The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.
These DTCs are stored when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1612/83
B1613/83 |
·
The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor RH circuit. ·
Front airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor RH ·
Airbag sensor assembly |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
OK
NG
Connect the connectors that link the engine room main wire and instrument panel wire.
| *A | w/o Occupant Classification System | *B | w/ Occupant Classification System |
| *1 | Front Airbag Sensor RH | *2 | Airbag Sensor Assembly |
| *3 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to Front Airbag Sensor RH) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-2 (+SR) - Body ground | Power switch on (IG) | Below 1 V |
| A23-1 (-SR) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-2 (+SR) - A23-1 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-2 (+SR) - A23-1 (-SR) | Always | 1 MΩ or higher |
| A23-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| A23-1 (-SR) - Body ground | Always | 1 MΩ or higher |
OK
NG
| *A | w/o Occupant Classification System |
| *B | w/ Occupant Classification System |
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the front airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. | A |
| DTC B1617/84 or B1618/84 is output. | B |
| DTC B1612/83 or B1613/83 is output. | C |
Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Return the front airbag sensor RH and LH to their original positions and connect the connectors.
A
(See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Disconnect the instrument panel wire connector from the engine room main wire.
| *A | w/o Occupant Classification System | *B | w/ Occupant Classification System |
| *1 | Front Airbag Sensor RH | *2 | Airbag Sensor Assembly |
| *3 | Engine Room Main Wire | *4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to Engine Room Main Wire) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AG5-1 (+SR) - Body ground | Power switch on (IG) | Below 1 V |
| AG5-2 (-SR) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AG5-1 (+SR) - AG5-2 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AG5-1 (+SR) - AG5-2 (-SR) | Always | 1 MΩ or higher |
| AG5-1 (+SR) - Body ground | Always | 1 MΩ or higher |
| AG5-2 (-SR) - Body ground | Always | 1 MΩ or higher |
OK
NG