Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1650/32  Occupant Classification System Malfunction  


DESCRIPTION

The occupant classification system circuit consists of the airbag sensor assembly and occupant classification system.

If the airbag sensor assembly receives signals from the occupant detection ECU, it determines whether the instrument panel passenger airbag assembly, front seat airbag sub-assembly RH and front seat outer belt assembly RH should be operated.

DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC No. DTC Detection Condition Trouble Area
B1650/32
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the occupant classification system circuit.

·

Occupant classification system malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat wire RH

·

Occupant classification system

·

Airbag sensor assembly



WIRING DIAGRAM

C238367E49
0.573,3.083 2.417,3.417 1.844,0.333 10 false Occupant Detection ECU 0.573,2.917 1.292,3.354 0.719,0.438 10 false O2 3.406,0.906 3.896,1.49 0.49,0.583 10 false MO1 3.51,0.698 3.948,1.396 0.438,0.698 10 false 1 3.51,1.885 4.021,2.667 0.51,0.781 10 false 5 3.406,2.083 3.875,2.542 0.469,0.458 10 false MO1 5.135,0.802 5.667,1.281 0.531,0.479 10 false 16 5.146,1.958 5.542,2.313 0.396,0.354 10 false 24 5.354,2.917 5.948,3.281 0.594,0.365 10 false M58 5.354,3.094 7.104,3.417 1.75,0.323 10 false Airbag Sensor Assembly 1.396,0.906 2.448,1.531 1.052,0.625 10 false FSR+ 1.427,2.073 2.115,2.385 0.688,0.313 10 false FSR- 5.385,0.917 5.969,1.354 0.583,0.438 10 false FSR+ 5.385,2.083 6.01,2.542 0.625,0.458 10 false FSR- 1.854,0.781 2.281,1.458 0.427,0.677 10 false 7 1.854,1.969 2.24,2.396 0.385,0.427 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC (OCCUPANT DETECTION ECU)
a.

Check for DTCs of the occupant detection ECU (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC is not output.




OK

2.CHECK CONNECTORS

NG

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU. Also check that the connectors that link the floor wire and front seat wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and occupant detection ECU. Also disconnect the connectors that link the floor wire and front seat wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - OCCUPANT DETECTION ECU)

NG

REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - OCCUPANT DETECTION ECU)
a.
C238377C08
0.677,3.781 1,4.01 0.323,0.229 0.333,0.604 0.698,0.854 0.365,0.25 1.948,0.844 2.198,0.844 false 1.646,0.729 1.99,0.479 false 1.646,0.948 1.99,1.167 false 1.531,3.958 1.531,4.365 false 1.74,3.792 1.74,3.375 1.74,3.375 2,3.375 false 1.406,2.406 1.792,2.76 0.385,0.354 10 false D 1.063,2.406 1.396,2.771 0.333,0.365 10 false E 0.823,2.406 1.25,2.74 0.427,0.333 10 false F 1.563,2.406 1.979,2.792 0.417,0.385 10 false C 1.906,2.406 2.208,2.823 0.302,0.417 10 false B 2.146,2.406 2.458,2.792 0.313,0.385 10 false A 0.427,2.563 0.781,2.875 0.354,0.313 10 false *1 2.635,2.104 2.948,2.406 0.313,0.302 10 false *2 2.021,0.396 2.458,0.635 0.438,0.24 10 false FSR+ 2.031,1.104 2.542,1.438 0.51,0.333 10 false FSR- 0.271,0.156 0.552,0.438 0.281,0.281 10 false *a 2.042,3.302 2.448,3.594 0.406,0.292 10 false FSR- 1.385,4.385 1.844,4.625 0.458,0.24 10 false FSR+ 0.76,3.813 1.104,4.073 0.344,0.26 10 false O2 0.385,0.646 0.813,1.042 0.427,0.396 10 false M58 0.583,3.281 0.958,3.583 0.375,0.302 10 false *b 2.229,0.76 2.479,1.021 0.25,0.26 10 false *3
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Occupant Detection ECU)


Connect the connectors that link the floor wire and front seat wire RH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - Body ground Power switch on (IG) Below 1 V
O2-4 (FSR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - O2-4 (FSR-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-7 (FSR+) - O2-4 (FSR-) Always 1 MΩ or higher
O2-7 (FSR+) - Body ground Always 1 MΩ or higher
O2-4 (FSR-) - Body ground Always 1 MΩ or higher




OK

NG

4.CHECK FLOOR WIRE
4.CHECK FLOOR WIRE
a.
C238379C07
0.583,3.781 0.958,4.01 0.375,0.229 0.313,0.604 0.656,0.844 0.344,0.24 1.948,0.833 2.24,0.833 false 1.615,0.708 1.958,0.51 false 1.625,0.948 1.969,1.146 false 1.365,3.979 1.365,4.323 false 1.375,3.844 1.375,3.385 1.375,3.385 1.51,3.385 false 1.281,2.583 1.281,2.833 false 1.813,2.448 1.813,2.115 1.813,2.115 1.594,2.115 false 1.396,2.438 1.833,2.823 0.438,0.385 10 false D 1.083,2.438 1.552,2.813 0.469,0.375 10 false E 0.844,2.438 1.083,2.74 0.24,0.302 10 false F 1.615,2.438 1.938,2.76 0.323,0.323 10 false C 1.927,2.438 2.24,2.854 0.313,0.417 10 false B 2.177,2.438 2.448,2.729 0.271,0.292 10 false A 0.448,2.573 1.042,3.031 0.594,0.458 10 false *1 2.656,2.135 3,2.594 0.344,0.458 10 false *2 2.01,0.417 2.49,0.667 0.479,0.25 10 false FSR+ 2.01,1.073 2.479,1.375 0.469,0.302 10 false FSR- 0.26,0.156 0.563,0.438 0.302,0.281 10 false *a 1.552,3.313 1.969,3.667 0.417,0.354 10 false FSR+ 0.635,3.813 1.063,4.146 0.427,0.333 10 false MO1 0.354,0.646 0.844,1.01 0.49,0.365 10 false M58 0.49,3.281 0.958,3.563 0.469,0.281 10 false *b 1.24,4.354 1.688,4.667 0.448,0.313 10 false FSR- 1.208,2.854 1.531,3.24 0.323,0.385 10 false *3 1.438,2.031 1.906,2.375 0.469,0.344 10 false *4 2.271,0.76 2.604,1.031 0.333,0.271 10 false *5
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Front Seat Wire RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Wire RH)


Disconnect the front seat wire RH from the floor wire.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - Body ground Power switch on (IG) Below 1 V
MO1-5 (FSR-) - Body ground Power switch on (IG) Below 1 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



g.

Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - MO1-5 (FSR-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MO1-1 (FSR+) - MO1-5 (FSR-) Always 1 MΩ or higher
MO1-1 (FSR+) - Body ground Always 1 MΩ or higher
MO1-5 (FSR-) - Body ground Always 1 MΩ or higher




OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE