Home › Vehicle Interior › DOOR LOCK › DOOR CONTROL SWITCH › from 2017.06
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278070 DOOR CONTROL SWITCH G

DOOR LOCK  DOOR CONTROL SWITCH  INSPECTION  


PROCEDURE

Hide 84820 1.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

a.

Check the operation of the power window regulator master switch assembly. (for LHD and w/o Canister Pump Module)

i.
B302422C54
2.346,1.682 2.346,0.921 2.346,0.921 2.651,0.921 false 1.11,1.684 1.11,0.967 1.11,0.967 0.841,0.967 false 2.188,1.69 2.188,0.469 2.188,0.469 2.615,0.469 false 0.206,0.217 0.398,0.388 0.192,0.171 10 *a 2.69,0.838 2.801,0.981 0.111,0.143 10 E 2.653,0.394 2.748,0.534 0.095,0.140 10 L 0.593,0.892 0.803,1.032 0.209,0.140 10 UL
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
Lock switch not pushed 10 kΩ or higher
9 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
Unlock switch pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch.



b.

Check the operation of the power window regulator master switch assembly. (for LHD and w/ Canister Pump Module)

i.
B302422C53
2.344,1.677 2.344,0.917 2.344,0.917 2.646,0.917 false 1.25,1.688 1.25,0.969 1.25,0.969 0.979,0.969 false 2.188,1.688 2.188,0.469 2.188,0.469 2.615,0.469 false 0.208,0.219 0.396,0.385 0.188,0.167 10 false *a 2.688,0.833 2.875,1.042 0.188,0.208 10 false E 2.656,0.396 2.792,0.594 0.135,0.198 10 false L 0.792,0.896 1.031,1.073 0.24,0.177 10 false UL
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 1 (E) Lock switch pushed Below 1 Ω
Lock switch not pushed 10 kΩ or higher
8 (UL) - 1 (E) Unlock switch pushed Below 1 Ω
Unlock switch pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch.



c.

Check the operation of the power window regulator master switch assembly. (for RHD)

i.
B302422C55
1.25,1.688 1.25,0.583 1.25,0.583 0.948,0.583 false 1.094,1.688 1.094,1.031 1.094,1.031 0.823,1.031 false 2.188,1.688 2.188,0.469 2.188,0.469 2.615,0.469 false 0.208,0.219 0.396,0.385 0.188,0.167 10 false *a 0.667,0.948 0.781,1.094 0.115,0.146 10 false E 2.656,0.396 2.75,0.531 0.094,0.135 10 false L 0.688,0.5 0.896,0.635 0.208,0.135 10 false UL
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (L) - 9 (E) Lock switch pushed Below 1 Ω
Lock switch not pushed 10 kΩ or higher
8 (UL) - 9 (E) Unlock switch pushed Below 1 Ω
Unlock switch pushed 10 kΩ or higher


If the result is not as specified, replace the power window regulator master switch.