Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278073 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive radio waves relating to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly by identifying a key code based on the radio waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. DTC Detection Condition Trouble Area
B1242
·

Short in RDAS*1 or RDAM*2 to ground between the certification ECU (smart key ECU assembly) and the door control receiver.

·

Short in RSSI to ground between the certification ECU (smart key ECU assembly) and the door control receiver.*1

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO.*2


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (Smart key ECU assembly)



*1: for 5 Pin Type

*2: for 12 Pin Type


WIRING DIAGRAM

For 5 Pin Type


B281122E56
0.438,4.177 2.771,4.667 2.333,0.49 10 false Door Control Receiver Assembly 5.5,4.01 7.042,4.365 1.542,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.24,1.094 1.781,1.469 0.542,0.375 10 false RSSI 1.208,1.865 1.823,2.208 0.615,0.344 10 false DATA 1.396,2.688 1.792,2.969 0.396,0.281 10 false +5 5.802,1.094 6.542,1.49 0.74,0.396 10 false RSSI 5.813,1.885 6.573,2.292 0.76,0.406 10 false RDAS 5.813,2.677 6.833,3.125 1.021,0.448 10 false RCO 1.708,0.979 2.25,1.385 0.542,0.406 10 false 2 1.708,1.771 2.115,2.094 0.406,0.323 10 false 5 1.698,2.583 2.146,2.938 0.448,0.354 10 false 4 5.469,3.313 6.063,3.698 0.594,0.385 10 false 11 5.5,2.479 6.021,2.781 0.521,0.302 10 false 5 5.479,1.677 5.969,2.01 0.49,0.333 10 false 17 5.823,3.521 6.219,3.792 0.396,0.271 10 false E 5.469,0.896 5.802,1.219 0.333,0.323 10 false 19 1.292,3.5 1.917,3.875 0.625,0.375 10 false GND 1.688,3.396 2.083,3.688 0.396,0.292 10 false 1 0.438,4.021 1.021,4.302 0.583,0.281 10 false M15 5.438,3.5 5.885,3.792 0.448,0.292 10 false G77 5.427,2.667 5.792,2.927 0.365,0.26 10 false G78 5.438,1.875 5.896,2.188 0.458,0.313 10 false G78 5.427,1.083 5.802,1.417 0.375,0.333 10 false G78


For 12 Pin Type


B479757E02
1.156,0.844 1.771,1.042 0.615,0.198 10 false DATA 1.365,1.646 1.979,1.844 0.615,0.198 10 false +5 1.229,2.344 1.844,2.542 0.615,0.198 10 false GND 0.323,2.833 0.938,3.031 0.615,0.198 10 false M48 0.333,2.99 2.896,3.448 2.563,0.458 10 false Door Control and Tire Pressure Monitoring System Receiver Assembly 5.729,0.844 6.344,1.042 0.615,0.198 10 false RDAM 5.729,1.635 6.344,1.833 0.615,0.198 10 false RCO 5.729,2.333 6.344,2.531 0.615,0.198 10 false E 5.448,2.865 6.958,3.375 1.51,0.51 10 false Certification ECU (Smart Key ECU Assembly) 5.375,0.854 5.99,1.052 0.615,0.198 10 false G78 5.365,1.646 5.979,1.844 0.615,0.198 10 false G78 5.365,2.333 5.979,2.531 0.615,0.198 10 false G77 1.635,0.76 2.25,0.958 0.615,0.198 10 false 9 1.615,1.552 2.229,1.75 0.615,0.198 10 false 10 1.615,2.25 2.229,2.448 0.615,0.198 10 false 12 5.385,0.646 6,0.844 0.615,0.198 10 false 17 5.438,1.448 6.052,1.646 0.615,0.198 10 false 5 5.385,2.125 6,2.323 0.615,0.198 10 false 11


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, smart and wireless function performance may be affected.

·

Before performing the inspection, check that there are no problems related to the CAN communication system (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.* (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION)

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the door control receiver if the door control receiver has been replaced.*

*: w/ Tire Pressure Monitoring System


·

This DTC is not detected within 10 seconds after the power switch is turned to off from on (IG).



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the M15*1 or M48*2 door control receiver connector.

*1: for 5 Pin Type

*2: for 12 Pin Type



b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B440798C35
1.813,0.75 2.229,1 0.417,0.25 3.208,0.75 3.625,1 0.417,0.25 4.75,0.75 5.167,1 0.417,0.25 2.5,1.667 2.667,2.417 2.667,2.417 2.917,2.417 false 4.052,1.667 3.969,2.219 3.969,2.219 4.104,2.219 false 4.052,1.5 4.167,0.583 4.167,0.583 4.417,0.583 false 3.875,1.688 3.688,2.646 3.688,2.646 3.844,2.646 false 0.333,0.271 0.646,0.427 0.313,0.156 10 false *a 3.01,2.333 3.167,2.49 0.156,0.156 10 false E 4.146,2.125 4.76,2.354 0.615,0.229 10 false RDAS*A 4.5,0.49 5.031,0.75 0.531,0.26 10 false RCO 1.896,0.792 2.24,1.083 0.344,0.292 10 false G77 3.292,0.792 3.635,1.083 0.344,0.292 10 false G78 4.844,0.792 5.188,1.083 0.344,0.292 10 false G79 3.906,2.563 4.49,2.771 0.583,0.208 10 false RSSI 4.146,2.302 4.833,2.49 0.688,0.188 10 false RDAM*B
*A for 5 Pin Type *B for 12 Pin Type
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
G77-11 (E) - Body ground Always Below 1 Ω


Standard Voltage:
for 5 Pin Type
Tester Connection Condition Specified Condition
G78-5 (RCO) - G77-11 (E) Always Below 1 V → 4.5 to 5.5 V
(Pulse generation)
G78-19 (RSSI) - G77-11 (E) Always 11 to 14 V
G78-17 (RDAS) - G77-11 (E) Always 11 to 14 V

for 12 Pin Type
Tester Connection Condition Specified Condition
G78-5 (RCO) - G77-11 (E) Always Below 1 V → 4.5 to 5.5 V
(Pulse generation)
G78-17 (RDAM) - G77-11 (E) Always 11 to 14 V



Result:
Result Proceed to
NG A
OK (for 5 Pin Type) B
OK (for 12 Pin Type) C



A

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

REPLACE DOOR CONTROL RECEIVER

C

REPLACE DOOR CONTROL AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the G78 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Pin Type
Tester Connection Condition Specified Condition
G78-19 (RSSI) - M15-2 (RSSI) Always Below 1 Ω
G78-17 (RDAS) - M15-5 (DATA) Always Below 1 Ω
G78-5 (RCO) - M15-4 (+5) Always Below 1 Ω
M15-1 (GND) - Body ground Always Below 1 Ω
G78-19 (RSSI) or M15-2 (RSSI) - Body ground Always 10 kΩ or higher
G78-17 (RDAS) or M15-5 (DATA) - Body ground Always 10 kΩ or higher
G78-5 (RCO) or M15-4 (+5) - Body ground Always 10 kΩ or higher


Standard Resistance:
for 12 Pin Type
Tester Connection Condition Specified Condition
G78-17 (RDAM) - M48-9 (DATA) Always Below 1 Ω
G78-5 (RCO) - M48-10 (+5) Always Below 1 Ω
M48-12 (GND) - Body ground Always Below 1 Ω
G78-17 (RDAM) or M48-9 (DATA) - Body ground Always 10 kΩ or higher
G78-5 (RCO) or M48-10 (+5) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR