Home › Drivetrain › P510 (HYBRID TRANSMISSION / TRANSAXLE) › OIL PUMP › 2011.12–2017.06
RM2170E _52 Drivetrain _057013 P510 HYBRID TRANSMISSION / TRANSAXLE _0334374 OIL PUMP A

P510 HYBRID TRANSMISSION / TRANSAXLE  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 1.INSTALL OIL PUMP DRIVE SHAFT

a.

Install the oil pump drive shaft to the hybrid vehicle transaxle assembly.


Hide 2.INSTALL TRANSMISSION OIL PUMP DRIVE ROTOR

a.

Coat the transmission oil pump drive rotor with ATF.


b.

Install the transmission oil pump drive rotor to the hybrid vehicle transaxle assembly.


Hide 3.INSTALL TRANSMISSION OIL PUMP DRIVEN ROTOR

a.

Coat the transmission oil pump driven rotor with ATF.


b.

Install the transmission oil pump driven rotor to the hybrid vehicle transaxle assembly.


Hide 4.INSTALL TRANSMISSION OIL PUMP COVER SUB-ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the hybrid vehicle transaxle assembly.

NOTICE:

Be careful not to damage the O-ring.



b.
C392194

Install the transmission oil pump cover sub-assembly to the hybrid vehicle transaxle assembly with 3 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

Make sure that the O-ring is not cut or pinched during installation.



c.

Using SST, install the bolt.

C392195C01
3.333,2.302 3.781,2.302 false 4.833,1.719 5.281,1.719 false 4.667,1.448 4.188,1.323 4.188,1.323 4.677,1.177 false 5.688,0.302 5.938,0.552 0.25,0.25 10 false *a 5.323,1.625 5.719,1.854 0.396,0.229 10 false SST 3.813,2.198 4.25,2.427 0.438,0.229 10 false SST 4,1.229 4.302,1.438 0.302,0.208 10 false *b
*a Torque Wrench Fulcrum Length *b Socket Adapter


SST
09729-00120  09925-40010  (09926-02120)

Torque:
Specified Tightening Torque : 11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 200 mm (7.87 in.)) + torque wrench (fulcrum length of 185 mm (7.28 in.)):

5.3 N*m (54 kgf*cm, 47 in.*lbf)




d.

Install the fluid pump cover plug.

HINT:

Perform this procedure only when replacement of the fluid pump cover plug is necessary.


i.

Coat a new O-ring with ATF and install it to the fluid pump cover plug.


ii.

Install the fluid pump cover plug to the transmission oil pump cover sub-assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)



Hide 5.INSTALL UNION

a.

Coat a new O-ring with ATF and install it to the union.


b.

Install the union to the transmission oil pump cover sub-assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide G1250 6.CONNECT MOTOR COOLING PIPE ASSEMBLY

a.

Temporarily install the motor cooling pipe assembly to the union.


b.

Install the oil cooler tube clamp and motor cooling pipe assembly to the No. 1 transmission control cable bracket with the bolt.

Torque:
12 N*m (117 kgf*cm, 8 ft.*lbf)


c.
C388192C01
1.656,0.271 1.969,0.479 0.313,0.208 10 false *a 0.552,2.281 0.75,2.49 0.198,0.208 10 true *b
*a Torque Wrench Fulcrum Length
*b Flare Nut


Using a 17 mm union nut wrench, fully tighten the flare nut to install the motor cooling pipe assembly.

Torque:
Specified tightening torque : 34 N*m (350 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)):

29 N*m (296 kgf*cm, 21 ft.*lbf)

·

Turn the flare nut while holding the union.




Hide 51442C 8.INSTALL ENGINE UNDER COVER LH