Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2017.06
RM2170E _51 Engine / Hybrid System _057004 HYBRID / BATTERY CONTROL _0277924 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P314A-828  Inverter Coolant Pump Speed Signal  


DESCRIPTION

Refer to the description for DTC P0C73-776 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C73-776).

The inverter water pump assembly sends the water pump speed (measured value) signal to the hybrid vehicle control ECU. If the inverter water pump speed (measured value) signal is not sent to the hybrid vehicle control ECU when the power switch is on (READY), this DTC is stored.

DTC No. INF Code DTC Detection Condition Trouble Area
P314A 828 The water pump speed signal is not sent to the hybrid vehicle control ECU when the power switch is turned on (READY) or water pump revolution speed is extremely low or stop.*1
(1 trip detection logic)
·

Wire harness or connector

·

Hybrid vehicle control ECU

·

Inverter water pump assembly

·

IGCT NO. 3 fuse

·

IGCT relay



·

*1: Malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly or inverter water pump assembly power source circuit malfunction is suspected.

·

A malfunction (open, short to +B or short to ground) in the speed signal line from the inverter water pump assembly to the hybrid vehicle control computer is detected.

·

A malfunction in the inverter water pump assembly power source circuit is detected.

·

A malfunction in the +B line or speed signal line to the inverter water pump assembly is detected.

·

A malfunction in the inverter water pump assembly power source circuit or hybrid vehicle control computer power source circuit is detected.


Related Data List
DTC No. Data List
P314A-828
·

Inverter W/P Revolution*2

·

W/P Run Control Duty*2

·

Ready Signal



*2: This Data List item is related to the inverter water pump assembly.


Related Active Test
DTC No. Active Test
P314A-828 Activate the Water Pump*3

*3: This is an Active Test of the inverter water pump assembly.


WIRING DIAGRAM

Refer to the wiring diagram for DTC P0C73-776 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0C73-776).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 2 minutes or more.



PROCEDURE

1.CLEAR DTC

NEXT

2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE WATER PUMP)
2.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.


d.

Perform the Activate the Water Pump Active Test.


e.

Touch the inverter water pump assembly and check that it is operating (vibrating).

OK:

The inverter water pump is operating (vibrating).



f.

Turn the power switch off.



OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

4.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect connector A71 from the hybrid vehicle control ECU.


b.

Disconnect connector A53 from the inverter water pump assembly.


c.

Measure the resistance according to the value(s) in the table below.

A265405C56
0.417,1.729 0.792,1.958 0.375,0.229 4.375,1.292 4.75,1.521 0.375,0.229 0.844,2.24 1.083,1.823 false 5.031,1.875 5.302,1.469 false 0.49,1.771 0.792,1.938 0.302,0.167 10 false A71 0.688,2.25 1.063,2.448 0.375,0.198 10 false NIWP 0.323,0.354 0.573,0.542 0.25,0.188 10 false *a 4.573,0.813 4.75,0.979 0.177,0.167 10 false *b 4.448,1.323 4.771,1.531 0.323,0.208 10 false A53 4.906,1.896 5.26,2.115 0.354,0.219 10 false NWP
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A71-14 (NIWP) - A53-2 (NWP) Power switch off Below 1 Ω
A71-14 (NIWP) or A53-2 (NWP) -Body ground and other terminals Power switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Connect the hybrid vehicle control ECU connector.


e.

Connect the inverter water pump assembly connector.



OK

6.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect connector A53 from the inverter water pump assembly.


b.

Turn the power switch on (IG).


c.
A372725C24
0.625,0.958 0.969,1.24 0.344,0.281 1.854,0.958 2.198,1.24 0.344,0.281 1.823,1.719 2.156,2.531 false 0.719,1.781 0.625,2.479 false 0.115,0.125 0.427,0.323 0.313,0.198 10 false *a 0.688,1.021 1.146,1.219 0.458,0.198 10 false A71 1.906,1.021 2.365,1.219 0.458,0.198 10 false G80 0.5,2.573 0.958,2.771 0.458,0.198 10 false NIWP 2.125,2.583 2.583,2.781 0.458,0.198 10 false E1
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A71-14 (NIWP) - G80-6 (E1) Power switch on (IG) 11 to 14 V



d.

Turn the power switch off.


e.

Connect the inverter water pump assembly connector.



OK

7.CLEAR DTC

NG

7.CLEAR DTC

NEXT

8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE WATER PUMP)
8.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE WATER PUMP)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.


d.

Perform the "Activate the Water Pump" Active Test.


e.
A356773C06
0.635,0.469 1.135,0.719 0.5,0.25 1.688,0.469 2.188,0.719 0.5,0.25 0.573,1.802 0.833,1.25 true 1.552,1.802 1.771,1.198 true 0.229,0.323 0.542,0.479 0.313,0.156 10 false *a 0.771,0.521 1.146,0.719 0.375,0.198 10 false A71 1.802,0.521 2.177,0.719 0.375,0.198 10 false G80 0.448,1.833 0.875,2.01 0.427,0.177 10 false NIWP 1.5,1.833 1.813,1.99 0.313,0.156 10 false E1 1.49,3.646 1.656,3.833 0.167,0.188 10 true A 2.802,3.344 3.26,3.542 0.458,0.198 10 false GND
*a Component with harness connected
(Hybrid Vehicle Control ECU)


Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal A71-14 (NIWP) - G80-6 (E1)
Equipment Setting 5 V/DIV., 100 ms./DIV.
Condition Powern switch ON (IG), during Active Test

OK:

The duration of wavelength A is 300 msec or less.



f.

Turn the power switch off.



OK

NG

27.REPLACE INVERTER WATER PUMP ASSEMBLY
9.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

OK

10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)

NG

12.CHECK FUSE (IGCT NO. 3)
10.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - IGCT RELAY)
a.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Disconnect connector A53 from the inverter water pump assembly.


c.

Measure the resistance according to the value(s) in the table below.

A298744C06
0.677,1.302 1.094,1.552 0.417,0.25 1.969,1.479 2.24,1.948 false 0.792,1.354 1.094,1.542 0.302,0.188 10 false A53 0.865,0.792 1.167,0.979 0.302,0.188 10 false *a 3.406,0.333 3.708,0.521 0.302,0.188 10 false *1 6.104,0.927 6.406,1.115 0.302,0.188 10 false *2 2.083,2 2.5,2.188 0.417,0.188 10 false +BWP
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT Relay
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A53-4 (+BWP) - 5 (IGCT relay) Power switch off Below 1 Ω


HINT:
·

Connectors

Slightly shake the connector vertically and horizontally.

·

Wire Harness

Slightly shake the wire harness vertically and horizontally.

The connector joint and fulcrum of the vibration are the major areas that should be checked thoroughly.

·

No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly

Apply slight vibration with a finger to the No. 2 engine room relay block and No. 2 junction block assembly and check whether a malfunction occurs.

·
A288054E02
0.139,0.08 0.359,0.293 0.220,0.213 10 *a 0.92,1.316 1.141,1.529 0.220,0.213 10 *b 1.438,2.647 1.659,2.860 0.220,0.213 10 *c

IGCT NO. 3 Fuse

Apply slight vibration with a finger to the IGCT NO. 3 fuse and check whether a malfunction occurs.

Text in Illustration
*a Example
*b Shake Slightly
*c Vibrate Slightly



NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



d.

Install the IGCT relay.


e.

Connect the inverter water pump assembly connector.



OK

11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)

NG

13.CHECK INSTALLATION CONDITION (IGCT NO. 3 FUSE)
11.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect connector A53 from the inverter water pump assembly.


b.
A288050C76
1.49,1.052 1.896,1.302 0.406,0.25 1.125,2.448 1.365,1.896 false 0.177,0.188 0.49,0.344 0.313,0.156 10 false *a 0.99,2.5 1.448,2.698 0.458,0.198 10 false GND 1.594,1.104 1.917,1.271 0.323,0.167 10 false A53
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A53-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Connect the inverter water pump assembly connector.



OK

27.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK FUSE (IGCT NO. 3)
a.
A263625C04
0.252,0.216 0.431,0.386 0.179,0.170 10 *1 2.575,2.84 2.727,3.010 0.151,0.170 10 *2 2.496,2.418 2.648,2.826 false
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT NO. 3 Fuse


Remove the IGCT NO. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 3 fuse Always Below 1Ω



c.

Install the IGCT NO. 3 fuse.



OK

CONNECT SECURELY (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

24.CONNECT SECURELY
13.CHECK INSTALLATION CONDITION (IGCT NO. 3 FUSE)
a.

Check the terminals of the IGCT NO. 3 fuse holder.

OK:

The terminals of the IGCT NO. 3 fuse holder are not bent, loose or corroded.




OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)

NG

16.CHECK FUSE HOLDER TERMINAL (IGCT NO. 3 FUSE)
14.CHECK HARNESS AND CONNECTOR (INVERTER WATER PUMP ASSEMBLY CIRCUIT)
a.

Remove the IGCT NO. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Remove the IGCT relay from the No. 2 engine room relay block and No. 2 junction block assembly.


c.

Disconnect connector A53 from the inverter water pump assembly.


d.

Measure the resistance according to the value(s) in the table below.

A298745C05
0.688,1.292 1.104,1.563 0.417,0.271 1.938,1.49 2.302,2.063 false 3.719,0.229 4.031,0.427 0.313,0.198 10 false *1 4.948,2.021 5.26,2.219 0.313,0.198 10 false *2 6.146,0.615 6.458,0.813 0.313,0.198 10 false *3 0.865,0.802 1.177,1 0.313,0.198 10 false *a 0.802,1.354 1.115,1.552 0.313,0.198 10 false A53 2.167,2.104 2.542,2.302 0.375,0.198 10 false +BWP
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly *2 IGCT NO. 3 Fuse
*3 IGCT Relay - -
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)
- -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
A53-4 (+BWP) - 2 (IGCT NO. 3 fuse) Power switch off Below 1 Ω
1 (IGCT NO. 3 fuse) - 5 (IGCT relay) Power switch off Below 1 Ω
A53-4 (+BWP) or 2 (IGCT NO. 3 fuse) - Body ground and other terminals Powern switch off 10 kΩ or higher
1 (IGCT NO. 3 fuse) or 5 (IGCT relay) - Body ground and other terminals Power switch off 10 kΩ or higher


NOTICE:

Do not apply excessive force when using the probes of the tester to perform the inspection. If excessive force is used, the terminals will be damaged.



e.

Install the IGCT NO. 3 fuse.


f.

Install the IGCT relay.


g.

Connect the inverter water pump assembly connector.



OK

15.CHECK FUSE (IGCT NO. 3)

NG

18.CHECK FUSE (IGCT NO. 3)
15.CHECK FUSE (IGCT NO. 3)
a.
A263625C05
0.252,0.216 0.431,0.386 0.179,0.170 10 *1 2.575,2.84 2.727,3.010 0.151,0.170 10 *2 2.496,2.418 2.648,2.826 false
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT NO. 3 Fuse


Remove the IGCT NO. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 3 fuse Always Below 1Ω



c.

Install the IGCT NO. 3 fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

19.CHECK HARNESS AND CONNECTOR ((INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
16.CHECK FUSE HOLDER TERMINAL (IGCT NO. 3 FUSE)
a.

Check the terminals of the IGCT NO. 3 fuse holder.

OK:

The terminals of the IGCT NO. 3 fuse holder are not bent, loose or corroded.




OK

17.CHECK FUSE (IGCT NO. 3)

NG

23.CHECK FUSE (IGCT NO. 3)
17.CHECK FUSE (IGCT NO. 3)
a.
A263625C06
2.5,2.417 2.646,2.823 false 0.25,0.219 0.427,0.385 0.177,0.167 10 false *1 2.573,2.844 2.719,3.01 0.146,0.167 10 false *2
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT NO. 3 Fuse


Remove the IGCT NO. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 3 fuse Always Below 1Ω



c.

Install the IGCT NO. 3 fuse.



OK

CONNECT SECURELY (IGCT NO. 3 FUSE)

NG

REPLACE FUSE (IGCT NO. 3)

18.CHECK FUSE (IGCT NO. 3)
a.
A263625C06
2.5,2.417 2.646,2.823 false 0.25,0.219 0.427,0.385 0.177,0.167 10 false *1 2.573,2.844 2.719,3.01 0.146,0.167 10 false *2
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT NO. 3 Fuse


Remove the IGCT NO. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 3 fuse Always Below 1Ω



c.

Install the IGCT NO. 3 fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
19.CHECK HARNESS AND CONNECTOR ((INVERTER WATER PUMP ASSEMBLY - BODY GROUND)
a.

Disconnect connector A53 from the inverter water pump assembly.


b.
A288050C77
1.49,1.063 1.906,1.302 0.417,0.24 1.125,2.448 1.365,1.896 false 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 0.99,2.5 1.448,2.698 0.458,0.198 10 false GND 1.594,1.104 1.979,1.333 0.385,0.229 10 false A53
*a Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A53-1 (GND) - Body ground Power switch off Below 1 Ω



c.

Connect the inverter water pump assembly connector.



OK

20.CHECK FUSE HOLDER TERMINAL (IGCT NO. 3 FUSE)

NG

25.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.CHECK FUSE HOLDER TERMINAL (IGCT NO. 3 FUSE)
a.

Check the terminals of the IGCT NO. 3 fuse holder.

OK:

The terminals of the IGCT NO. 3 fuse holder are not bent, loose or corroded.




OK

21.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

26.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 3 FUSE HOLDER TERMINAL)
21.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

22.ADD HV COOLANT AND PERFORM AIR BLEEDING
22.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COOLANT(for Inverter)>REPLACEMENT



NEXT

REPLACE FUSE (IGCT NO. 3)

23.CHECK FUSE (IGCT NO. 3)
a.
A263625C06
2.5,2.417 2.646,2.823 false 0.25,0.219 0.427,0.385 0.177,0.167 10 false *1 2.573,2.844 2.719,3.01 0.146,0.167 10 false *2
*1 No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
*2 IGCT NO. 3 Fuse


Remove the IGCT NO. 3 fuse from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 3 fuse Always Below 1Ω



c.

Install the IGCT NO. 3 fuse.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

26.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 3 FUSE HOLDER TERMINAL)
24.CONNECT SECURELY
a.

Connect the inverter water pump assembly connector securely.



NEXT

REPLACE FUSE (IGCT NO. 3)

25.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (IGCT NO. 3)

26.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGCT NO. 3 FUSE HOLDER TERMINAL)

NEXT

REPLACE FUSE (IGCT NO. 3)

27.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

28.ADD HV COOLANT AND PERFORM AIR BLEEDING
28.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>COOLANT(for Inverter)>REPLACEMENT



NEXT

COMPLETED