Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057039 SUPPLEMENTAL RESTRAINT SYSTEMS _0278099 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660/43  Passenger Airbag ON/OFF Indicator Circuit Malfunction  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and combination meter assembly (passenger airbag ON/OFF indicator).

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag assembly, front seat airbag sub-assembly RH and front seat outer belt assembly RH.

DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. DTC Detection Condition Trouble Area
B1660/43
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit.

·

Combination meter assembly malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Combination meter assembly (Passenger airbag ON/OFF indicator)

·

Airbag sensor assembly



WIRING DIAGRAM

C239224E31
1.292,1.094 2,1.396 0.708,0.302 10 false PAON 1.354,2.094 2,2.438 0.646,0.344 10 false P-AB 1.448,3.094 1.979,3.458 0.531,0.365 10 false IG+ 1.771,2.969 2.052,3.365 0.281,0.396 10 false 21 1.781,1.979 2.25,2.344 0.469,0.365 10 false 4 1.781,0.979 2.135,1.375 0.354,0.396 10 false 3 5.479,1.094 6.021,1.5 0.542,0.406 10 false PAON 5.479,2.094 5.906,2.438 0.427,0.344 10 false P-AB 5.479,3.094 5.771,3.49 0.292,0.396 10 false E1 5.479,4.104 5.917,4.5 0.438,0.396 10 false E2 5.219,2.99 5.625,3.375 0.406,0.385 10 false 25 5.219,4 5.688,4.396 0.469,0.396 10 false 26 5.219,1.979 5.76,2.458 0.542,0.479 10 false 17 5.219,0.979 5.583,1.385 0.365,0.406 10 false 23 2.635,4.073 4.042,4.427 1.406,0.354 10 false from IG2 Relay 0.542,4.76 0.99,5.083 0.448,0.323 10 false G1 0.542,4.927 2.885,5.521 2.344,0.594 10 false Combination Meter Assembly (Passenger Airbag ON/OFF Indicator) 5.396,4.76 5.844,5.104 0.448,0.344 10 false G18 5.396,4.948 7,5.323 1.604,0.375 10 false Airbag Sensor Assembly 2.146,3.24 2.917,3.583 0.771,0.344 10 false METER

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the power switch on (IG).


b.

Check the passenger airbag ON/OFF indicator operation.

Result:
ON/OFF Indicator Illumination Proceed to
Always ON A
OFF B


HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).




A

2.CHECK CONNECTORS

B

6.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and combination meter assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.

Connect the connector to the combination meter assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Connect the connector to the airbag sensor assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
B483361C01
0.333,3.688 0.656,3.906 0.323,0.219 0.729,0.521 1.104,0.76 0.375,0.24 1.479,2.323 1.479,1.906 1.479,1.906 1.313,1.906 false 1.688,1.354 1.688,1.104 false 0.698,4.24 1.042,3.875 false 2.313,1.135 1.854,0.677 false 1.469,4.24 1.125,3.875 false 1.156,1.125 1.5,0.854 false 0.479,2.281 0.896,2.656 0.417,0.375 10 false *1 2.542,2.302 3.021,2.792 0.479,0.49 10 false *2 1.167,1.833 1.667,2.24 0.5,0.406 10 false *3 1.615,1.354 2.042,1.708 0.427,0.354 10 false *4 0.635,0.25 1.042,0.708 0.406,0.458 10 false *a 0.271,3.198 0.656,3.729 0.385,0.531 10 false *b 2.125,2.292 2.604,2.781 0.479,0.49 10 false A 1.74,2.292 2.219,2.781 0.479,0.49 10 false B 1.115,2.292 1.594,2.781 0.479,0.49 10 false C 0.729,2.292 1.208,2.781 0.479,0.49 10 false D 0.417,3.708 0.802,4.24 0.385,0.531 10 false G1 0.5,4.25 1.052,4.573 0.552,0.323 10 false PAON 1.323,4.25 1.875,4.573 0.552,0.323 10 false P-AB 0.938,1.146 1.49,1.469 0.552,0.323 10 false PAON 2.177,1.146 2.729,1.469 0.552,0.323 10 false P-AB 0.781,0.563 1.333,0.885 0.552,0.323 10 false G18
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Disconnect the connector from the combination meter assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-3 (PAON) - Body ground Power switch on (IG) Below 1 V
G1-4 (P-AB) - Body ground Power switch on (IG) Below 1 V



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



i.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (PAON) - G1-4 (P-AB) Always Below 1 Ω



k.

Disconnect the service wire from connector B.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (PAON) - G1-4 (P-AB) Always 1 MΩ or higher
G1-3 (PAON) - Body ground Always 1 MΩ or higher
G1-4 (P-AB) - Body ground Always 1 MΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and combination meter assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

7.CHECK INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE
a.
B483361C01
0.333,3.688 0.656,3.906 0.323,0.219 0.729,0.521 1.104,0.76 0.375,0.24 1.479,2.323 1.479,1.906 1.479,1.906 1.313,1.906 false 1.688,1.354 1.688,1.104 false 0.698,4.24 1.042,3.875 false 2.313,1.135 1.854,0.677 false 1.469,4.24 1.125,3.875 false 1.156,1.125 1.5,0.854 false 0.479,2.281 0.896,2.656 0.417,0.375 10 false *1 2.542,2.302 3.021,2.792 0.479,0.49 10 false *2 1.167,1.833 1.667,2.24 0.5,0.406 10 false *3 1.615,1.354 2.042,1.708 0.427,0.354 10 false *4 0.635,0.25 1.042,0.708 0.406,0.458 10 false *a 0.271,3.198 0.656,3.729 0.385,0.531 10 false *b 2.125,2.292 2.604,2.781 0.479,0.49 10 false A 1.74,2.292 2.219,2.781 0.479,0.49 10 false B 1.115,2.292 1.594,2.781 0.479,0.49 10 false C 0.729,2.292 1.208,2.781 0.479,0.49 10 false D 0.417,3.708 0.802,4.24 0.385,0.531 10 false G1 0.5,4.25 1.052,4.573 0.552,0.323 10 false PAON 1.323,4.25 1.875,4.573 0.552,0.323 10 false P-AB 0.938,1.146 1.49,1.469 0.552,0.323 10 false PAON 2.177,1.146 2.729,1.469 0.552,0.323 10 false P-AB 0.781,0.563 1.333,0.885 0.552,0.323 10 false G18
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-3 (PAON) - Body ground Power switch on (IG) Below 1 V
G1-4 (P-AB) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



f.

Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (PAON) - G1-4 (P-AB) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-3 (PAON) - G1-4 (P-AB) Always 1 MΩ or higher
G1-3 (PAON) - Body ground Always 1 MΩ or higher
G1-4 (P-AB) - Body ground Always 1 MΩ or higher




OK

8.CHECK COMBINATION METER ASSEMBLY (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK COMBINATION METER ASSEMBLY (SOURCE VOLTAGE)
a.
B483362C01
0.406,2.198 0.75,2.438 0.344,0.24 1.375,0.26 1.542,0.26 1.542,0.26 1.542,0.76 false 0.771,2.854 0.948,2.594 false 0.563,0.719 0.958,1.302 0.396,0.583 10 false *1 2.594,0.719 3.042,1.25 0.448,0.531 10 false *2 1.219,0.177 1.698,0.594 0.479,0.417 10 false *3 0.365,1.792 0.823,2.438 0.458,0.646 10 false *a 2.198,0.719 2.646,1.25 0.448,0.531 10 false A 1.823,0.719 2.271,1.25 0.448,0.531 10 false B 1.188,0.719 1.635,1.25 0.448,0.531 10 false C 0.813,0.719 1.26,1.25 0.448,0.531 10 false D 0.5,2.24 0.979,2.656 0.479,0.417 10 false G1 0.677,2.865 1.156,3.281 0.479,0.417 10 false IG+
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G1-21 (IG+) - Body ground Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

9.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR AUXILIARY BATTERY

9.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C239225C04
0.969,2.281 1.302,2.51 0.333,0.229 2.073,2.406 2.365,2.865 false 1.74,2.583 1.563,2.854 false 1.49,0.802 1.49,0.26 1.49,0.26 1.333,0.26 false 1.167,0.188 1.677,0.51 0.51,0.323 10 false *3 0.833,1.865 1.188,2.219 0.354,0.354 10 false *a 0.583,0.781 1.104,1.115 0.521,0.333 10 false *1 2.531,0.813 2.865,1.302 0.333,0.49 10 false *2 1.344,2.875 1.896,3.167 0.552,0.292 10 false PAON 1.01,2.313 1.448,2.74 0.438,0.427 10 false G18 2.219,2.875 2.74,3.135 0.521,0.26 10 false P-AB 1.75,0.781 2.042,1.167 0.292,0.385 10 false B 0.969,0.781 1.417,1.083 0.448,0.302 10 false D 1.125,0.781 1.438,1.188 0.313,0.406 10 false C 2.042,0.781 2.583,1.25 0.542,0.469 10 false A
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the connector to the combination meter assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.

Check the indicator according to the conditions in the table below.

OK:
Terminal Connection Condition Specified Condition
G18-23 (PAON) - Body ground Power switch on (IG) "ON" comes on
G18-17 (P-AB) - Body ground Power switch on (IG) "OFF" comes on



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

10.CHECK DTC

NG

REPLACE COMBINATION METER ASSEMBLY

10.CHECK DTC
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Combination Meter Assembly
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1660/43 is not output.


HINT:

Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.




OK

NG