EMISSION TUBE

a.
A339052

Disengage the 2 clamps to remove the No. 2 fuel emission tube from the fuel tank assembly.


Hide 77216A 15.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A267885

Remove the No. 1 fuel tank filler pipe support.


Hide 77217C 16.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A339057

Disengage the claw and remove the No. 2 fuel tank filler pipe support.