Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1656/38  Seat Belt Buckle Switch LH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag sensor assembly and front seat inner belt assembly LH.

DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1656/38
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat belt buckle switch LH circuit.

·

Front seat inner belt assembly LH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH)

·

Airbag sensor assembly



WIRING DIAGRAM

C256967E03
1.656,0.781 2.594,1.26 0.938,0.479 10 false LBE+ 1.677,2.198 2.51,2.667 0.833,0.469 10 false LBE- 5.385,0.906 6.073,1.458 0.688,0.552 10 false LBE+ 5.385,2.073 5.948,2.375 0.563,0.302 10 false LBE- 2.125,0.792 2.625,1.458 0.5,0.667 10 false 2 2.115,1.948 2.667,2.354 0.552,0.406 10 false 1 5.135,0.802 5.656,1.25 0.521,0.448 10 false 10 5.135,1.958 5.667,2.427 0.531,0.469 10 false 18 0.552,2.917 1.469,3.281 0.917,0.365 10 false M51 0.552,3.094 2.74,3.573 2.188,0.479 10 false Front Seat Inner Belt Assembly LH (Seat Belt Buckle Switch LH) 5.323,2.917 5.813,3.302 0.49,0.385 10 false M57 5.323,3.083 6.958,3.469 1.635,0.385 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FLOOR WIRE

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE
a.
C265017C12
0.344,3.635 0.719,3.885 0.375,0.25 1.135,0.531 1.5,0.771 0.365,0.24 0.906,4.24 1.281,3.771 false 1.896,4.25 1.521,3.781 false 1.531,2.094 1.531,1.677 1.531,1.677 1.365,1.677 false 2.073,0.802 1.823,0.802 false 2,0.333 2.375,0.677 false 2,1.25 2.375,0.906 false 0.583,2.052 0.938,2.396 0.354,0.344 10 false *1 2.521,2.396 2.854,2.708 0.333,0.313 10 false *2 1.208,1.604 1.594,1.948 0.385,0.344 10 false *3 1.677,0.729 2.021,1.031 0.344,0.302 10 false *4 0.938,0.146 1.292,0.49 0.354,0.344 10 false *a 0.198,3.167 0.521,3.5 0.323,0.333 10 false *b 2.021,2.083 2.354,2.396 0.333,0.313 10 false A 1.729,2.083 2.063,2.396 0.333,0.313 10 false B 1.271,2.083 1.604,2.396 0.333,0.313 10 false C 0.969,2.083 1.302,2.396 0.333,0.313 10 false D 1.188,0.563 1.625,0.927 0.438,0.365 10 false M57 0.406,3.677 0.781,4 0.375,0.323 10 false M51 1.615,0.25 2.042,0.458 0.427,0.208 10 false LBE+ 1.625,1.188 2.052,1.396 0.427,0.208 10 false LBE- 1.771,4.25 2.302,4.5 0.531,0.25 10 false LBE+ 0.76,4.25 1.167,4.479 0.406,0.229 10 false LBE-
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M51-2 (LBE+) - Body ground Power switch on (IG) Below 1 V
M51-1 (LBE-) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-2 (LBE+) - M51-1 (LBE-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M51-2 (LBE+) - M51-1 (LBE-) Always 1 MΩ or higher
M51-2 (LBE+) - Body ground Always 1 MΩ or higher
M51-1 (LBE-) - Body ground Always 1 MΩ or higher




OK

3.CHECK DTC

NG

REPLACE FLOOR WIRE

3.CHECK DTC
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656/38 is not output.


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.




OK

NG

4.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
4.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
a.
C238328C01
0.719,0.813 1.073,1.24 0.354,0.427 10 false *1 1.104,0.813 1.354,1.25 0.25,0.438 10 false D 1.26,0.813 1.573,1.167 0.313,0.354 10 false C 1.729,0.813 2.031,1.073 0.302,0.26 10 false B 1.885,0.813 2.135,1.073 0.25,0.26 10 false A 2.323,1.135 2.646,1.385 0.323,0.25 10 false *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Replace the front seat inner belt assembly LH with a known good one (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656/38 is not output.


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the front seat inner belt assembly LH that was installed for testing to its original location (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG