Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT LEVELING SWITCH › from 2017.06
RM2170E _59 Vehicle Exterior _057049 LIGHTING (EXT) _0278191 HEADLIGHT LEVELING SWITCH G

LIGHTING (EXT)  HEADLIGHT LEVELING SWITCH  INSPECTION  


PROCEDURE

Hide 84152 1.INSPECT HEADLIGHT LEVELING SWITCH (w/ Canister Pump Module)

E190203C15
1.327,1.471 0.904,1.86 false 1.83,1.471 1.944,1.86 false 0.792,1.879 0.944,2.042 0.152,0.163 10 E 1.936,1.879 2.064,2.042 0.128,0.163 10 T 2.105,1.471 2.529,1.86 false 2.537,1.879 2.665,2.042 0.128,0.163 10 B 0.181,0.149 0.435,0.312 0.254,0.163 10 *a
*a Component without harness connected
(Headlight Leveling Switch)


a.

Voltage Check

i.

Connect a positive (+) lead from the auxiliary battery to terminal 1 (B) and a negative (-) lead to terminal 4 (E).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Position Specified Condition
2 (T) - 4 (E) 0 8.7 to 13.0 V
1 7.6 to 11.5 V
2 6.6 to 10.0 V
3 5.5 to 8.5 V
4 4.4 to 7.0 V
5 3.4 to 5.6 V


HINT:

Auxiliary battery voltage is 12 V.


If the result is not as specified, replace the headlight leveling switch.



b.
E190203C16
1.327,1.471 0.904,1.86 false 1.573,1.471 1.996,1.86 false 0.792,1.879 0.945,2.042 0.153,0.163 10 E 1.884,1.879 2.179,2.042 0.295,0.163 10 ILL+ 0.181,0.149 0.435,0.312 0.255,0.163 10 *a
*a Component without harness connected
(Headlight Leveling Switch)


Illumination Inspection

i.

Apply auxiliary battery voltage to the headlight leveling switch and check that the switch illuminates.

OK:
Tester Connection Specified Condition
Auxiliary battery positive (+) → Terminal 3 (ILL+)
Auxiliary battery negative (-) → Terminal 4 (E)
Illuminates


If the result is not as specified, replace the headlight leveling switch.



Hide 84152 2.INSPECT HEADLIGHT LEVELING SWITCH (w/o Canister Pump Module)

E371712C01
1.052,1.875 1.323,1.469 false 1.906,1.865 1.906,1.448 false 2.406,1.865 2.135,1.458 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 1,1.896 1.313,2.094 0.313,0.198 10 false E 1.875,1.906 2.188,2.104 0.313,0.198 10 false T 2.406,1.896 2.719,2.094 0.313,0.198 10 false B
*a Component without harness connected
(Headlight Leveling Switch)


a.

Voltage Check

i.

Connect a positive (+) lead from the auxiliary battery to terminal 1 (B) and a negative (-) lead to terminal 5 (E).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Position Specified Condition
2 (T) - 5 (E) 0 8.7 to 13.0 V
1 7.6 to 11.5 V
2 6.6 to 10.0 V
3 5.5 to 8.5 V
4 4.4 to 7.0 V
5 3.4 to 5.6 V


HINT:

Auxiliary battery voltage is 12 V.


If the result is not as specified, replace the headlight leveling switch.



b.
E371712C02
1.427,1.833 1.531,1.427 false 1.802,1.813 1.698,1.427 false 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 1.313,1.844 1.667,2.042 0.354,0.198 10 false ILL- 1.76,1.844 2.167,2.042 0.406,0.198 10 false ILL+
*a Component without harness connected
(Headlight Leveling Switch)


Illumination Inspection

i.

Apply auxiliary battery voltage to the headlight leveling switch and check that the switch illuminates.

OK:
Tester Connection Specified Condition
Auxiliary battery positive (+) → Terminal 3 (ILL+)
Auxiliary battery negative (-) → Terminal 4 (ILL-)
Illuminates


If the result is not as specified, replace the headlight leveling switch.