Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057037 METER / GAUGE / DISPLAY _0278095 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1503  Exhaust Heat Management Warning Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a malfunction in the water temperature sensor that is connected to the combination meter assembly via a direct line.

DTC No. DTC Detection Condition Trouble Area
B1503 When IG voltage is 9.5 V or more and any of the following conditions is detected:
1.

Engine coolant temperature sensor operation malfunction

2.

Engine coolant temperature sensor circuit is open or shorted

3.

Engine coolant temperature is 120°C (248°F) or more


·

Harness or connector

·

Water temperature sensor

·

Combination meter assembly



HINT:

This DTC is for the water temperature sensor which is used to detect the engine coolant temperature for the exhaust heat recirculation system, not for the engine coolant temperature sensor which is used for the SFI system.


WIRING DIAGRAM

E230581E15
2.229,0.896 2.344,1.042 0.115,0.146 10 false 1 2.229,2.219 2.344,2.365 0.115,0.146 10 false 2 1.948,0.896 2.25,1.104 0.302,0.208 10 false E2 1.74,2.229 2.375,2.51 0.635,0.281 10 false TWS3 0.667,3 1.125,3.177 0.458,0.177 10 false A84 0.656,3.156 2.375,3.469 1.719,0.313 10 false Water Temperature Sensor 5.031,2.885 5.313,3.063 0.281,0.177 10 false G1 5.031,3.031 6.927,3.375 1.896,0.344 10 false Combination Meter Assembly 5.323,0.885 5.594,1.052 0.271,0.167 10 false 36 5.583,1 5.948,1.229 0.365,0.229 10 false E2 5.323,2.229 5.552,2.375 0.229,0.146 10 false 15 5.583,2.323 6.198,2.635 0.615,0.313 10 false TWS3

PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Set the vehicle in maintenance mode using the GTS (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Data List.


f.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature Min.: 0°C (32°F), Max.: 127.5°C (261.5°F) After warming up: 75 to 100°C (167 to 212°F) -

HINT:
·

The coolant temperature value in this inspection is the data sent from the engine coolant temperature sensor for the SFI system.

·

When the Data List values do not match, a signal output error of the ECM is suspected.



OK:

Engine coolant temperature displayed on the Techstream is 75 to 100°C (167 to 212°F) after warming up.




OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WATER TEMPERATURE SENSOR)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - WATER TEMPERATURE SENSOR)
a.

Disconnect the A84 water temperature sensor connector.


b.

Disconnect the G1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A84-2 (TWS3) - G1-15 (TWS3) Always Below 1 Ω
A84-1 (E2) - G1-36 (E2) Always Below 1 Ω
A84-2 (TWS3) or G1-15 (TWS3) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Remove the water temperature sensor (See page Engine / Hybrid System>1NZ-FXE (COOLING)>TEMPERATURE SWITCH>REMOVAL).

E319158E06
0.833,0.563 1.219,0.802 0.385,0.24 0.313,0.26 0.625,0.458 0.313,0.198 10 false *a 4.385,0.156 4.698,0.354 0.313,0.198 10 false *b 4.792,2.323 5.177,2.792 0.385,0.469 10 false -20 5.063,2.323 5.417,2.792 0.354,0.469 10 false 0 5.24,2.323 5.594,2.792 0.354,0.469 10 false 20 5.469,2.323 5.823,2.792 0.354,0.469 10 false 40 5.698,2.323 6.052,2.792 0.354,0.469 10 false 60 5.917,2.323 6.271,2.792 0.354,0.469 10 false 80 6.104,2.323 6.458,2.792 0.354,0.469 10 false 100 6.5,2.323 6.854,2.792 0.354,0.469 10 false *c 4.802,2.5 5.135,2.792 0.333,0.292 8 false (-4) 6.146,2.5 6.479,2.792 0.333,0.292 8 false (212) 5.875,2.5 6.208,2.792 0.333,0.292 8 false (176) 5.625,2.5 5.958,2.792 0.333,0.292 8 false (140) 5.385,2.5 5.719,2.792 0.333,0.292 8 false (104) 5.198,2.5 5.531,2.792 0.333,0.292 8 false (68) 5,2.5 5.333,2.792 0.333,0.292 8 false (32) 4.521,0.552 7.156,0.875 2.635,0.323 10 false 20 4.521,0.75 7.156,1.073 2.635,0.323 10 false 10 4.604,0.927 7.156,1.25 2.552,0.323 10 false 5 4.604,1.417 7.156,1.74 2.552,0.323 10 false 1 4.604,1.198 7.156,1.521 2.552,0.323 10 false 2 4.49,1.667 7.125,1.99 2.635,0.323 10 false 0.3 4.49,1.885 7.125,2.208 2.635,0.323 10 false 0.1 0.906,0.604 1.219,0.802 0.313,0.198 10 false A84


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A84-1 (E2) - A84-2 (TWS3) Temperature is 20°C (68°F) 2.32 to 2.59 kΩ
A84-1 (E2) - A84-2 (TWS3) Temperature is 80°C (176°F) 0.310 to 0.326 kΩ


Text in Illustration
*a Component without harness connected
(Water Temperature Sensor)
*b Resistance kΩ
*c Temperature °C (°F)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR