Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278101 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84307 1.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/o Occupant Classification System)

a.

Visually check for defects with the spiral cable with sensor sub-assembly removed from the vehicle.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable with sensor sub-assembly with a new one.



b.
B485242C01
1.729,0.208 2.063,0.438 0.333,0.229 2.365,0.208 2.698,0.438 0.333,0.229 0.469,1.042 0.802,1.271 0.333,0.229 1.99,3.521 2.323,3.75 0.333,0.229 1.052,3.323 1.375,3.542 0.323,0.219 1.823,0.24 2.208,0.51 0.385,0.271 10 false z2 2.458,0.24 2.844,0.51 0.385,0.271 10 false z6 0.573,1.073 0.958,1.344 0.385,0.271 10 false z3 1.125,3.354 1.365,3.531 0.24,0.177 10 true G5 2.031,3.552 2.417,3.823 0.385,0.271 10 false G19 0.104,0.073 0.49,0.344 0.385,0.271 10 false *a
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)


Check the spiral cable with sensor sub-assembly.

NOTICE:

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.


i.

Set the spiral cable with sensor sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Measure the resistance between each terminal of the spiral cable with sensor sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (CCS) - z6-3 Always 3 Ω or less
G5-2 (ECC) - z6-4 Always 3 Ω or less
G5-3 (EAU) - z2-7 Always 3 Ω or less
G5-4 (IL-2) - z2-8 Always 3 Ω or less
G5-5 (AU2) - z2-9 Always 3 Ω or less
G5-6 (AU1) - z2-10 Always 3 Ω or less
G5-8 (HO) - z2-1 Always 3 Ω or less
G5-9 (+DP) - z2-2 Always 3 Ω or less
G5-10 (+DP2) - z2-3 Always 3 Ω or less
G5-11 (TRIP) - z2-4 Always 3 Ω or less
G5-12 (IL+2) - z2-5 Always 3 Ω or less
G19-1 (D+) - z3-2 Always Below 1 Ω
G19-2 (D-) - z3-1 Always Below 1 Ω



iii.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable with sensor sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (CCS) - z6-3 Always 3 Ω or less
G5-2 (ECC) - z6-4 Always 3 Ω or less
G5-3 (EAU) - z2-7 Always 3 Ω or less
G5-4 (IL-2) - z2-8 Always 3 Ω or less
G5-5 (AU2) - z2-9 Always 3 Ω or less
G5-6 (AU1) - z2-10 Always 3 Ω or less
G5-8 (HO) - z2-1 Always 3 Ω or less
G5-9 (+DP) - z2-2 Always 3 Ω or less
G5-10 (+DP2) - z2-3 Always 3 Ω or less
G5-11 (TRIP) - z2-4 Always 3 Ω or less
G5-12 (IL+2) - z2-5 Always 3 Ω or less
G19-1 (D+) - z3-2 Always Below 1 Ω
G19-2 (D-) - z3-1 Always Below 1 Ω



iv.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (CCS) - z6-3 Always 3 Ω or less
G5-2 (ECC) - z6-4 Always 3 Ω or less
G5-3 (EAU) - z2-7 Always 3 Ω or less
G5-4 (IL-2) - z2-8 Always 3 Ω or less
G5-5 (AU2) - z2-9 Always 3 Ω or less
G5-6 (AU1) - z2-10 Always 3 Ω or less
G5-8 (HO) - z2-1 Always 3 Ω or less
G5-9 (+DP) - z2-2 Always 3 Ω or less
G5-10 (+DP2) - z2-3 Always 3 Ω or less
G5-11 (TRIP) - z2-4 Always 3 Ω or less
G5-12 (IL+2) - z2-5 Always 3 Ω or less
G19-1 (D+) - z3-2 Always Below 1 Ω
G19-2 (D-) - z3-1 Always Below 1 Ω


If the result is not as specified, replace the spiral cable with sensor sub-assembly.



Hide 84307 2.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ Occupant Classification System)

a.

Visually check for defects with the spiral cable with sensor sub-assembly removed from the vehicle.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable with sensor sub-assembly with a new one.



b.
C351641C02
0.885,3.469 1.281,3.677 0.396,0.208 1.708,0.177 2.083,0.427 0.375,0.25 2.302,0.177 2.719,0.427 0.417,0.25 0.708,1.083 1.083,1.333 0.375,0.25 0.25,1.083 0.625,1.333 0.375,0.25 1.958,3.656 2.354,3.865 0.396,0.208 0.302,1.885 0.583,1.885 false 0.938,1.885 1.219,1.885 false 0.115,0.125 0.531,0.396 0.417,0.271 10 false *a 1.823,0.208 2.24,0.479 0.417,0.271 10 false z2 2.438,0.208 2.854,0.479 0.417,0.271 10 false z6 0.365,1.125 0.781,1.396 0.417,0.271 10 false z3 0.792,1.125 1.208,1.396 0.417,0.271 10 false z10 0.146,1.802 0.563,2.073 0.417,0.271 10 false *b 1.25,1.802 1.667,2.073 0.417,0.271 10 false *c 0.99,3.49 1.406,3.76 0.417,0.271 10 false G5 2.031,3.677 2.448,3.948 0.417,0.271 10 false G19
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)
*b Color: Orange
*c Color: Black


Check the spiral cable with sensor sub-assembly.

NOTICE:

As the spiral cable with sensor sub-assembly may break, do not rotate the spiral cable with sensor sub-assembly more than the specified amount.


i.

Set the spiral cable with sensor sub-assembly to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).


ii.

Measure the resistance between each terminal of the spiral cable with sensor sub-assembly according to the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (CCS) - z6-3 Always 3 Ω or less
G5-2 (ECC) - z6-4 Always 3 Ω or less
G5-3 (EAU) - z2-7 Always 3 Ω or less
G5-4 (IL-2) - z2-8 Always 3 Ω or less
G5-5 (AU2) - z2-9 Always 3 Ω or less
G5-6 (AU1) - z2-10 Always 3 Ω or less
G5-8 (HO) - z2-1 Always 3 Ω or less
G5-9 (+DP) - z2-2 Always 3 Ω or less
G5-10 (+DP2) - z2-3 Always 3 Ω or less
G5-11 (TRIP) - z2-4 Always 3 Ω or less
G5-12 (IL+2) - z2-5 Always 3 Ω or less
G19-1 (D+) - z3-2 Always Below 1 Ω
G19-2 (D-) - z3-1 Always Below 1 Ω
G19-3 (D2-) - z10-1 Always Below 1 Ω
G19-4 (D2+) - z10-2 Always Below 1 Ω



iii.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise, and measure the resistance as shown in the table below. Then rotate the spiral cable with sensor sub-assembly 5 times counterclockwise, and measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (CCS) - z6-3 Always 3 Ω or less
G5-2 (ECC) - z6-4 Always 3 Ω or less
G5-3 (EAU) - z2-7 Always 3 Ω or less
G5-4 (IL-2) - z2-8 Always 3 Ω or less
G5-5 (AU2) - z2-9 Always 3 Ω or less
G5-6 (AU1) - z2-10 Always 3 Ω or less
G5-8 (HO) - z2-1 Always 3 Ω or less
G5-9 (+DP) - z2-2 Always 3 Ω or less
G5-10 (+DP2) - z2-3 Always 3 Ω or less
G5-11 (TRIP) - z2-4 Always 3 Ω or less
G5-12 (IL+2) - z2-5 Always 3 Ω or less
G19-1 (D+) - z3-2 Always Below 1 Ω
G19-2 (D-) - z3-1 Always Below 1 Ω
G19-3 (D2-) - z10-1 Always Below 1 Ω
G19-4 (D2+) - z10-2 Always Below 1 Ω



iv.

After setting the spiral cable with sensor sub-assembly to the center position, rotate the spiral cable with sensor sub-assembly 2.5 times clockwise. Then while rotating the spiral cable with sensor sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G5-1 (CCS) - z6-3 Always 3 Ω or less
G5-2 (ECC) - z6-4 Always 3 Ω or less
G5-3 (EAU) - z2-7 Always 3 Ω or less
G5-4 (IL-2) - z2-8 Always 3 Ω or less
G5-5 (AU2) - z2-9 Always 3 Ω or less
G5-6 (AU1) - z2-10 Always 3 Ω or less
G5-8 (HO) - z2-1 Always 3 Ω or less
G5-9 (+DP) - z2-2 Always 3 Ω or less
G5-10 (+DP2) - z2-3 Always 3 Ω or less
G5-11 (TRIP) - z2-4 Always 3 Ω or less
G5-12 (IL+2) - z2-5 Always 3 Ω or less
G19-1 (D+) - z3-2 Always Below 1 Ω
G19-2 (D-) - z3-1 Always Below 1 Ω
G19-3 (D2-) - z10-1 Always Below 1 Ω
G19-4 (D2+) - z10-2 Always Below 1 Ω


If the result is not as specified, replace the spiral cable with sensor sub-assembly.