Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1617/84
B1618/84
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the front airbag sensor LH circuit.

·

Front airbag sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

B483343E02
3.448,0.906 3.969,1.24 0.521,0.333 10 false AG5 3.448,2.073 3.969,2.406 0.521,0.333 10 false AG5 5.135,0.792 5.656,1.125 0.521,0.333 10 false 30 5.396,2.073 5.917,2.406 0.521,0.333 10 false -SL 5.396,0.906 5.917,1.24 0.521,0.333 10 false +SL 5.135,1.958 5.656,2.292 0.521,0.333 10 false 28 5.344,2.917 6.188,3.302 0.844,0.385 10 false G18 5.344,3.083 6.938,3.427 1.594,0.344 10 false Airbag Sensor Assembly 3.542,0.708 4.063,1.042 0.521,0.333 10 false 3 3.542,1.875 4.063,2.208 0.521,0.333 10 false 4 1.854,0.792 2.375,1.125 0.521,0.333 10 false 2 1.844,1.958 2.365,2.292 0.521,0.333 10 false 1 0.563,2.917 1.135,3.271 0.573,0.354 10 false A24 0.563,3.073 2.156,3.438 1.594,0.365 10 false Front Airbag Sensor LH 1.479,0.896 2,1.229 0.521,0.333 10 false +SL 1.5,2.073 2.021,2.406 0.521,0.333 10 false -SL

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH. Also check that the connectors that link the engine room main wire and instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH. Also disconnect the connectors that link the engine room main wire and instrument panel wire.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - FRONT AIRBAG SENSOR LH)

NG

REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - FRONT AIRBAG SENSOR LH)
a.

Connect the connectors that link the engine room main wire and instrument panel wire.

C284131C06
0.729,2.938 1.083,3.177 0.354,0.24 1.135,0.469 1.479,0.698 0.344,0.229 4.729,0.479 5.073,0.708 0.344,0.229 4.385,2.938 4.74,3.177 0.354,0.24 2.177,0.76 1.99,0.948 false 1.563,3.031 1.74,3.365 false 2.25,0.979 2.25,1.115 false 5.854,0.99 5.854,1.125 false 5.781,0.76 5.573,0.948 false 2.333,0.771 2.521,0.958 false 1.365,3.031 1.188,3.365 false 4.969,3.031 4.792,3.365 false 5.167,3.021 5.344,3.354 false 5.927,0.76 6.125,0.958 false 0.167,0.146 0.479,0.396 0.313,0.25 10 false *A 3.677,0.146 3.979,0.396 0.302,0.25 10 false *B 1.135,0.25 1.448,0.448 0.313,0.198 10 false *a 4.74,0.25 5.052,0.448 0.313,0.198 10 false *a 0.688,2.656 1,2.854 0.313,0.198 10 false *b 4.281,2.656 4.594,2.854 0.313,0.198 10 false *b 0.635,1.708 0.948,1.906 0.313,0.198 10 false *1 4.229,1.917 4.542,2.115 0.313,0.198 10 false *1 6.24,1.917 6.552,2.115 0.313,0.198 10 false *2 2.646,1.948 2.958,2.146 0.313,0.198 10 false *2 2.292,1.719 2.448,1.917 0.156,0.198 10 false A 2.042,1.719 2.198,1.917 0.156,0.198 10 false B 1.667,1.719 1.823,1.917 0.156,0.198 10 false C 1.177,1.719 1.333,1.917 0.156,0.198 10 false E 0.927,1.719 1.083,1.917 0.156,0.198 10 false F 5.896,1.927 6.052,2.125 0.156,0.198 10 false A 5.646,1.927 5.802,2.125 0.156,0.198 10 false B 5.271,1.927 5.427,2.125 0.156,0.198 10 false C 1.542,1.719 1.698,1.917 0.156,0.198 10 false D 5.146,1.927 5.302,2.125 0.156,0.198 10 false D 4.771,1.927 4.927,2.125 0.156,0.198 10 false E 4.521,1.927 4.677,2.125 0.156,0.198 10 false F 1.188,0.5 1.521,0.75 0.333,0.25 10 false G18 0.792,2.979 1.156,3.24 0.365,0.26 10 false A24 2.167,1.135 2.417,1.344 0.25,0.208 10 false *3 5.771,1.146 6,1.354 0.229,0.208 10 false *3 1.76,0.885 2.073,1.094 0.313,0.208 10 false -SL 2.552,0.885 3.01,1.083 0.458,0.198 10 false +SL 1.052,3.375 1.51,3.573 0.458,0.198 10 false -SL 1.594,3.375 2.052,3.573 0.458,0.198 10 false +SL 4.646,3.385 4.99,3.615 0.344,0.229 10 false -SL 5.208,3.385 5.583,3.615 0.375,0.229 10 false +SL 6.135,0.896 6.542,1.156 0.406,0.26 10 false +SL 5.344,0.896 5.656,1.125 0.313,0.229 10 false -SL 4.781,0.51 5.177,0.792 0.396,0.281 10 false G18 4.448,2.979 4.813,3.24 0.365,0.26 10 false A24
*A w/o Occupant Classification System *B w/ Occupant Classification System
*1 Front Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Airbag Sensor LH)



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 (+SL) - Body ground Power switch on (IG) Below 1 V
A24-1 (-SL) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (+SL) - A24-1 (-SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (+SL) - A24-1 (-SL) Always 1 MΩ or higher
A24-2 (+SL) - Body ground Always 1 MΩ or higher
A24-1 (-SL) - Body ground Always 1 MΩ or higher




OK

3.CHECK FRONT AIRBAG SENSOR LH

NG

4.CHECK INSTRUMENT PANEL WIRE
3.CHECK FRONT AIRBAG SENSOR LH
a.
C279500C02
0.156,0.073 0.552,0.375 0.396,0.302 10 false *A 0.198,2.365 0.573,2.688 0.375,0.323 10 false *B 0.49,0.938 0.833,1.208 0.344,0.271 10 false *1 2.625,3.479 2.948,3.792 0.323,0.313 10 false *2 2.604,1.24 2.948,1.51 0.344,0.271 10 false *2 2.177,0.958 2.521,1.229 0.344,0.271 10 false A 2.021,0.958 2.365,1.229 0.344,0.271 10 false B 1.573,0.958 1.917,1.229 0.344,0.271 10 false C 1.417,0.958 1.76,1.229 0.344,0.271 10 false D 0.969,0.958 1.313,1.229 0.344,0.271 10 false E 0.813,0.958 1.156,1.229 0.344,0.271 10 false F 2.177,3.458 2.521,3.729 0.344,0.271 10 false A 2.021,3.458 2.365,3.729 0.344,0.271 10 false B 1.573,3.458 1.917,3.729 0.344,0.271 10 false C 1.417,3.458 1.76,3.729 0.344,0.271 10 false D 0.969,3.458 1.313,3.729 0.344,0.271 10 false E 0.823,3.458 1.167,3.729 0.344,0.271 10 false F 0.49,3.458 0.833,3.729 0.344,0.271 10 false *1
*A w/o Occupant Classification System
*B w/ Occupant Classification System
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1612/83, B1613/83, B1617/84 and B1618/84 are not output. A
DTC B1617/84 or B1618/84 is output. B
DTC B1612/83 or B1613/83 is output. C


HINT:

Codes other than DTCs B1612/83, B1613/83, B1617/84 and B1618/84, may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Return the front airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

4.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the engine room main wire.

B485256C01
1.229,0.458 1.573,0.667 0.344,0.208 4.833,0.458 5.177,0.667 0.344,0.208 0.865,2.938 1.208,3.146 0.344,0.208 4.396,2.938 4.74,3.146 0.344,0.208 5.979,1.125 5.979,0.958 false 2.313,1.125 2.313,0.958 false 2,1.042 2.24,0.76 false 2.667,1.042 2.396,0.76 false 5.656,1.042 5.896,0.76 false 6.302,1.031 6.042,0.76 false 1.927,2.021 1.927,1.771 false 1.271,2.021 1.271,1.771 false 5.521,2.26 5.521,2.01 false 4.854,1.938 4.854,1.604 4.854,1.604 4.688,1.604 false 1.958,3.365 1.615,3.135 false 1.135,3.365 1.5,3.135 false 5.563,3.365 5.198,3.135 false 4.719,3.365 5.083,3.135 false 0.333,0.167 0.938,0.823 0.604,0.656 10 false *A 3.833,0.167 4.25,0.5 0.417,0.333 10 false *B 0.573,1.656 1.042,2.073 0.469,0.417 10 false *1 6.24,1.896 6.719,2.271 0.479,0.375 10 false *2 1.208,2.031 1.594,2.385 0.385,0.354 10 false *3 5.458,2.271 5.875,2.594 0.417,0.323 10 false *4 2.25,1.135 2.688,1.438 0.438,0.302 10 false *5 1.229,0.24 1.646,0.688 0.417,0.448 10 false *a 0.688,2.625 1.135,3.073 0.448,0.448 10 false *b 4.542,1.521 4.927,1.875 0.385,0.354 10 false *3 1.865,2.031 2.313,2.344 0.448,0.313 10 false *4 5.917,1.135 6.354,1.438 0.438,0.302 10 false *5 4.833,0.24 5.25,0.688 0.417,0.448 10 false *a 4.281,2.625 4.729,3.073 0.448,0.448 10 false *b 2.531,1.042 2.969,1.344 0.438,0.302 10 false +SL 1.865,1.042 2.302,1.344 0.438,0.302 10 false -SL 5.531,1.042 5.969,1.344 0.438,0.302 10 false -SL 0.906,2.958 1.344,3.26 0.438,0.302 10 false AG5 4.885,0.479 5.323,0.781 0.438,0.302 10 false G18 6.188,1.042 6.625,1.344 0.438,0.302 10 false +SL 2.354,1.667 2.833,2.042 0.479,0.375 10 false A 2.083,1.667 2.563,2.042 0.479,0.375 10 false B 1.688,1.667 2.167,2.042 0.479,0.375 10 false C 1.417,1.667 1.896,2.042 0.479,0.375 10 false D 1.021,1.667 1.5,2.042 0.479,0.375 10 false E 0.76,1.667 1.24,2.042 0.479,0.375 10 false F 5.938,1.906 6.417,2.281 0.479,0.375 10 false A 5.667,1.906 6.146,2.281 0.479,0.375 10 false B 5.271,1.906 5.75,2.281 0.479,0.375 10 false C 5,1.906 5.479,2.281 0.479,0.375 10 false D 4.604,1.906 5.083,2.281 0.479,0.375 10 false E 4.344,1.906 4.823,2.281 0.479,0.375 10 false F 4.135,1.906 4.604,2.323 0.469,0.417 10 false *1 2.646,1.896 3.125,2.271 0.479,0.375 10 false *2 4.438,2.958 4.875,3.26 0.438,0.302 10 false AG5 1.281,0.479 1.719,0.781 0.438,0.302 10 false G18 1.865,3.365 2.302,3.667 0.438,0.302 10 false +SL 0.99,3.365 1.427,3.667 0.438,0.302 10 false -SL 5.458,3.365 5.896,3.667 0.438,0.302 10 false +SL 4.583,3.365 5.021,3.667 0.438,0.302 10 false -SL
*A w/o Occupant Classification System *B w/ Occupant Classification System
*1 Front Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Service Wire - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Engine Room Main Wire)



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - Body ground Power switch on (IG) Below 1 V
AG5-4 (-SL) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - AG5-4 (-SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AG5-3 (+SL) - AG5-4 (-SL) Always 1 MΩ or higher
AG5-3 (+SL) - Body ground Always 1 MΩ or higher
AG5-4 (-SL) - Body ground Always 1 MΩ or higher




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE