Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A2B-250  Drive Motor "A" Temperature Sensor Circuit Range / Performance  P0A2E-248  Drive Motor "A" Temperature Sensor Circuit Intermittent  


DESCRIPTION

The resistance of the thermistor built into the motor temperature sensor changes in accordance with changes in MG2 temperature. The lower the MG2 temperature, the higher the thermistor resistance. Conversely, the higher the MG2 temperature, the lower the resistance.

HINT:

The term "drive motor A" indicates MG2.


A172965E06
2.044,0.334 2.299,0.484 0.255,0.151 10 120 2.044,0.477 2.299,0.628 0.255,0.151 10 110 2.044,0.617 2.299,0.768 0.255,0.151 10 100 2.119,0.747 2.299,0.898 0.180,0.151 10 90 2.126,0.88 2.299,1.031 0.173,0.151 10 80 2.119,1.017 2.299,1.167 0.180,0.151 10 70 2.119,1.146 2.299,1.297 0.180,0.151 10 60 2.119,1.279 2.299,1.430 0.180,0.151 10 50 2.119,1.419 2.299,1.570 0.180,0.151 10 40 2.119,1.559 2.299,1.710 0.180,0.151 10 30 2.119,1.693 2.299,1.843 0.180,0.151 10 20 2.119,1.833 2.299,1.983 0.180,0.151 10 10 0.9,1.055 1.934,1.206 1.034,0.151 10 Resistance (kΩ) 5.481,2.239 6.967,2.390 1.486,0.151 10 Temperature (°C (°F )) 2.312,2.169 2.492,2.320 0.180,0.151 10 10 2.256,2.319 2.536,2.470 0.281,0.151 10 (50) 2.725,2.319 3.006,2.470 0.281,0.151 10 (59) 3.18,2.319 3.461,2.470 0.281,0.151 10 (68) 3.646,2.319 3.927,2.470 0.281,0.151 10 (77) 4.108,2.319 4.389,2.470 0.281,0.151 10 (86) 4.557,2.319 4.838,2.470 0.281,0.151 10 (95) 4.965,2.319 5.309,2.470 0.343,0.151 10 (104) 2.753,2.169 2.933,2.320 0.180,0.151 10 15 3.229,2.169 3.409,2.320 0.180,0.151 10 20 3.695,2.169 3.875,2.320 0.180,0.151 10 25 4.143,2.169 4.324,2.320 0.180,0.151 10 30 4.595,2.169 4.808,2.320 0.213,0.151 10 35 5.047,2.169 5.325,2.320 0.277,0.151 10 40 2.193,1.962 2.300,2.113 0.107,0.151 10 0

DTC No. INF Code DTC Detection Condition Trouble Area
P0A2B 250 w/o Canister Pump Module:
Motor temperature sensor output does not increase under conditions in which the value should increase, or output does not decrease under conditions in which the value should decrease.
·

Wire harness or connector

·

Hybrid vehicle transaxle assembly (Motor temperature sensor)


w/ Canister Pump Module:
After a long soak, the value of the motor (MG2) temperature sensor is different from the value of the other temperature sensors.
P0A2E 248 Unusual sudden change in motor temperature sensor output occurs and the condition continues, or unusual sudden change in motor temperature sensor output occurs repeatedly.

WIRING DIAGRAM

A407382E21
2.302,1.938 2.76,2.135 0.458,0.198 10 false 1 1.802,1.938 2.563,2.26 0.76,0.323 10 false MMTG 1.906,1.188 2.667,1.51 0.76,0.323 10 false MMT 2.302,1.188 2.76,1.385 0.458,0.198 10 false 2 0.24,2.667 1,2.99 0.76,0.323 10 false C25 0.26,2.844 2.458,3.521 2.198,0.677 10 false Hybrid Vehicle Transaxle Assembly (Motor Temperature Sensor) 2.552,2.667 4.563,3.521 2.01,0.854 10 false No. 1 Engine Room Relay Block Assembly Connector 2.542,2.5 3.302,2.823 0.76,0.323 10 false CA1 3.042,1.177 3.802,1.5 0.76,0.323 10 false 10 3.042,1.938 3.802,2.26 0.76,0.323 10 false 21 3.688,1.938 4.448,2.26 0.76,0.323 10 false 21 3.677,1.177 4.438,1.5 0.76,0.323 10 false 10 4.615,1.188 5.375,1.51 0.76,0.323 10 false 24 4.885,1.188 5.646,1.51 0.76,0.323 10 false MMT 4.625,1.948 5.385,2.271 0.76,0.323 10 false 23 4.875,1.938 5.635,2.26 0.76,0.323 10 false MMTG 4.948,2.688 5.708,3.01 0.76,0.323 10 false A71 4.938,2.833 6.646,3.51 1.708,0.677 10 false Hybrid Vehicle Control ECU 5.958,1.302 6.719,1.625 0.76,0.323 10 false ADC

CAUTION / NOTICE / HINT

HINT:

w/o Canister Pump Module:

·

If DTC P0A2B-250 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Drive the vehicle (stop and go driving) on urban roads for approximately 5 minutes. If the Data List item "Motor Temp No1" shows both increases and decreases in temperature, suspected areas indicated by this DTC are not malfunctioning.


·

If DTC P0A2E-248 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Turn the power switch on (READY) and wait for 30 seconds or more.

(b)

Drive the vehicle for approximately 5 minutes according to the freeze frame data items "Vehicle Spd", "Motor Temp No1" and "Motor Temp No2".



w/ Canister Pump Module:

·

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Turn the power switch on (Ready), wait for 10 seconds or more and turn the power switch off.

(b)

Leave the vehicle as is for 5 hours or more and then check that the values of the Data List items "Motor Temp No1", "Motor Temp No2" and "Inverter Coolant Water Temperature" are approximately the same.




PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

2.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
a.
A448677C07
0.094,2.365 0.448,2.594 0.354,0.229 0.719,2.51 0.521,2.958 true 0.771,2.5 1.083,2.969 true 0.125,0.344 0.438,0.542 0.313,0.198 10 false *a 0.156,2.406 0.615,2.604 0.458,0.198 10 false A71 0.354,3 0.813,3.198 0.458,0.198 10 false MMT 0.979,3.01 1.594,3.208 0.615,0.198 10 false MMTG
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Disconnect the A71 hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-24 (MMT) - A71-23 (MMTG) Power switch off 0.3436 to 1442 kΩ



c.

Reconnect the A71 hybrid vehicle control ECU connector.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)

NG

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
3.CHECK CONNECTOR CONNECTION CONDITION (ENGINE ROOM RELAY BLOCK NO. 1 CA1 CONNECTOR)
a.
A448676

Check the connection condition of the engine room relay block No. 1 CA1connector and the contact pressure of each terminal. Check the terminals for deformation, and check the connector for water ingress and foreign matter.

OK:

- The connector is connected securely.

- The terminals are not deformed and are connected securely.

- No water or foreign matter in the connector.



Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ENGINE ROOM RELAY BLOCK NO. 1)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ENGINE ROOM RELAY BLOCK NO. 1)
a.

Disconnect the CA1 engine rool relay block No. 1 connector.


b.

Disconnect the A71 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


A448678C08
4.781,1.708 5.167,2 0.385,0.292 0.302,1.313 0.688,1.604 0.385,0.292 4.333,1.938 4,2.313 true 4.375,1.938 4.677,2.26 true 1.333,1.354 1.688,0.74 true 1.333,1.594 1.594,2.198 true 0.542,0.219 0.854,0.417 0.313,0.198 10 false *a 3.625,0.229 3.938,0.427 0.313,0.198 10 false *b 0.396,1.375 0.854,1.573 0.458,0.198 10 false CA1 4.854,1.792 5.313,1.99 0.458,0.198 10 false A71 3.76,2.333 4.375,2.531 0.615,0.198 10 false MMT 1.583,0.552 2.042,0.75 0.458,0.198 10 false MMT 4.583,2.333 5.042,2.531 0.458,0.198 10 false MMTG 1.5,2.26 2.115,2.458 0.615,0.198 10 false MMTG
*a Front view of wire harness connector
(to Engine rool relay block No. 1)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
CA1-10 (MMT) - A71-24 (MMT) Power switch off Below 1 Ω
CA1-21 (MMTG) - A71-23 (MMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
CA1-10 (MMT) - Other terminals Power switch off 10 kΩ or higher
CA10-21 (MMTG) - Other terminals Power switch off 10 kΩ or higher



d.

Reconnect the A71 hybrid vehicle control ECU connector.


e.

Reconnect the CA1 engine rool relay block No. 1 connector.



OK

5.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CONNECTOR CONNECTION CONDITION (MOTOR TEMPERATURE SENSOR CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A2C-247

Result:
Result Proceed to
OK A
NG (The connector is not connected securely.) B
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) C



A

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK NO. 1 - HYBRID VEHICLE TRANSAXLE ASSEMBLY)

B

CONNECT SECURELY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK NO. 1 - HYBRID VEHICLE TRANSAXLE ASSEMBLY)
a.

Disconnect the CA1 engine room relay block No. 1 connector.


b.

Disconnect the C25 motor temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

HINT:

When performing the measurement, lightly jiggle the wire harness up and down and left and right and confirm that the resistance does not fluctuate.


A448679C03
3.656,1.24 4.031,1.51 0.375,0.271 0.719,1.26 1.094,1.531 0.375,0.271 1.438,2.083 1.688,1.5 true 2.26,2.083 1.927,1.5 true 5.729,2.177 5.604,1.646 true 5.583,1.344 5.719,0.708 true 0.573,0.5 0.885,0.698 0.313,0.198 10 false *a 3.729,0.427 4.042,0.625 0.313,0.198 10 false *b 0.76,1.323 1.219,1.521 0.458,0.198 10 false C25 5.646,2.25 6.26,2.448 0.615,0.198 10 false MMTG 2.177,2.167 2.792,2.365 0.615,0.198 10 false MMT 1.156,2.177 1.771,2.375 0.615,0.198 10 false MMTG 5.656,0.5 6.271,0.698 0.615,0.198 10 false MMT 3.74,1.292 4.198,1.49 0.458,0.198 10 false CA1
*a Front view of wire harness connector
(to Motor Temperature Sensor)
*b Front view of wire harness connector
(to Engine Rool Relay Block No. 1)


Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
CA1-10 (MMT) - C25-2 (MMT) Power switch off Below 1 Ω
CA1-21 (MMTG) - C25-1 (MMTG) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
CA1-10 (MMT) - Other terminals Power switch off 10 kΩ or higher
CA1-21 (MMTG) - Other terminals Power switch off 10 kΩ or higher



d.

Reconnect the C25 motor temperature sensor connector.


e.

Reconnect the CA1 engine room relay block No. 1 connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
a.

Disconnect the CA1 engine rool relay block No. 1 connector.


b.
A448674C02
0.115,0.99 0.521,1.25 0.406,0.26 2.448,1.073 2.771,0.458 true 2.438,1.438 2.74,1.792 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 0.198,1.052 0.656,1.25 0.458,0.198 10 false CA1 2.688,1.823 3.146,2.021 0.458,0.198 10 false MMTG 2.635,0.271 3.25,0.469 0.615,0.198 10 false MMT
*a Front view of wire harness connector
(to Engine Rool Relay Block No. 1)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
CA1-10 (MMT) - CA1-21 (MMTG) Power switch off 0.3436 to 1442 kΩ



c.

Reconnect the CA1 engine rool relay block No. 1 connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

8.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)
8.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR TEMPERATURE SENSOR)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG